RE: [Talk] Variable not updating

[White, Scott A]

Oddly enough, I used this logic, which did make the : go away. Now the script produces random RESULTS..... even when a device is not in use I still get the Else statement to evaluate and populate the message.   Thank you for helping me to get rid of the : though.   Still need the system to actually evaluate the If, Then, Else statement correctly.   Very strange?!?!?!?!??? -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Larry Briggs Sent: Thursday, October 21, 2004 4:11 PM To: [EMAIL PROTECTED] Subject: RE: [Talk] Variable not updating can you change ...     Else: M1Result = "Modem.1 is in use on " & mydate     End If   to     ...     Else      M1Result = "Modem.1 is in use on " & mydate     End If   ? -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of White, Scott A Sent: Thursday, October 21, 2004 4:08 PM To: [EMAIL PROTECTED] Subject: RE: [Talk] Variable not updating Yes; but each time I tried to take the : out after the Else, VB would put it back in again.   I'm stumped!!!! -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]On Behalf Of Adams,Ernest Sent: Thursday, October 21, 2004 4:02 PM To: '[EMAIL PROTECTED]' Subject: RE: [Talk] Variable not updating Scott:   The problem is the colon following the Else.  VB thinks "Else:" is a label rather than an else clause of the If.   Pax, Ernest 21 Oct 04 -----Original Message----- From: White, Scott A [mailto:[EMAIL PROTECTED] Sent: Thursday, October 21, 2004 3:55 PM To: [EMAIL PROTECTED] Subject: [Talk] Variable not updating Hello, I've got a small script that runs well except for the result of M2Result and M3Result seen below.  The script will run and send the results to me in MOX; but it ALWAYS sends me the  Modem.2 is in use on " & mydate and Modem.3 is in use on " & mydate   Oddly enough, Modem.1 sends the correct info.  Can you tell by looking at this, why it wouldn't evaluate the If statements?  None of the devices have been in use all day; but my script ignores that for Modem.2 and Modem.3 .  I've even initialized all three at the beginning of the procedure.       Pause "Device" Enter "MODEM.1"     Wait 2     If At("Device is not in use") Then     M1Result = "Modem.1 Not In use at this time"     Else: M1Result = "Modem.1 is in use on " & mydate     End If     Key "{F11}"     Wait 1                     Enter "MODEM.2"             Wait 2             If At("Device is not in use") Then             M2Result = "Modem.2 Not In use at this time"             Else: M2Result = "Modem.2 is in use on " & mydate             End If             Key "{F11}"             Wait 1                                                     Enter "MODEM.3"                 Wait 2                     If At("Device is not in use") Then                     M3Result = "Modem.3 Not In use at this time"                     Else: M3Result = "Modem.3 is in use on " & mydate                     End If                     Key "{F11}"                     Wait 1                           Thank you, Scott    CONFIDENTIALITY NOTICE: This e-mail communication and any attachments may contain confidential and privileged information for the use of the designated recipients named above.  If you are not the intended recipient, you are hereby notified that you have received this communication in error and that any review, disclosure, dissemination, distribution or copying of it or its contents is prohibited. If you have received this communication in error, please notify Saratoga Hospital immediately by e-mail at [EMAIL PROTECTED] and destroy all copies of this communication and any attachments. CONFIDENTIALITY NOTICE: This e-mail message, including any attachments, is for the sole use of the intended recipient(s) and may contain confidential and privileged information.  Any unauthorized review, use, disclosure or distribution is prohibited. ZirMed, Inc. has strict policies regarding the content of e-mail communications, specifically Protected Health Information, any communications containing such material will be returned to the originating party with such advisement noted. If you are not the intended recipient, please contact the sender by reply e-mail and destroy all copies of the original message.

<<image001.jpg>>