I can confirm that hdr->max_svc / hdr->pause_svc messed up with my
"Intel WiFi Link 5100" and the patch works without them.
Best Regards,
mpp
On 09/09/14 17:29, Fabian Raetz wrote:
> On Tue, Sep 09, 2014 at 12:38:04PM +0200, Fabian Raetz wrote:
>> Hi,
>>
>> below is a patch for iwn(4) which hopefully fixes a problem where iwn(4)
>> does not return from a scan, if the interface is up.
>
> here's an updated version which does not
> set hdr->max_svc / hdr->pause_svc.
>
> Cristoph Zimmermann noticed that scan requests return no APs on his
> device (thanks for testing).
> iwn0 at pci2 dev 0 function 0 "Intel WiFi Link 5100" rev 0x00: msi, MIMO
> 1T2R, MoW, address 00:21:6b:a3:70:7a
>
> As Piotr and Mike tested the patch from Piotr which does not set this
> values either and it still works on my card, this should the way to go
> for now.
>
>
> Index: if_iwn.c
> ===================================================================
> RCS file: /cvs/src/sys/dev/pci/if_iwn.c,v
> retrieving revision 1.133
> diff -u -p -r1.133 if_iwn.c
> --- if_iwn.c 22 Jul 2014 13:12:11 -0000 1.133
> +++ if_iwn.c 9 Sep 2014 14:57:34 -0000
> @@ -220,6 +220,9 @@ int iwn_send_btcoex(struct iwn_softc *)
> int iwn_send_advanced_btcoex(struct iwn_softc *);
> int iwn5000_runtime_calib(struct iwn_softc *);
> int iwn_config(struct iwn_softc *);
> +uint16_t iwn_get_active_dwell_time(struct iwn_softc *, uint16_t,
> uint8_t);
> +uint16_t iwn_limit_dwell(struct iwn_softc *, uint16_t);
> +uint16_t iwn_get_passive_dwell_time(struct iwn_softc *, uint16_t);
> int iwn_scan(struct iwn_softc *, uint16_t);
> int iwn_auth(struct iwn_softc *);
> int iwn_run(struct iwn_softc *);
> @@ -4424,6 +4427,66 @@ iwn_config(struct iwn_softc *sc)
> return 0;
> }
>
> +uint16_t
> +iwn_get_active_dwell_time(struct iwn_softc *sc,
> + uint16_t flags, uint8_t n_probes)
> +{
> + /* No channel? Default to 2GHz settings */
> + if (flags & IEEE80211_CHAN_2GHZ) {
> + return (IWN_ACTIVE_DWELL_TIME_2GHZ +
> + IWN_ACTIVE_DWELL_FACTOR_2GHZ * (n_probes + 1));
> + }
> +
> + /* 5GHz dwell time */
> + return (IWN_ACTIVE_DWELL_TIME_5GHZ +
> + IWN_ACTIVE_DWELL_FACTOR_5GHZ * (n_probes + 1));
> +}
> +
> +/*
> + * Limit the total dwell time to 85% of the beacon interval.
> + *
> + * Returns the dwell time in milliseconds.
> + */
> +uint16_t
> +iwn_limit_dwell(struct iwn_softc *sc, uint16_t dwell_time)
> +{
> + struct ieee80211com *ic = &sc->sc_ic;
> + struct ieee80211_node *ni = ic->ic_bss;
> + int bintval = 0;
> +
> + /* bintval is in TU (1.024mS) */
> + if (ni != NULL)
> + bintval = ni->ni_intval;
> +
> + /*
> + * If it's non-zero, we should calculate the minimum of
> + * it and the DWELL_BASE.
> + *
> + * XXX Yes, the math should take into account that bintval
> + * is 1.024mS, not 1mS..
> + */
> + if (bintval > 0) {
> + return (MIN(IWN_PASSIVE_DWELL_BASE, ((bintval * 85) / 100)));
> + }
> +
> + /* No association context? Default */
> + return (IWN_PASSIVE_DWELL_BASE);
> +}
> +
> +uint16_t
> +iwn_get_passive_dwell_time(struct iwn_softc *sc, uint16_t flags)
> +{
> + uint16_t passive;
> + if (flags & IEEE80211_CHAN_2GHZ) {
> + passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_2GHZ;
> + } else {
> + passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_5GHZ;
> + }
> +
> + /* Clamp to the beacon interval if we're associated */
> + return (iwn_limit_dwell(sc, passive));
> +}
> +
> int
> iwn_scan(struct iwn_softc *sc, uint16_t flags)
> {
> @@ -4436,9 +4499,9 @@ iwn_scan(struct iwn_softc *sc, uint16_t
> struct ieee80211_rateset *rs;
> struct ieee80211_channel *c;
> uint8_t *buf, *frm;
> - uint16_t rxchain;
> + uint16_t rxchain, dwell_active, dwell_passive;
> uint8_t txant;
> - int buflen, error;
> + int buflen, error, is_active;
>
> buf = malloc(IWN_SCAN_MAXSZ, M_DEVBUF, M_NOWAIT | M_ZERO);
> if (buf == NULL) {
> @@ -4474,7 +4537,6 @@ iwn_scan(struct iwn_softc *sc, uint16_t
> tx->lifetime = htole32(IWN_LIFETIME_INFINITE);
>
> if (flags & IEEE80211_CHAN_5GHZ) {
> - hdr->crc_threshold = 0xffff;
> /* Send probe requests at 6Mbps. */
> tx->plcp = iwn_rates[IWN_RIDX_OFDM6].plcp;
> rs = &ic->ic_sup_rates[IEEE80211_MODE_11A];
> @@ -4488,12 +4550,23 @@ iwn_scan(struct iwn_softc *sc, uint16_t
> /* Use the first valid TX antenna. */
> txant = IWN_LSB(sc->txchainmask);
> tx->rflags |= IWN_RFLAG_ANT(txant);
> +
> + /*
> + * Only do active scanning if we're announcing a probe request
> + * for a given SSID (or more, if we ever add it to the driver.)
