Author: yongari
Date: Thu Jan 5 20:31:58 2012
New Revision: 229642
URL: http://svn.freebsd.org/changeset/base/229642
Log:
MFC r228086:
Announce flow control capability to PHY drivers and enable flow
control for all vr(4) controllers that support it. It's known that
old vr(4) controllers(Rhine II) does not support TX pause but Rhine
III supports both TX and RX pause.
Make TX pause really work on Rhine III by letting controller know
available RX buffers.
While here, adjust XON/XOFF parameters to get better performance
with flow control.
Modified:
stable/8/sys/dev/vr/if_vr.c
stable/8/sys/dev/vr/if_vrreg.h
Directory Properties:
stable/8/sys/ (props changed)
stable/8/sys/amd64/include/xen/ (props changed)
stable/8/sys/cddl/contrib/opensolaris/ (props changed)
stable/8/sys/contrib/dev/acpica/ (props changed)
stable/8/sys/contrib/pf/ (props changed)
Modified: stable/8/sys/dev/vr/if_vr.c
==============================================================================
--- stable/8/sys/dev/vr/if_vr.c Thu Jan 5 20:30:16 2012 (r229641)
+++ stable/8/sys/dev/vr/if_vr.c Thu Jan 5 20:31:58 2012 (r229642)
@@ -309,7 +309,7 @@ vr_miibus_statchg(device_t dev)
(ifp->if_drv_flags & IFF_DRV_RUNNING) == 0)
return;
- sc->vr_flags &= ~VR_F_LINK;
+ sc->vr_flags &= ~(VR_F_LINK | VR_F_TXPAUSE);
if ((mii->mii_media_status & (IFM_ACTIVE | IFM_AVALID)) ==
(IFM_ACTIVE | IFM_AVALID)) {
switch (IFM_SUBTYPE(mii->mii_media_active)) {
@@ -346,7 +346,6 @@ vr_miibus_statchg(device_t dev)
CSR_WRITE_1(sc, VR_CR1, cr1);
}
fc = 0;
-#ifdef notyet
/* Configure flow-control. */
if (sc->vr_revid >= REV_ID_VT6105_A0) {
fc = CSR_READ_1(sc, VR_FLOWCR1);
@@ -355,8 +354,10 @@ vr_miibus_statchg(device_t dev)
IFM_ETH_RXPAUSE) != 0)
fc |= VR_FLOWCR1_RXPAUSE;
if ((IFM_OPTIONS(mii->mii_media_active) &
- IFM_ETH_TXPAUSE) != 0)
+ IFM_ETH_TXPAUSE) != 0) {
fc |= VR_FLOWCR1_TXPAUSE;
+ sc->vr_flags |= VR_F_TXPAUSE;
+ }
CSR_WRITE_1(sc, VR_FLOWCR1, fc);
} else if (sc->vr_revid >= REV_ID_VT6102_A) {
/* No Tx puase capability available for Rhine II. */
@@ -367,7 +368,6 @@ vr_miibus_statchg(device_t dev)
fc |= VR_MISCCR0_RXPAUSE;
CSR_WRITE_1(sc, VR_MISC_CR0, fc);
}
-#endif
vr_rx_start(sc);
vr_tx_start(sc);
} else {
@@ -770,7 +770,8 @@ vr_attach(device_t dev)
else
phy = CSR_READ_1(sc, VR_PHYADDR) & VR_PHYADDR_MASK;
error = mii_attach(dev, &sc->vr_miibus, ifp, vr_ifmedia_upd,
- vr_ifmedia_sts, BMSR_DEFCAPMASK, phy, MII_OFFSET_ANY, 0);
+ vr_ifmedia_sts, BMSR_DEFCAPMASK, phy, MII_OFFSET_ANY,
+ sc->vr_revid >= REV_ID_VT6102_A ? MIIF_DOPAUSE : 0);
if (error != 0) {
device_printf(dev, "attaching PHYs failed\n");
goto fail;
@@ -1400,6 +1401,17 @@ vr_rxeof(struct vr_softc *sc)
}
if (prog > 0) {
+ /*
+ * Let controller know how many number of RX buffers
+ * are posted but avoid expensive register access if
+ * TX pause capability was not negotiated with link
+ * partner.
