On Sun, Jun 27, 2010 at 09:48:03AM -0700, Matthew Dempsky wrote:
> Anyone still using ioprbs(4)? If so, please test the diff below and
> report back to me.
>
No bad effects seen after light testing on a ADAPTEC 3200S that I found in
a dark corner of the basement. Dmesg below.
--
:wq Claudio
OpenBSD 4.7-current (GENERIC) #0: Tue Jul 13 12:50:08 CEST 2010
r...@foo.networx.ch:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 804 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,MMX,FXSR,SSE
real mem = 536358912 (511MB)
avail mem = 517607424 (493MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 06/12/01, BIOS32 rev. 0 @ 0xf0ad0, SMBIOS
rev. 2.3 @ 0xf2970 (46 entries)
bios0: vendor Award Software, Inc. version "ASUS CUV4X-E ACPI BIOS Revision
1003" date 06/12/2001
bios0: ASUSTeK Computer INC. CUV4X-E
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x1322
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf1280/160 (8 entries)
pcibios0: PCI Interrupt Router at 000:04:0 ("VIA VT82C586 ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xc000 0xcc000/0x1800 0xd0000/0x5000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 PCI" rev 0xc4
viaagp0 at pchb0: v2
agp0 at viaagp0: aperture at 0xfc000000, size 0x10000000
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage 128 Pro" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 4 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 4 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100, channel 0
configured to compatibility, channel 1 configured to compatibility
pciide0: channel 0 ignored (disabled)
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-540E, 1.0A> ATAPI 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
viaenv0 at pci0 dev 4 function 4 "VIA VT82C686 SMBus" rev 0x40: HWM disabled:
24-bit timer at 3579545Hz
fxp0 at pci0 dev 8 function 0 "Intel 8255x" rev 0x0c, i82550: irq 10, address
00:02:b3:27:f1:67
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
ppb1 at pci0 dev 11 function 0 "DPT PCI-PCI" rev 0x02
pci2 at ppb1 bus 2
iop0 at pci0 dev 11 function 1 "DPT SmartRAID (I2O)" rev 0x02: : <ADAPTEC
3200S>, irq 11
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask fb65 netmask ff65 ttymask ffff
mtrr: Pentium Pro MTRR support
iop0: configuring...
ioprbs0 at iop0 tid 518: <IBM, DDYS-T18350M, S93E> direct access, fixed
scsibus1 at ioprbs0: 1 targets
sd0 at scsibus1 targ 0 lun 0: <I2O, Container #00, > SCSI2 0/direct fixed
sd0: 17501MB, 512 bytes/sec, 35843653 sec total
ioprbs1 at iop0 tid 517: <IBM-ESXS, DTN036W3UWDY10FN, S25J> direct access, fixed
scsibus2 at ioprbs1: 1 targets
sd1 at scsibus2 targ 0 lun 0: <I2O, Container #00, > SCSI2 0/direct fixed
sd1: 34715MB, 512 bytes/sec, 71096623 sec total
ioprbs2 at iop0 tid 521: <ADAPTEC, RAID-1, 320H> direct access, fixed
scsibus3 at ioprbs2: 1 targets
sd2 at scsibus3 targ 0 lun 0: <I2O, Container #00, > SCSI2 0/direct fixed
sd2: 8678MB, 512 bytes/sec, 17772544 sec total
iopsp0 at iop0 tid 8: SCSI port <ADAPTEC, AIC-7899, 00000001>
scsibus4 at iopsp0: 16 targets, initiator 7
iopsp1 at iop0 tid 9: SCSI port <ADAPTEC, AIC-7899, 00000001>
scsibus5 at iopsp1: 16 targets, initiator 7
iopsp2 at iop0 tid 10: SCSI port <ADAPTEC, AIC-7899, 00000001>
scsibus6 at iopsp2: 16 targets, initiator 7
iopsp3 at iop0 tid 11: SCSI port <ADAPTEC, AIC-7899, 00000001>
scsibus7 at iopsp3: 16 targets, initiator 7
vscsi0 at root
scsibus8 at vscsi0: 256 targets
softraid0 at root
root on sd0a swap on sd0b dump on sd0b
