Gents, I just uploaded a new version of Z38XX with the following improvements:
1) 115200 Baud setting bug removed 2) Should now recognize JACKSON LABS products and use partial/changed SCPI command set on those (Need feedback on that!) 3) Possible bug in status screen interpretation removed 4) Can display a nice nixie-clock like window like the one attached (only on devices that supply an answer to PTIM:TCOD? command i.e. the real Z-devices, no Fury/FireFly/GCRU) 5) Can compute a linear fit to the EFC value and compute a relative OCXO frequency drift from that due to a user supplied value that constitutes the assumed relation between EFC and frequency. Enjoy Ulrich Bangert > -----Ursprungliche Nachricht----- > Von: time-nuts-boun...@febo.com > [mailto:time-nuts-boun...@febo.com] Im Auftrag von Scott Mace > Gesendet: Samstag, 11. Juli 2009 19:30 > An: Discussion of precise time and frequency measurement > Betreff: Re: [time-nuts] Stable Z38XX > > > Ulrich, I'm trying to run this against a Fury and z38xx > doesn't seem to > keep the 115200 baud setting, it just changes back to 57600. > > Scott > > > On 07/11/2009 02:47 AM, Ulrich Bangert wrote: > > Hi Said, > > > > not necessary to supply you with a list: Just start the > software and > > open the debug window. You will see all serial > communication action. > > With no device connected just the commands will appeear one > below the > > other. You can use the "window hold" option of the debug window to > > defeat the scrolling. > > > > There is also a second option: If you supply ME a list of commands > > that your devices understand then I can detect the device > type by the > > answer to *IDN? and ask the devices just what they understand and > > leave everything else out. That is the stategy that the software > > already uses to cover the Z3801/5/15 and the GCRU. > > > > Best regards > > Ulrich > > > >> -----Ursprungliche Nachricht----- > >> Von: time-nuts-boun...@febo.com > [mailto:time-nuts-boun...@febo.com] > >> Im Auftrag von saidj...@aol.com > >> Gesendet: Freitag, 10. Juli 2009 20:23 > >> An: time-nuts@febo.com > >> Betreff: Re: [time-nuts] Stable Z38XX > >> > >> > >> Hi Ulrich, > >> > >> any chance you could send me a list of commands you > utility uses as a > >> minimum command-set so I can cross-check against our > >> Fury/FireFly GPSDO's? > >> > >> There are lots of folks on this list that have our units, and it > >> would be great if we could get it up and running for our > interface as > >> an alternative > >> to GPSCon. > >> > >> Thanks, > >> Said > >> > >> > >> In a message dated 7/10/2009 07:17:31 Pacific Daylight Time, > >> df...@ulrich-bangert.de writes: > >> > >> Guys, > >> > >> after a lot of help coming from Australia (thank you Hal and > >> Kit) there is > >> a > >> stable version of my Z38XX utility available. It handles > the Z3801, > >> the Z3805, the Z3815 and the GCRU. > >> > >> It is available from the usual place. Enjoy! > >> > >> Ulrich Bangert > >> www.ulrich-bangert.de > >> Ortholzer Weg 1 > >> 27243 Gross Ippener > >> > >> > >> _______________________________________________ > >> time-nuts mailing list -- time-nuts@febo.com > >> To unsubscribe, go to > >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > >> and follow the instructions there. > > > > > > _______________________________________________ > > time-nuts mailing list -- time-nuts@febo.com > > To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > > > > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there.
<<attachment: Z38XXClock.jpg>>
_______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.