> Adam [AdameK] Wojciechowski wrote:
>> ale partycja dalej sie nie montuje podczas startu.
> Coś w logach?
Feb 15 10:49:26 localhost kernel: Ending clean XFS mount for filesystem: hda1
Feb 15 10:49:26 localhost kernel: Ending clean XFS mount for filesystem: hda3
Feb 15 10:49:26 localhost kernel: libata version 1.02 loaded.
Feb 15 10:49:26 localhost kernel: sata_via version 0.20
Feb 15 10:49:26 localhost kernel: ata1: dev 0 cfg 49:2f00 82:746b 83:7f61
84:4163 85:7469 86:3c41 87:4163 88:407f
Feb 15 10:50:00 localhost kernel: Ending clean XFS mount for filesystem: sda1
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
ani razu po rebocie nie była podmontowana
Feb 15 10:51:21 localhost kernel: Ending clean XFS mount for filesystem: hda1
Feb 15 10:51:21 localhost kernel: Ending clean XFS mount for filesystem: hda3
Feb 15 10:51:21 localhost kernel: libata version 1.02 loaded.
Feb 15 10:51:21 localhost kernel: sata_via version 0.20
Feb 15 10:51:21 localhost kernel: ata1: dev 0 cfg 49:2f00 82:746b 83:7f61
84:4163 85:7469 86:3c41 87:4163 88:407f
W dmesg:
[ciach]
libata version 1.02 loaded.
sata_via version 0.20
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 193
sata_via(0000:00:0f.0): routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xDA00 ctl 0xE002 bmdma 0xD900 irq 193
ata2: SATA max UDMA/133 cmd 0xE100 ctl 0xD802 bmdma 0xD908 irq 193
ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4163 85:7469 86:3c41 87:4163 88:407f
ata1: dev 0 ATA, max UDMA/133, 781422768 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: no device found (phy stat 00000000)
scsi1 : sata_via
Vendor: ATA Model: WDC WD4000KS-00M Rev: 07.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 781422768 512-byte hdwr sectors (400088 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ciach]
brak jakiejkolwiek zmianki o próbie zamontowania. Partycje z małego dysku
normalnie mają:
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 193
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xdb00-0xdb07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xdb08-0xdb0f, BIOS settings: hdc:pio, hdd:pio
hda: SAMSUNG SP0411N, ATA DISK drive
hdb: LG CD-ROM CRD-8522B, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: max request size: 1024KiB
hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug
enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda1
Ending clean XFS mount for filesystem: hda1
Adding 1951888k swap on /dev/hda2. Priority:-1 extents:1
Generic RTC Driver v1.07
hdb: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
[ciach]
SCSI subsystem initialized
Capability LSM initialized
[ciach]
XFS mounting filesystem hda3
Ending clean XFS mount for filesystem: hda3
>> mount -t xfs /dev/sda1 /samba
>> odrazu ładnie podmontowywuje partycje.
> mount -t auto /dev/sda1 /samba działa?
Partycja sie podmontowywuje tak samo jak z -t xfs.
Po kazdym rebocia trza ją na nowo zamontować :(
Pozdrawiam
Adam [AdameK] Wojciechowski