> + */
> + is_active = 0;
>
> + /*
> + * If we're scanning for a specific SSID, add it to the command.
> + */
> essid = (struct iwn_scan_essid *)(tx + 1);
> if (ic->ic_des_esslen != 0) {
> essid[0].id = IEEE80211_ELEMID_SSID;
> essid[0].len = ic->ic_des_esslen;
> memcpy(essid[0].data, ic->ic_des_essid, ic->ic_des_esslen);
> +
> + is_active = 1;
> }
> /*
> * Build a probe request frame. Most of the following code is a
> @@ -4522,6 +4595,41 @@ iwn_scan(struct iwn_softc *sc, uint16_t
> /* Set length of probe request. */
> tx->len = htole16(frm - (uint8_t *)wh);
>
> + /*
> + * If active scanning is requested but a certain channel is
> + * marked passive, we can do active scanning if we detect
> + * transmissions.
> + *
> + * There is an issue with some firmware versions that triggers
> + * a sysassert on a "good CRC threshold" of zero (== disabled),
> + * on a radar channel even though this means that we should NOT
> + * send probes.
> + *
> + * The "good CRC threshold" is the number of frames that we
> + * need to receive during our dwell time on a channel before
> + * sending out probes -- setting this to a huge value will
> + * mean we never reach it, but at the same time work around
> + * the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER
> + * here instead of IWL_GOOD_CRC_TH_DISABLED.
> + *
> + * This was fixed in later versions along with some other
> + * scan changes, and the threshold behaves as a flag in those
> + * versions.
> + */
> +
> + /*
> + * If we're doing active scanning, set the crc_threshold
> + * to a suitable value. This is different to active veruss
> + * passive scanning depending upon the channel flags; the
> + * firmware will obey that particular check for us.
> + */
> + if (sc->tlv_feature_flags & IWN_UCODE_TLV_FLAGS_NEWSCAN)
> + hdr->crc_threshold = is_active ?
> + IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_DISABLED;
> + else
> + hdr->crc_threshold = is_active ?
> + IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_NEVER;
> +
> chan = (struct iwn_scan_chan *)frm;
> for (c = &ic->ic_channels[1];
> c <= &ic->ic_channels[IEEE80211_CHAN_MAX]; c++) {
> @@ -4531,19 +4639,33 @@ iwn_scan(struct iwn_softc *sc, uint16_t
> chan->chan = htole16(ieee80211_chan2ieee(ic, c));
> DPRINTFN(2, ("adding channel %d\n", chan->chan));
> chan->flags = 0;
> - if (!(c->ic_flags & IEEE80211_CHAN_PASSIVE))
> - chan->flags |= htole32(IWN_CHAN_ACTIVE);
> if (ic->ic_des_esslen != 0)
> chan->flags |= htole32(IWN_CHAN_NPBREQS(1));
> +
> + if (c->ic_flags & IEEE80211_CHAN_PASSIVE)
> + chan->flags |= htole32(IWN_CHAN_PASSIVE);
> + else
> + chan->flags |= htole32(IWN_CHAN_ACTIVE);
> +
> + /*
> + * Calculate the active/passive dwell times.
> + */
> +
> + dwell_active = iwn_get_active_dwell_time(sc, flags, is_active);
> + dwell_passive = iwn_get_passive_dwell_time(sc, flags);
> +
> + /* Make sure they're valid */
> + if (dwell_passive <= dwell_active)
> + dwell_passive = dwell_active + 1;
> +
> + chan->active = htole16(dwell_active);
> + chan->passive = htole16(dwell_passive);
> +
> chan->dsp_gain = 0x6e;
> if (IEEE80211_IS_CHAN_5GHZ(c)) {
> chan->rf_gain = 0x3b;
> - chan->active = htole16(24);
> - chan->passive = htole16(110);
> } else {
> chan->rf_gain = 0x28;
> - chan->active = htole16(36);
> - chan->passive = htole16(120);
> }
> hdr->nchan++;
> chan++;
> @@ -5580,6 +5702,14 @@ iwn_read_firmware_tlv(struct iwn_softc *
> sc->reset_noise_gain = letoh32(*ptr);
> sc->noise_gain = letoh32(*ptr) + 1;
> }
> + break;
> + case IWN_FW_TLV_FLAGS:
> + if (len < sizeof(uint32_t))
> + break;
> + if (len % sizeof(uint32_t))
> + break;
> + sc->tlv_feature_flags = letoh32(*ptr);
> + DPRINTF(("feature: 0x%08x\n", sc->tlv_feature_flags));
> break;
> default:
> DPRINTF(("TLV type %d not handled\n",
> Index: if_iwnreg.h
> ===================================================================
> RCS file: /cvs/src/sys/dev/pci/if_iwnreg.h,v
> retrieving revision 1.47
> diff -u -p -r1.47 if_iwnreg.h
> --- if_iwnreg.h 11 Feb 2014 19:30:10 -0000 1.47
> +++ if_iwnreg.h 9 Sep 2014 14:57:34 -0000
> @@ -799,6 +799,7 @@ struct iwn_scan_hdr {
>
> struct iwn_scan_chan {
> uint32_t flags;
> +#define IWN_CHAN_PASSIVE (0 << 0)
> #define IWN_CHAN_ACTIVE (1 << 0)
> #define IWN_CHAN_NPBREQS(x) (((1 << (x)) - 1) << 1)
>
> @@ -812,6 +813,51 @@ struct iwn_scan_chan {
> /* Maximum size of a scan command. */
> #define IWN_SCAN_MAXSZ (MCLBYTES - 4)
>
> +/*
> + * For active scan, listen ACTIVE_DWELL_TIME (msec) on each channel after
> + * sending probe req. This should be set long enough to hear probe responses
> + * from more than one AP.
