I am not that familiar with Xen. Maybe Michael S can answer from here. Where do you see hostid->none error? I you could just copy and paste your messages to the screen maybe I can help. It has been awhile since I have encountered these error so I might not remember exactly what to do. However, if you show me exactly what is printed to the screen, it may job my memory.
Richard On Fri, Apr 29, 2011 at 2:06 AM, hari narayanan <[email protected]> wrote: > Sorry for the trouble ... We created the Vm based on the hostname found in > /etc/hosts. After creating the vm, we still get hostid->none error... > gethosts at the CM lists our laptop, but primitive.py says "Failed to > schedule or activate vm" ... vncviewer works for domU images in xen... so, > if we add the host (laptop) , then how can we vncview into it considering > its dom0? > > On Thu, Apr 28, 2011 at 5:14 PM, Richard Gass <[email protected]> wrote: >> >> Tashi doesn't use thrift anymore. We switched to rpyc. Install that. >> >> If you didn't have ipython installed, when you start the CM or NM, you >> would not have an active prompt, just log messages. If you restart >> now, you should get an ipython prompt. Can you show the output of >> data.baseDataObject.hosts now? >> >> Richard >> >> >> On Fri, Apr 29, 2011 at 12:10 AM, hari narayanan <[email protected]> >> wrote: >> > No, but we installed it just now ... we dont have thrift installed .... >> > should we get that also ?? >> > >> > And we always start CM as u said .... >> > >> > >> > >> > On Thu, Apr 28, 2011 at 4:49 PM, Richard Gass <[email protected]> >> > wrote: >> >> >> >> Do you have ipython installed? >> >> >> >> On Thu, Apr 28, 2011 at 11:38 PM, hari narayanan >> >> <[email protected]> >> >> wrote: >> >> > We dont get output for data.baseDataObject.hosts in CM .... but, we >> >> > get >> >> > the >> >> > laptop name in tashiclient. getHosts with state Normal... >> >> > >> >> > On Thu, Apr 28, 2011 at 4:32 PM, Richard Gass <[email protected]> >> >> > wrote: >> >> >> >> >> >> Send me the following information. on the CM >> >> >> "data.baseDataObject.hosts" or from the tashi client "tashi >> >> >> gethosts" >> >> >> >> >> >> >> >> >> On Thu, Apr 28, 2011 at 11:22 PM, hari narayanan >> >> >> <[email protected]> >> >> >> wrote: >> >> >> > Hi, >> >> >> > >> >> >> > we are able to start the vm image using xen command... but, it >> >> >> > doesnt >> >> >> > work >> >> >> > when we try with tashi ... Still get the same error "no >> >> >> > hostid-none" >> >> >> > ... >> >> >> > We >> >> >> > tried to change the CM and NM config files to make sure that >> >> >> > hostid >> >> >> > value is >> >> >> > equal to our actual laptop's hostname "akshay" ... and also ,we >> >> >> > are >> >> >> > able >> >> >> > to >> >> >> > ping the address and hostname of the laptop ... what could be the >> >> >> > prob? >> >> >> > >> >> >> > On Tue, Apr 26, 2011 at 10:16 PM, Akshay Sheth >> >> >> > <[email protected]> >> >> >> > wrote: >> >> >> >> >> >> >> >> Hey Micheal, >> >> >> >> >> >> >> >> I was planning to use Sqlite3 but when I write the insert queries >> >> >> >> that >> >> >> >> the >> >> >> >> tables hosts and networks dont exist. How do I fix this? Also >> >> >> >> when I >> >> >> >> put >> >> >> >> data.baseDataObject.getHosts on CM I dont get any output. Also >> >> >> >> eventually I >> >> >> >> get no hostId for the VM. What could be wrong? >> >> >> >> >> >> >> >> Thanks >> >> >> >> Akshay >> >> >> >> >> >> >> >> On Tue, Apr 26, 2011 at 9:55 PM, hari narayanan >> >> >> >> <[email protected]> >> >> >> >> wrote: >> >> >> >>> >> >> >> >>> Hi, >> >> >> >>> >> >> >> >>> we have managed to setup internet in xen and downloaded tashi >> >> >> >>> also >> >> >> >>> ... >> >> >> >>> now, we get a different error in node manager... failed to load >> >> >> >>> vminfo >> >> >> >>> /var/tmp/nm.data ... and no vm information found in >> >> >> >>> /var/tmp/vmcontrolQemu >> >> >> >>> ... When we used vmcspecificcall, we get the same no hostd none >> >> >> >>> error >> >> >> >>> >> >> >> >>> Thanks, >> >> >> >>> Hari >> >> >> >>> >> >> >> >>> On Tue, Apr 26, 2011 at 6:50 PM, Michael Stroucken <[email protected]> >> >> >> >>> wrote: >> >> >> >>>> >> >> >> >>>> hari narayanan wrote: >> >> >> >>>>> >> >> >> >>>>> Sorry ... We couldnt get it work . so, we moved to Xen .... >> >> >> >>>> >> >> >> >>>> Hi Hari, >> >> >> >>>> >> >> >> >>>> I used to use Xen until I had too many problems with booting >> >> >> >>>> kernels >> >> >> >>>> inside the VM image. But with kvm I'm using the same network >> >> >> >>>> setup >> >> >> >>>> as >> >> >> >>>> I did >> >> >> >>>> with Xen, except for having to add the qemu-ifup files that I >> >> >> >>>> mentioned >> >> >> >>>> before. >> >> >> >>>> >> >> >> >>>> >> >> >> >>>> Greetings, >> >> >> >>>> Michael. >> >> >> >>> >> >> >> >> >> >> >> > >> >> >> > >> >> >> >> >> >> >> >> >> >> >> >> -- >> >> >> Richard Gass >> >> > >> >> > >> >> >> >> >> >> >> >> -- >> >> Richard Gass >> > >> > >> >> >> >> -- >> Richard Gass > > -- Richard Gass
