Hi there everyone, I apologise if you already got this, my yahoo account has been really acting up, and I have an new ISP email free anyways, so here I am. I'm not sure if this went through last time, but sorry if you are getting it twice. Well I got a shiny new internal us robotics 56k real honest guv hardware modem and just installed it. Works with windows, it is plug and play though. I decided since I have a PS2 mouse, to put it on com1, and in the bios of my machine I disabled the "auto" set feature for com1. So I used the isapnp.onf below to allot it to com1 ran the isapnp comand and I got the following error message: [error message begins] lspci not found, so PCI resource conflict not checked on or around line 13OM2. Script asupplied by SuSE tech support /etc/isapnp.conf:13 -- Fatal - Error occurred parsing config file --- no action taken [error message ends] [isapnp.conf begins below] ##################################################################### # $Id: pnpdump.c,v 1.9 1997/06/10 21:37:32 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER # Assigns modem to COM1. Script asupplied by SuSE tech support # March 1999, the morning after the night before. - Dom # # Trying port address 0203 # Board 1 has serial identifier 7b 9f e4 ab a7 30 30 72 56 # (DEBUG) (READPORT 0x0203) (ISOLATE) (IDENTIFY *) # Card 1: (serial identifier 7b 9f e4 ab a7 30 30 72 56) # USR3030 Serial No -1612403801 [checksum 7b] # Version 1.0, Vendor version 0.0 # ANSI string -->U.S. Robotics 56K FAX INT<-- # # Logical device id USR3030 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be # changed if # required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE USR3030/-1612403801 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02f8)) # IRQ 3, 5 or 7. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 (IO 0 (BASE 0x03f8)) # IRQ 2, 3, 4, 5 or 7. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x03e8)) # IRQ 2, 3, 4, 5 or 7. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x02e8)) # IRQ 2, 3, 4, 5 or 7. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 2 (MODE +E))) # Start dependent functions: priority acceptable # End dependent functions (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY) [EOF] Any help would be most appreciated! Cheers! Dom -- To get out of this list, please send email to [EMAIL PROTECTED] with this text in its body: unsubscribe suse-linux-e Check out the SuSE-FAQ at http://www.suse.com/Support/Doku/FAQ/ and the archive at http://www.suse.com/Mailinglists/suse-linux-e/index.html