> + */
> +#define IWN_ACTIVE_DWELL_TIME_2GHZ (30) /* all times in msec */
> +#define IWN_ACTIVE_DWELL_TIME_5GHZ (20)
> +#define IWN_ACTIVE_DWELL_FACTOR_2GHZ (3)
> +#define IWN_ACTIVE_DWELL_FACTOR_5GHZ (2)
> +
> +/*
> + * For passive scan, listen PASSIVE_DWELL_TIME (msec) on each channel.
> + * Must be set longer than active dwell time.
> + * For the most reliable scan, set > AP beacon interval (typically 100msec).
> + */
> +#define IWN_PASSIVE_DWELL_TIME_2GHZ (20) /* all times in msec */
> +#define IWN_PASSIVE_DWELL_TIME_5GHZ (10)
> +#define IWN_PASSIVE_DWELL_BASE (100)
> +#define IWN_CHANNEL_TUNE_TIME (5)
> +
> +/*
> + * If active scanning is requested but a certain channel is
> + * marked passive, we can do active scanning if we detect
> + * transmissions.
> + *
> + * There is an issue with some firmware versions that triggers
> + * a sysassert on a "good CRC threshold" of zero (== disabled),
> + * on a radar channel even though this means that we should NOT
> + * send probes.
> + *
> + * The "good CRC threshold" is the number of frames that we
> + * need to receive during our dwell time on a channel before
> + * sending out probes -- setting this to a huge value will
> + * mean we never reach it, but at the same time work around
> + * the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER
> + * here instead of IWL_GOOD_CRC_TH_DISABLED.
> + *
> + * This was fixed in later versions along with some other
> + * scan changes, and the threshold behaves as a flag in those
> + * versions.
> + */
> +#define IWN_GOOD_CRC_TH_DISABLED 0
> +#define IWN_GOOD_CRC_TH_DEFAULT htole16(1)
> +#define IWN_GOOD_CRC_TH_NEVER htole16(0xffff)
> +
> /* Structure for command IWN_CMD_TXPOWER (4965AGN only.) */
> #define IWN_RIDX_MAX 32
> struct iwn4965_cmd_txpower {
> @@ -1407,6 +1453,7 @@ struct iwn_fw_tlv {
> #define IWN_FW_TLV_PBREQ_MAXLEN 6
> #define IWN_FW_TLV_ENH_SENS 14
> #define IWN_FW_TLV_PHY_CALIB 15
> +#define IWN_FW_TLV_FLAGS 18
>
> uint16_t alt;
> uint32_t len;
> @@ -1419,6 +1466,60 @@ struct iwn_fw_tlv {
> #define IWN_FW_BOOT_TEXT_MAXSZ 1024
> #define IWN4965_FWSZ (IWN4965_FW_TEXT_MAXSZ + IWN4965_FW_DATA_MAXSZ)
> #define IWN5000_FWSZ IWN5000_FW_TEXT_MAXSZ
> +
> +/*
> + * Microcode flags TLV (18.)
> + */
> +
> +/**
> + * enum iwn_ucode_tlv_flag - ucode API flags
> + * @IWN_UCODE_TLV_FLAGS_PAN: This is PAN capable microcode; this previously
> + * was a separate TLV but moved here to save space.
> + * @IWN_UCODE_TLV_FLAGS_NEWSCAN: new uCode scan behaviour on hidden SSID,
> + * treats good CRC threshold as a boolean
> + * @IWN_UCODE_TLV_FLAGS_MFP: This uCode image supports MFP (802.11w).
> + * @IWN_UCODE_TLV_FLAGS_P2P: This uCode image supports P2P.
> + * @IWN_UCODE_TLV_FLAGS_DW_BC_TABLE: The SCD byte count table is in DWORDS
> + * @IWN_UCODE_TLV_FLAGS_UAPSD: This uCode image supports uAPSD
> + * @IWN_UCODE_TLV_FLAGS_SHORT_BL: 16 entries of black list instead of 64 in
> scan
> + * offload profile config command.
> + * @IWN_UCODE_TLV_FLAGS_RX_ENERGY_API: supports rx signal strength api
> + * @IWN_UCODE_TLV_FLAGS_TIME_EVENT_API_V2: using the new time event API.
