On Sat, May 21, 2011 at 22:42, Chris Cappuccio <ch...@nmedia.net> wrote:
> Alexey Suslikov [alexey.susli...@gmail.com] wrote:
>> I have to disable wbsio(4) on X8SIL-based Supermicro box since leaving it
>> enabled leads to weird things: sudden overheating alarms while no
>> overheating,
>> front panel "fault" led blinking while no errors recorded in BIOS log,
>> etc.
>
> I had the same problem with an IPMI X8SIL-F but never with the regular X8SIL
>
> Do you have the -F or other IPMI version?
>
Where should I look for IPMI version?
Taken from new box, below is a more or less recent dmesg for X8SIL
plus hw.sensors output.
Things to mention:
1) Still need to disable wbsio(4). Same bug: with wbsio(4) enabled fan
blows to max speed at some point, front panel alarm led is flashing,
but no errors seen in BIOS log.
--- dmesg_full.txt Tue May 24 19:10:48 2011
+++ dmesg_good.txt Thu May 26 21:03:28 2011
@@ -125,8 +125,6 @@
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
-wbsio0 at isa0 port 0x2e/2: W83627DHG rev 0x25
-lm1 at wbsio0 port 0xa10/8: W83627DHG
mtrr: Pentium Pro MTRR support
uhub2 at uhub0 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Winbond
Electronics Corp Hermon USB hidmouse Device" rev 1.10/0.01 addr 3
2) Sometimes (after cold boot?) spdmem(4) isn't attaching:
--- dmesg_good.txt Thu May 26 21:03:28 2011
+++ dmesg_eeprom.txt Tue May 24 23:29:56 2011
@@ -111,8 +111,8 @@
iic0 at ichiic0
admtemp0 at iic0 addr 0x18: Xeon
admtemp1 at iic0 addr 0x1a: Xeon
-spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM ECC PC3-10600 with thermal sensor
-spdmem1 at iic0 addr 0x52: 4GB DDR3 SDRAM ECC PC3-10600 with thermal sensor
+"eeprom" at iic0 addr 0x50 not configured
+"eeprom" at iic0 addr 0x52 not configured
pciide1 at pci0 dev 31 function 5 "Intel 3400 SATA" rev 0x05: DMA,
channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide1: using apic 8 int 19 for native-PCI interrupt
isa0 at pcib0
3) Xeon embedded temperature sensors show bogus values:
hw.sensors.admtemp0.temp0=2.00 degC (Xeon)
hw.sensors.admtemp0.temp1=0.00 degC (Xeon)
hw.sensors.admtemp1.temp0=2.00 degC (Xeon)
hw.sensors.admtemp1.temp1=0.00 degC (Xeon
Alexey
OpenBSD 4.9-current (GENERIC.MP) #0: Mon May 23 17:16:17 EEST 2011
***@***:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 8580038656 (8182MB)
avail mem = 8337588224 (7951MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.6 @ 0x9f000 (68 entries)
bios0: vendor American Megatrends Inc. version "1.1" date 05/27/2010
bios0: Supermicro X8SIL
acpi0 at bios0: rev 2
acpi0: sleep states S0 S1 S4 S5
acpi0: tables DSDT FACP APIC MCFG OEMB HPET GSCI SSDT EINJ BERT ERST HEST
acpi0: wakeup devices P0P1(S4) P0P3(S4) P0P4(S4) P0P5(S4) P0P6(S4)
BR1E(S4) PS2K(S4) PS2M(S4) USB0(S4) USB1(S4) USB2(S4) USB3(S4)
USB4(S4) USB5(S4) USB6(S4) GBE_(S4) BR20(S4) BR21(S4) BR22(S4)
BR23(S4) BR24(S4) BR25(S4) BR26(S4) BR27(S4) EUSB(S4) USBE(S4)
SLPB(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.66 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: apic clock running at 133MHz
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu1: 256KB 64b/line 8-way L2 cache
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu2: 256KB 64b/line 8-way L2 cache
cpu3 at mainbus0: apid 6 (application processor)
cpu3: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu3: 256KB 64b/line 8-way L2 cache
cpu4 at mainbus0: apid 1 (application processor)
cpu4: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu4:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu4: 256KB 64b/line 8-way L2 cache
cpu5 at mainbus0: apid 3 (application processor)
cpu5: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu5:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu5: 256KB 64b/line 8-way L2 cache
cpu6 at mainbus0: apid 5 (application processor)
cpu6: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu6:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu6: 256KB 64b/line 8-way L2 cache
cpu7 at mainbus0: apid 7 (application processor)
cpu7: Intel(R) Xeon(R) CPU X3440 @ 2.53GHz, 2533.33 MHz
cpu7:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,SSE4.2,POPCNT,NXE,LONG
cpu7: 256KB 64b/line 8-way L2 cache
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 1, remapped to apid 8
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (P0P1)
