Hi,

This patch does:

- Enable RX aggregation.
- Fix RX packet buffer alignment, using roundup() macro in sys/params.h.
- Call usbd_set_config before configuring endpoints in ure_init to fix
   an error when re-opening pipes.  I grabbed the code from if_kue.c.
- Make the chip recognize given MAC address.
- Remove ure_reset in ure_init, becasue its already called from ure_stop.

Regards,

--- sys/dev/usb/if_ure.c Wed May  3 22:20:15 2017
+++ sys/dev/usb/if_ure.c Mon Jun 19 09:11:09 2017
@@ -470,8 +470,6 @@ ure_init(void *xsc)
  /* Cancel pending I/O. */
  ure_stop(sc);

- ure_reset(sc);
-
  if (ure_rx_list_init(sc) == ENOBUFS) {
  printf("%s: rx list init failed\n", sc->ure_dev.dv_xname);
  splx(s);
@@ -484,9 +482,18 @@ ure_init(void *xsc)
  return;
  }

+#define URE_CONFIG_NO 1
+ if (usbd_set_config_no(sc->ure_udev, URE_CONFIG_NO, 1) ||
+    usbd_device2interface_handle(sc->ure_udev, URE_IFACE_IDX,
+ &sc->ure_iface))
+ printf("%s: set_config failed\n", sc->ure_dev.dv_xname);
+ usbd_delay_ms(sc->ure_udev, 10);
+
  /* Set MAC address. */
+ ure_write_1(sc, URE_PLA_CRWECR, URE_MCU_TYPE_PLA, URE_CRWECR_CONFIG);
  ure_write_mem(sc, URE_PLA_IDR, URE_MCU_TYPE_PLA | URE_BYTE_EN_SIX_BYTES,
     sc->ure_ac.ac_enaddr, 8);
+ ure_write_1(sc, URE_PLA_CRWECR, URE_MCU_TYPE_PLA, URE_CRWECR_NORAML);

  /* Reset the packet filter. */
  ure_write_2(sc, URE_PLA_FMC, URE_MCU_TYPE_PLA,
@@ -683,10 +690,10 @@ ure_rtl8152_init(struct ure_softc *sc)
     URE_GPHY_STS_MSK | URE_SPEED_DOWN_MSK | URE_SPDWN_RXDV_MSK |
     URE_SPDWN_LINKCHG_MSK);

- /* Disable Rx aggregation. */
+ /* Enable Rx aggregation. */
  ure_write_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB,
-    ure_read_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB) |
-    URE_RX_AGG_DISABLE);
+    ure_read_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB) &
+    ~URE_RX_AGG_DISABLE);

  /* Disable ALDPS. */
  ure_ocp_reg_write(sc, URE_OCP_ALDPS_CONFIG, URE_ENPDNPS | URE_LINKENA |
@@ -835,10 +842,10 @@ ure_rtl8153_init(struct ure_softc *sc)

  ure_init_fifo(sc);

- /* Disable Rx aggregation. */
+ /* Enable Rx aggregation. */
  ure_write_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB,
-    ure_read_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB) |
-    URE_RX_AGG_DISABLE);
+    ure_read_2(sc, URE_USB_USB_CTRL, URE_MCU_TYPE_USB) &
+    ~URE_RX_AGG_DISABLE);

  val = ure_read_2(sc, URE_USB_U2P3_CTRL, URE_MCU_TYPE_USB);
  if (!(sc->ure_chip & (URE_CHIP_VER_5C00 | URE_CHIP_VER_5C10)))
@@ -1289,7 +1296,7 @@ ure_rxeof(struct usbd_xfer *xfer, void *priv, usbd_sta
  goto done;
  }

- buf += pktlen;
+ buf += roundup(pktlen, 8);

  memcpy(&rxhdr, buf, sizeof(rxhdr));
  total_len -= sizeof(rxhdr);
@@ -1302,7 +1309,7 @@ ure_rxeof(struct usbd_xfer *xfer, void *priv, usbd_sta
  goto done;
  }

- total_len -= pktlen;
+ total_len -= roundup(pktlen, 8);
  buf += sizeof(rxhdr);

  m = m_devget(buf, pktlen, ETHER_ALIGN);

Reply via email to