> + * @IWN_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS: D3 image supports up to six
> + * (rather than two) IPv6 addresses
> + * @IWN_UCODE_TLV_FLAGS_BF_UPDATED: new beacon filtering API
> + * @IWN_UCODE_TLV_FLAGS_NO_BASIC_SSID: not sending a probe with the SSID
> element
> + * from the probe request template.
> + * @IWN_UCODE_TLV_FLAGS_D3_CONTINUITY_API: modified D3 API to allow keeping
> + * connection when going back to D0
> + * @IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL: new NS offload (small version)
> + * @IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE: new NS offload (large version)
> + * @IWN_UCODE_TLV_FLAGS_SCHED_SCAN: this uCode image supports scheduled scan.
> + * @IWN_UCODE_TLV_FLAGS_STA_KEY_CMD: new ADD_STA and ADD_STA_KEY command API
> + * @IWN_UCODE_TLV_FLAGS_DEVICE_PS_CMD: support device wide power command
> + * containing CAM (Continuous Active Mode) indication.
> + */
> +enum iwn_ucode_tlv_flag {
> + IWN_UCODE_TLV_FLAGS_PAN = (1 << 0),
> + IWN_UCODE_TLV_FLAGS_NEWSCAN = (1 << 1),
> + IWN_UCODE_TLV_FLAGS_MFP = (1 << 2),
> + IWN_UCODE_TLV_FLAGS_P2P = (1 << 3),
> + IWN_UCODE_TLV_FLAGS_DW_BC_TABLE = (1 << 4),
> + IWN_UCODE_TLV_FLAGS_NEWBT_COEX = (1 << 5),
> + IWN_UCODE_TLV_FLAGS_UAPSD = (1 << 6),
> + IWN_UCODE_TLV_FLAGS_SHORT_BL = (1 << 7),
> + IWN_UCODE_TLV_FLAGS_RX_ENERGY_API = (1 << 8),
> + IWN_UCODE_TLV_FLAGS_TIME_EVENT_API_V2 = (1 << 9),
> + IWN_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS = (1 << 10),
> + IWN_UCODE_TLV_FLAGS_BF_UPDATED = (1 << 11),
> + IWN_UCODE_TLV_FLAGS_NO_BASIC_SSID = (1 << 12),
> + IWN_UCODE_TLV_FLAGS_D3_CONTINUITY_API = (1 << 14),
> + IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL = (1 << 15),
> + IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE = (1 << 16),
> + IWN_UCODE_TLV_FLAGS_SCHED_SCAN = (1 << 17),
> + IWN_UCODE_TLV_FLAGS_STA_KEY_CMD = (1 << 19),
> + IWN_UCODE_TLV_FLAGS_DEVICE_PS_CMD = (1 << 20),
> +};
>
> /*
> * Offsets into EEPROM.
> Index: if_iwnvar.h
> ===================================================================
> RCS file: /cvs/src/sys/dev/pci/if_iwnvar.h,v
> retrieving revision 1.27
> diff -u -p -r1.27 if_iwnvar.h
> --- if_iwnvar.h 10 Feb 2014 19:08:58 -0000 1.27
> +++ if_iwnvar.h 9 Sep 2014 14:57:34 -0000
> @@ -284,6 +284,8 @@ struct iwn_softc {
> uint8_t reset_noise_gain;
> uint8_t noise_gain;
>
> + uint32_t tlv_feature_flags;
> +
> int32_t temp_off;
> uint32_t int_mask;
> uint8_t ntxchains;
>
>
>>
>> This patch was backported from this FreeBSD commit
>> https://svnweb.freebsd.org/base?view=revision&revision=258829
>> ---------
>> Overhaul the iwn(4) scan infrastructure to be slightly more "correct"
>> for these chipsets.
>>
>> * Correctly set the active/passive flag in the scan request - this is
>> NOT a "is the channel active|passive"; it's to do with whether we
>> have an SSID to actively scan for or not. The firmware takes care
>> of the active/passive setup of the channel.
>>
>> * Calculate the active/passive dwell time based on the beacon interval
>> and the channel mode, rather than using a hard coded value.
>>
>> * For now, hardcode the scan service_time. It's defined as:
>>
>> 31:22 - number of beacon intervals to come back onto the home channel
>> for;
>> 0:21 - time (microseconds) to come back onto the home channel for.
>>
>> When doing an active scan when the NIC is active (whether we're associated
>> or not - it only matters if we've setup the NIC to a destination or not)
>> this determines how much time to stay on the home channel for when
>> scanning. We can tune this based on the amount of active traffic.
>>
>> For now it's 4 beacon intervals and 100 microseconds.
>>
>> * Fix the "good crc threshold" setting. It differs based on the NIC
>> firmware. Some older firmware required a workaround; the later
>> firmware instead treats the field as a flag.
>>
>> * Enforce that we are not sending a scan command if one is already
>> pending. Any time this is done is a bug and it absolutely needs
>> to be fixed - so be very loud.
>>
>> * Add the SCAN flag to a few debug messages that are scan related but
>> only occuring under STATE.
>>
>> Now, this does get noisy when you're scanning in an actively busy 2GHz
>> network as the firmware (for reason I don't quite yet understand) seems
>> hell bent on staying on some passive channels longer than it should.