acpiprt2 at acpi0: bus 1 (P0P3)
acpiprt3 at acpi0: bus 2 (P0P5)
acpiprt4 at acpi0: bus -1 (P0P6)
acpiprt5 at acpi0: bus 6 (BR1E)
acpiprt6 at acpi0: bus 3 (BR20)
acpiprt7 at acpi0: bus 4 (BR24)
acpiprt8 at acpi0: bus 5 (BR25)
acpicpu0 at acpi0: C3, C2, C1, PSS
acpicpu1 at acpi0: C3, C2, C1, PSS
acpicpu2 at acpi0: C3, C2, C1, PSS
acpicpu3 at acpi0: C3, C2, C1, PSS
acpicpu4 at acpi0: C3, C2, C1, PSS
acpicpu5 at acpi0: C3, C2, C1, PSS
acpicpu6 at acpi0: C3, C2, C1, PSS
acpicpu7 at acpi0: C3, C2, C1, PSS
acpibtn0 at acpi0: SLPB
acpibtn1 at acpi0: PWRB
ipmi at mainbus0 not configured
cpu0: Enhanced SpeedStep 2533 MHz: speeds: 2534, 2533, 2400, 2267,
2133, 2000, 1867, 1733, 1600, 1467, 1333, 1200 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core DMI" rev 0x11
ppb0 at pci0 dev 3 function 0 "Intel Core PCIE" rev 0x11: apic 8 int 16
pci1 at ppb0 bus 1
ppb1 at pci0 dev 5 function 0 "Intel Core PCIE" rev 0x11: apic 8 int 16
pci2 at ppb1 bus 2
"Intel Core Management" rev 0x11 at pci0 dev 8 function 0 not configured
"Intel Core Scratch" rev 0x11 at pci0 dev 8 function 1 not configured
"Intel Core Control" rev 0x11 at pci0 dev 8 function 2 not configured
"Intel Core Misc" rev 0x11 at pci0 dev 8 function 3 not configured
"Intel Core QPI Link" rev 0x11 at pci0 dev 16 function 0 not configured
"Intel Core QPI Routing" rev 0x11 at pci0 dev 16 function 1 not configured
ehci0 at pci0 dev 26 function 0 "Intel 3400 USB" rev 0x05: apic 8 int 21
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb2 at pci0 dev 28 function 0 "Intel 3400 PCIE" rev 0x05: apic 8 int 17
pci3 at ppb2 bus 3
ppb3 at pci0 dev 28 function 4 "Intel 3400 PCIE" rev 0x05: apic 8 int 17
pci4 at ppb3 bus 4
em0 at pci4 dev 0 function 0 "Intel PRO/1000 MT (82574L)" rev 0x00:
apic 8 int 16, address 00:25:90:34:c5:aa
ppb4 at pci0 dev 28 function 5 "Intel 3400 PCIE" rev 0x05: apic 8 int 16
pci5 at ppb4 bus 5
em1 at pci5 dev 0 function 0 "Intel PRO/1000 MT (82574L)" rev 0x00:
apic 8 int 17, address 00:25:90:34:c5:ab
ehci1 at pci0 dev 29 function 0 "Intel 3400 USB" rev 0x05: apic 8 int 23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb5 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xa5
pci6 at ppb5 bus 6
vga1 at pci6 dev 3 function 0 "Matrox MGA G200eW" rev 0x0a
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 31 function 0 "Intel 3420 LPC" rev 0x05
pciide0 at pci0 dev 31 function 2 "Intel 3400 SATA" rev 0x05: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 8 int 19 for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <Hitachi HUA722010CLA330>
wd0: 16-sector PIO, LBA48, 953869MB, 1953525168 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 3400 SMBus" rev 0x05: apic 8 int 18
iic0 at ichiic0
admtemp0 at iic0 addr 0x18: Xeon
admtemp1 at iic0 addr 0x1a: Xeon
spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM ECC PC3-10600 with thermal sensor
spdmem1 at iic0 addr 0x52: 4GB DDR3 SDRAM ECC PC3-10600 with thermal sensor
pciide1 at pci0 dev 31 function 5 "Intel 3400 SATA" rev 0x05: DMA,
channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide1: using apic 8 int 19 for native-PCI interrupt
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
mtrr: Pentium Pro MTRR support
uhub2 at uhub0 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
uhidev0 at uhub2 port 2 configuration 1 interface 0 "Winbond
Electronics Corp Hermon USB hidmouse Device" rev 1.10/0.01 addr 3
uhidev0: iclass 3/1
ums0 at uhidev0: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
uhidev1 at uhub2 port 2 configuration 1 interface 1 "Winbond
Electronics Corp Hermon USB hidmouse Device" rev 1.10/0.01 addr 3
uhidev1: iclass 3/1
ukbd0 at uhidev1: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhub3 at uhub1 port 1 "Intel Rate Matching Hub" rev 2.00/0.00 addr 2
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
hw.sensors.cpu0.temp0=44.00 degC
hw.sensors.cpu1.temp0=44.00 degC
hw.sensors.cpu2.temp0=44.00 degC
hw.sensors.cpu3.temp0=44.00 degC
hw.sensors.cpu4.temp0=44.00 degC
hw.sensors.cpu5.temp0=44.00 degC
hw.sensors.cpu6.temp0=44.00 degC
hw.sensors.cpu7.temp0=44.00 degC
hw.sensors.admtemp0.temp0=2.00 degC (Xeon)
hw.sensors.admtemp0.temp1=0.00 degC (Xeon)
hw.sensors.admtemp1.temp0=2.00 degC (Xeon)
hw.sensors.admtemp1.temp1=0.00 degC (Xeon)