+ */
+ if ((sc->vr_flags & VR_F_TXPAUSE) != 0) {
+ if (prog >= VR_RX_RING_CNT)
+ prog = VR_RX_RING_CNT - 1;
+ CSR_WRITE_1(sc, VR_FLOWCR0, prog);
+ }
sc->vr_cdata.vr_rx_cons = cons;
bus_dmamap_sync(sc->vr_cdata.vr_rx_ring_tag,
sc->vr_cdata.vr_rx_ring_map,
@@ -2075,14 +2087,32 @@ vr_init_locked(struct vr_softc *sc)
/* Set flow-control parameters for Rhine III. */
if (sc->vr_revid >= REV_ID_VT6105_A0) {
- /* Rx buffer count available for incoming packet. */
- CSR_WRITE_1(sc, VR_FLOWCR0, VR_RX_RING_CNT);
/*
- * Tx pause low threshold : 16 free receive buffers
- * Tx pause XON high threshold : 48 free receive buffers
+ * Configure Rx buffer count available for incoming
+ * packet.
+ * Even though data sheet says almost nothing about
+ * this register, this register should be updated
+ * whenever driver adds new RX buffers to controller.
+ * Otherwise, XON frame is not sent to link partner
+ * even if controller has enough RX buffers and you
+ * would be isolated from network.
+ * The controller is not smart enough to know number
+ * of available RX buffers so driver have to let
+ * controller know how many RX buffers are posted.
+ * In other words, this register works like a residue
+ * counter for RX buffers and should be initialized
+ * to the number of total RX buffers - 1 before
+ * enabling RX MAC. Note, this register is 8bits so
+ * it effectively limits the maximum number of RX
+ * buffer to be configured by controller is 255.
+ */
+ CSR_WRITE_1(sc, VR_FLOWCR0, VR_RX_RING_CNT - 1);
+ /*
+ * Tx pause low threshold : 8 free receive buffers
+ * Tx pause XON high threshold : 24 free receive buffers
*/
CSR_WRITE_1(sc, VR_FLOWCR1,
- VR_FLOWCR1_TXLO16 | VR_FLOWCR1_TXHI48 | VR_FLOWCR1_XONXOFF);
+ VR_FLOWCR1_TXLO8 | VR_FLOWCR1_TXHI24 | VR_FLOWCR1_XONXOFF);
/* Set Tx pause timer. */
CSR_WRITE_2(sc, VR_PAUSETIMER, 0xffff);
}
@@ -2110,7 +2140,7 @@ vr_init_locked(struct vr_softc *sc)
ifp->if_drv_flags |= IFF_DRV_RUNNING;
ifp->if_drv_flags &= ~IFF_DRV_OACTIVE;
- sc->vr_flags &= ~VR_F_LINK;
+ sc->vr_flags &= ~(VR_F_LINK | VR_F_TXPAUSE);
mii_mediachg(mii);
callout_reset(&sc->vr_stat_callout, hz, vr_tick, sc);
@@ -2132,6 +2162,7 @@ vr_ifmedia_upd(struct ifnet *ifp)
mii = device_get_softc(sc->vr_miibus);
LIST_FOREACH(miisc, &mii->mii_phys, mii_list)
mii_phy_reset(miisc);
+ sc->vr_flags &= ~(VR_F_LINK | VR_F_TXPAUSE);
error = mii_mediachg(mii);
VR_UNLOCK(sc);
Modified: stable/8/sys/dev/vr/if_vrreg.h
==============================================================================
--- stable/8/sys/dev/vr/if_vrreg.h Thu Jan 5 20:30:16 2012
(r229641)
+++ stable/8/sys/dev/vr/if_vrreg.h Thu Jan 5 20:31:58 2012
(r229642)
@@ -722,6 +722,7 @@ struct vr_softc {
uint8_t vr_revid; /* Rhine chip revision */
int vr_flags; /* See VR_F_* below */
#define VR_F_RESTART 0x0001 /* Restart unit on next
tick */
+#define VR_F_TXPAUSE 0x0010
#define VR_F_SUSPENDED 0x2000
#define VR_F_DETACHED 0x4000
#define VR_F_LINK 0x8000
_______________________________________________
svn-src-all@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/svn-src-all
To unsubscribe, send any mail to "svn-src-all-unsubscr...@freebsd.org"