>> However, it should eventually recover and complete the scan.
>> ----------
>>
>> Marcin Piotr Pawlowski came up with the same diff (without comments) and
>> send it to me in a private mail. Thanks!
>>
>> I kept all comments to reduce the diff to FreeBSD's iwn(4).
>> In iwn_limit_dwell(struct iwn_softc *sc, uint16_t dwell_time), the
>> dwell_time is unused, so there could probably some code be removed.
>>
>>
>> Devices tested so far:
>>
>> Inter WiFi Link 5100 (Marcin Piotr Pawlowski)
>> Intel Centrino Advanced-N 6205 (Mike Burns, who also reported the
>> problem on misc@, thanks!)
>> Intel Centrino Wireless-N 2230 (Fabian Raetz)
>>
>>
>> More tests are much appreciated :)
>>
>>
>> Regards,
>> Fabian
>>
>>
>> Index: if_iwn.c
>> ===================================================================
>> RCS file: /cvs/src/sys/dev/pci/if_iwn.c,v
>> retrieving revision 1.133
>> diff -u -p -r1.133 if_iwn.c
>> --- if_iwn.c 22 Jul 2014 13:12:11 -0000 1.133
>> +++ if_iwn.c 9 Sep 2014 09:47:48 -0000
>> @@ -220,6 +220,9 @@ int iwn_send_btcoex(struct iwn_softc *)
>> int iwn_send_advanced_btcoex(struct iwn_softc *);
>> int iwn5000_runtime_calib(struct iwn_softc *);
>> int iwn_config(struct iwn_softc *);
>> +uint16_t iwn_get_active_dwell_time(struct iwn_softc *, uint16_t,
>> uint8_t);
>> +uint16_t iwn_limit_dwell(struct iwn_softc *, uint16_t);
>> +uint16_t iwn_get_passive_dwell_time(struct iwn_softc *, uint16_t);
>> int iwn_scan(struct iwn_softc *, uint16_t);
>> int iwn_auth(struct iwn_softc *);
>> int iwn_run(struct iwn_softc *);
>> @@ -4424,6 +4427,66 @@ iwn_config(struct iwn_softc *sc)
>> return 0;
>> }
>>
>> +uint16_t
>> +iwn_get_active_dwell_time(struct iwn_softc *sc,
>> + uint16_t flags, uint8_t n_probes)
>> +{
>> + /* No channel? Default to 2GHz settings */
>> + if (flags & IEEE80211_CHAN_2GHZ) {
>> + return (IWN_ACTIVE_DWELL_TIME_2GHZ +
>> + IWN_ACTIVE_DWELL_FACTOR_2GHZ * (n_probes + 1));
>> + }
>> +
>> + /* 5GHz dwell time */
>> + return (IWN_ACTIVE_DWELL_TIME_5GHZ +
>> + IWN_ACTIVE_DWELL_FACTOR_5GHZ * (n_probes + 1));
>> +}
>> +
>> +/*
>> + * Limit the total dwell time to 85% of the beacon interval.
>> + *
>> + * Returns the dwell time in milliseconds.
>> + */
>> +uint16_t
>> +iwn_limit_dwell(struct iwn_softc *sc, uint16_t dwell_time)
>> +{
>> + struct ieee80211com *ic = &sc->sc_ic;
>> + struct ieee80211_node *ni = ic->ic_bss;
>> + int bintval = 0;
>> +
>> + /* bintval is in TU (1.024mS) */
>> + if (ni != NULL)
>> + bintval = ni->ni_intval;
>> +
>> + /*
>> + * If it's non-zero, we should calculate the minimum of
>> + * it and the DWELL_BASE.
>> + *
>> + * XXX Yes, the math should take into account that bintval
>> + * is 1.024mS, not 1mS..
>> + */
>> + if (bintval > 0) {
>> + return (MIN(IWN_PASSIVE_DWELL_BASE, ((bintval * 85) / 100)));
>> + }
>> +
>> + /* No association context? Default */
>> + return (IWN_PASSIVE_DWELL_BASE);
>> +}
>> +
>> +uint16_t
>> +iwn_get_passive_dwell_time(struct iwn_softc *sc, uint16_t flags)
>> +{
>> + uint16_t passive;
>> + if (flags & IEEE80211_CHAN_2GHZ) {
>> + passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_2GHZ;
>> + } else {
>> + passive = IWN_PASSIVE_DWELL_BASE + IWN_PASSIVE_DWELL_TIME_5GHZ;
>> + }
>> +
>> + /* Clamp to the beacon interval if we're associated */
>> + return (iwn_limit_dwell(sc, passive));
>> +}
>> +
>> int
>> iwn_scan(struct iwn_softc *sc, uint16_t flags)
>> {
>> @@ -4436,9 +4499,10 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> struct ieee80211_rateset *rs;
>> struct ieee80211_channel *c;
>> uint8_t *buf, *frm;
>> - uint16_t rxchain;
>> + uint32_t scan_service_time;
>> + uint16_t rxchain, dwell_active, dwell_passive;
>> uint8_t txant;
>> - int buflen, error;
>> + int buflen, error, is_active;
>>
>> buf = malloc(IWN_SCAN_MAXSZ, M_DEVBUF, M_NOWAIT | M_ZERO);
>> if (buf == NULL) {
>> @@ -4453,6 +4517,21 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> */
>> hdr->quiet_time = htole16(10); /* timeout in milliseconds */
>> hdr->quiet_threshold = htole16(1); /* min # of packets */
>> + /*
>> + * Max needs to be greater than active and passive and quiet!
>> + * It's also in microseconds!
>> + */
>> + hdr->max_svc = htole32(250 * 1024);
>> +
>> +
>> + /*
>> + * Reset scan: interval=100
>> + * Normal scan: interval=beacon interval
>> + * suspend_time: 100 (TU)
>> + *
>> + */
>> + scan_service_time = (4 << 22) | (100 * 1024); /* Hardcode for now! */
>> + hdr->pause_svc = htole32(scan_service_time);
>>
>> /* Select antennas for scanning. */
>> rxchain =
>> @@ -4474,7 +4553,6 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> tx->lifetime = htole32(IWN_LIFETIME_INFINITE);
>>
>> if (flags & IEEE80211_CHAN_5GHZ) {
>> - hdr->crc_threshold = 0xffff;
>> /* Send probe requests at 6Mbps. */
>> tx->plcp = iwn_rates[IWN_RIDX_OFDM6].plcp;
>> rs = &ic->ic_sup_rates[IEEE80211_MODE_11A];
>> @@ -4488,12 +4566,23 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> /* Use the first valid TX antenna. */
>> txant = IWN_LSB(sc->txchainmask);
>> tx->rflags |= IWN_RFLAG_ANT(txant);
>> +
>> + /*
>> + * Only do active scanning if we're announcing a probe request
>> + * for a given SSID (or more, if we ever add it to the driver.)
>> + */
>> + is_active = 0;
>>
>> + /*
>> + * If we're scanning for a specific SSID, add it to the command.
>> + */
>> essid = (struct iwn_scan_essid *)(tx + 1);
>> if (ic->ic_des_esslen != 0) {
>> essid[0].id = IEEE80211_ELEMID_SSID;
>> essid[0].len = ic->ic_des_esslen;
>> memcpy(essid[0].data, ic->ic_des_essid, ic->ic_des_esslen);
>> +
>> + is_active = 1;
>> }
>> /*
>> * Build a probe request frame. Most of the following code is a
>> @@ -4522,6 +4611,41 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> /* Set length of probe request. */
>> tx->len = htole16(frm - (uint8_t *)wh);
>>
>> + /*
>> + * If active scanning is requested but a certain channel is
>> + * marked passive, we can do active scanning if we detect
>> + * transmissions.
>> + *
>> + * There is an issue with some firmware versions that triggers
>> + * a sysassert on a "good CRC threshold" of zero (== disabled),
>> + * on a radar channel even though this means that we should NOT
>> + * send probes.
>> + *
>> + * The "good CRC threshold" is the number of frames that we
>> + * need to receive during our dwell time on a channel before
>> + * sending out probes -- setting this to a huge value will
>> + * mean we never reach it, but at the same time work around
>> + * the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER
>> + * here instead of IWL_GOOD_CRC_TH_DISABLED.
>> + *
>> + * This was fixed in later versions along with some other
>> + * scan changes, and the threshold behaves as a flag in those
>> + * versions.
>> + */
>> +
>> + /*
>> + * If we're doing active scanning, set the crc_threshold
>> + * to a suitable value. This is different to active veruss
>> + * passive scanning depending upon the channel flags; the
>> + * firmware will obey that particular check for us.
>> + */
>> + if (sc->tlv_feature_flags & IWN_UCODE_TLV_FLAGS_NEWSCAN)
>> + hdr->crc_threshold = is_active ?
>> + IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_DISABLED;
>> + else
>> + hdr->crc_threshold = is_active ?
>> + IWN_GOOD_CRC_TH_DEFAULT : IWN_GOOD_CRC_TH_NEVER;
>> +
>> chan = (struct iwn_scan_chan *)frm;
>> for (c = &ic->ic_channels[1];
>> c <= &ic->ic_channels[IEEE80211_CHAN_MAX]; c++) {
>> @@ -4531,19 +4655,33 @@ iwn_scan(struct iwn_softc *sc, uint16_t
>> chan->chan = htole16(ieee80211_chan2ieee(ic, c));
>> DPRINTFN(2, ("adding channel %d\n", chan->chan));
>> chan->flags = 0;
>> - if (!(c->ic_flags & IEEE80211_CHAN_PASSIVE))
>> - chan->flags |= htole32(IWN_CHAN_ACTIVE);
>> if (ic->ic_des_esslen != 0)
>> chan->flags |= htole32(IWN_CHAN_NPBREQS(1));
>> +
>> + if (c->ic_flags & IEEE80211_CHAN_PASSIVE)
>> + chan->flags |= htole32(IWN_CHAN_PASSIVE);
>> + else
>> + chan->flags |= htole32(IWN_CHAN_ACTIVE);
>> +
>> + /*
>> + * Calculate the active/passive dwell times.
>> + */
>> +
>> + dwell_active = iwn_get_active_dwell_time(sc, flags, is_active);
>> + dwell_passive = iwn_get_passive_dwell_time(sc, flags);
>> +
>> + /* Make sure they're valid */
>> + if (dwell_passive <= dwell_active)
>> + dwell_passive = dwell_active + 1;
>> +
>> + chan->active = htole16(dwell_active);
>> + chan->passive = htole16(dwell_passive);
>> +
>> chan->dsp_gain = 0x6e;
>> if (IEEE80211_IS_CHAN_5GHZ(c)) {
>> chan->rf_gain = 0x3b;
>> - chan->active = htole16(24);
>> - chan->passive = htole16(110);
>> } else {
>> chan->rf_gain = 0x28;
>> - chan->active = htole16(36);
>> - chan->passive = htole16(120);
>> }
>> hdr->nchan++;
>> chan++;
>> @@ -5580,6 +5718,14 @@ iwn_read_firmware_tlv(struct iwn_softc *
>> sc->reset_noise_gain = letoh32(*ptr);
>> sc->noise_gain = letoh32(*ptr) + 1;
>> }
>> + break;
>> + case IWN_FW_TLV_FLAGS:
>> + if (len < sizeof(uint32_t))
>> + break;
>> + if (len % sizeof(uint32_t))
>> + break;
>> + sc->tlv_feature_flags = letoh32(*ptr);
>> + DPRINTF(("feature: 0x%08x\n", sc->tlv_feature_flags));
>> break;
>> default:
>> DPRINTF(("TLV type %d not handled\n",
>> Index: if_iwnreg.h
>> ===================================================================
>> RCS file: /cvs/src/sys/dev/pci/if_iwnreg.h,v
>> retrieving revision 1.47
>> diff -u -p -r1.47 if_iwnreg.h
>> --- if_iwnreg.h 11 Feb 2014 19:30:10 -0000 1.47
>> +++ if_iwnreg.h 9 Sep 2014 09:47:48 -0000
>> @@ -799,6 +799,7 @@ struct iwn_scan_hdr {
>>
>> struct iwn_scan_chan {
>> uint32_t flags;
>> +#define IWN_CHAN_PASSIVE (0 << 0)
>> #define IWN_CHAN_ACTIVE (1 << 0)
>> #define IWN_CHAN_NPBREQS(x) (((1 << (x)) - 1) << 1)
>>
>> @@ -812,6 +813,51 @@ struct iwn_scan_chan {
>> /* Maximum size of a scan command. */
>> #define IWN_SCAN_MAXSZ (MCLBYTES - 4)
>>
>> +/*
>> + * For active scan, listen ACTIVE_DWELL_TIME (msec) on each channel after
>> + * sending probe req. This should be set long enough to hear probe
>> responses
>> + * from more than one AP.
>> + */
>> +#define IWN_ACTIVE_DWELL_TIME_2GHZ (30) /* all times in msec */
>> +#define IWN_ACTIVE_DWELL_TIME_5GHZ (20)
>> +#define IWN_ACTIVE_DWELL_FACTOR_2GHZ (3)
>> +#define IWN_ACTIVE_DWELL_FACTOR_5GHZ (2)
>> +
>> +/*
>> + * For passive scan, listen PASSIVE_DWELL_TIME (msec) on each channel.
>> + * Must be set longer than active dwell time.
>> + * For the most reliable scan, set > AP beacon interval (typically 100msec).
>> + */
>> +#define IWN_PASSIVE_DWELL_TIME_2GHZ (20) /* all times in msec */
>> +#define IWN_PASSIVE_DWELL_TIME_5GHZ (10)
>> +#define IWN_PASSIVE_DWELL_BASE (100)
>> +#define IWN_CHANNEL_TUNE_TIME (5)
>> +
>> +/*
>> + * If active scanning is requested but a certain channel is
>> + * marked passive, we can do active scanning if we detect
>> + * transmissions.
>> + *
>> + * There is an issue with some firmware versions that triggers
>> + * a sysassert on a "good CRC threshold" of zero (== disabled),
>> + * on a radar channel even though this means that we should NOT
>> + * send probes.
>> + *
>> + * The "good CRC threshold" is the number of frames that we
>> + * need to receive during our dwell time on a channel before
>> + * sending out probes -- setting this to a huge value will
>> + * mean we never reach it, but at the same time work around
>> + * the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER
>> + * here instead of IWL_GOOD_CRC_TH_DISABLED.
>> + *
>> + * This was fixed in later versions along with some other
>> + * scan changes, and the threshold behaves as a flag in those
>> + * versions.
>> + */
>> +#define IWN_GOOD_CRC_TH_DISABLED 0
>> +#define IWN_GOOD_CRC_TH_DEFAULT htole16(1)
>> +#define IWN_GOOD_CRC_TH_NEVER htole16(0xffff)
>> +
>> /* Structure for command IWN_CMD_TXPOWER (4965AGN only.) */
>> #define IWN_RIDX_MAX 32
>> struct iwn4965_cmd_txpower {
>> @@ -1407,6 +1453,7 @@ struct iwn_fw_tlv {
>> #define IWN_FW_TLV_PBREQ_MAXLEN 6
>> #define IWN_FW_TLV_ENH_SENS 14
>> #define IWN_FW_TLV_PHY_CALIB 15
>> +#define IWN_FW_TLV_FLAGS 18
>>
>> uint16_t alt;
>> uint32_t len;
>> @@ -1419,6 +1466,60 @@ struct iwn_fw_tlv {
>> #define IWN_FW_BOOT_TEXT_MAXSZ 1024
>> #define IWN4965_FWSZ (IWN4965_FW_TEXT_MAXSZ +
>> IWN4965_FW_DATA_MAXSZ)
>> #define IWN5000_FWSZ IWN5000_FW_TEXT_MAXSZ
>> +
>> +/*
>> + * Microcode flags TLV (18.)
>> + */
>> +
>> +/**
>> + * enum iwn_ucode_tlv_flag - ucode API flags
>> + * @IWN_UCODE_TLV_FLAGS_PAN: This is PAN capable microcode; this previously
>> + * was a separate TLV but moved here to save space.
>> + * @IWN_UCODE_TLV_FLAGS_NEWSCAN: new uCode scan behaviour on hidden SSID,
>> + * treats good CRC threshold as a boolean
>> + * @IWN_UCODE_TLV_FLAGS_MFP: This uCode image supports MFP (802.11w).
>> + * @IWN_UCODE_TLV_FLAGS_P2P: This uCode image supports P2P.
>> + * @IWN_UCODE_TLV_FLAGS_DW_BC_TABLE: The SCD byte count table is in DWORDS
>> + * @IWN_UCODE_TLV_FLAGS_UAPSD: This uCode image supports uAPSD
>> + * @IWN_UCODE_TLV_FLAGS_SHORT_BL: 16 entries of black list instead of 64 in
>> scan
>> + * offload profile config command.
>> + * @IWN_UCODE_TLV_FLAGS_RX_ENERGY_API: supports rx signal strength api
>> + * @IWN_UCODE_TLV_FLAGS_TIME_EVENT_API_V2: using the new time event API.
>> + * @IWN_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS: D3 image supports up to six
>> + * (rather than two) IPv6 addresses
>> + * @IWN_UCODE_TLV_FLAGS_BF_UPDATED: new beacon filtering API
>> + * @IWN_UCODE_TLV_FLAGS_NO_BASIC_SSID: not sending a probe with the SSID
>> element
>> + * from the probe request template.
>> + * @IWN_UCODE_TLV_FLAGS_D3_CONTINUITY_API: modified D3 API to allow keeping
>> + * connection when going back to D0
>> + * @IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL: new NS offload (small version)
>> + * @IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE: new NS offload (large version)
>> + * @IWN_UCODE_TLV_FLAGS_SCHED_SCAN: this uCode image supports scheduled
>> scan.
>> + * @IWN_UCODE_TLV_FLAGS_STA_KEY_CMD: new ADD_STA and ADD_STA_KEY command API
>> + * @IWN_UCODE_TLV_FLAGS_DEVICE_PS_CMD: support device wide power command
>> + * containing CAM (Continuous Active Mode) indication.
>> + */
>> +enum iwn_ucode_tlv_flag {
>> + IWN_UCODE_TLV_FLAGS_PAN = (1 << 0),
>> + IWN_UCODE_TLV_FLAGS_NEWSCAN = (1 << 1),
>> + IWN_UCODE_TLV_FLAGS_MFP = (1 << 2),
>> + IWN_UCODE_TLV_FLAGS_P2P = (1 << 3),
>> + IWN_UCODE_TLV_FLAGS_DW_BC_TABLE = (1 << 4),
>> + IWN_UCODE_TLV_FLAGS_NEWBT_COEX = (1 << 5),
>> + IWN_UCODE_TLV_FLAGS_UAPSD = (1 << 6),
>> + IWN_UCODE_TLV_FLAGS_SHORT_BL = (1 << 7),
>> + IWN_UCODE_TLV_FLAGS_RX_ENERGY_API = (1 << 8),
>> + IWN_UCODE_TLV_FLAGS_TIME_EVENT_API_V2 = (1 << 9),
>> + IWN_UCODE_TLV_FLAGS_D3_6_IPV6_ADDRS = (1 << 10),
>> + IWN_UCODE_TLV_FLAGS_BF_UPDATED = (1 << 11),
>> + IWN_UCODE_TLV_FLAGS_NO_BASIC_SSID = (1 << 12),
>> + IWN_UCODE_TLV_FLAGS_D3_CONTINUITY_API = (1 << 14),
>> + IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_SMALL = (1 << 15),
>> + IWN_UCODE_TLV_FLAGS_NEW_NSOFFL_LARGE = (1 << 16),
>> + IWN_UCODE_TLV_FLAGS_SCHED_SCAN = (1 << 17),
>> + IWN_UCODE_TLV_FLAGS_STA_KEY_CMD = (1 << 19),
>> + IWN_UCODE_TLV_FLAGS_DEVICE_PS_CMD = (1 << 20),
>> +};
>>
>> /*
>> * Offsets into EEPROM.
>> Index: if_iwnvar.h
>> ===================================================================
>> RCS file: /cvs/src/sys/dev/pci/if_iwnvar.h,v
>> retrieving revision 1.27
>> diff -u -p -r1.27 if_iwnvar.h
>> --- if_iwnvar.h 10 Feb 2014 19:08:58 -0000 1.27
>> +++ if_iwnvar.h 9 Sep 2014 09:47:48 -0000
>> @@ -284,6 +284,8 @@ struct iwn_softc {
>> uint8_t reset_noise_gain;
>> uint8_t noise_gain;
>>
>> + uint32_t tlv_feature_flags;
>> +
>> int32_t temp_off;
>> uint32_t int_mask;
>> uint8_t ntxchains;
