Have you seen this: http://www.leapsecond.com/pages/tapr-tbolt/
and http://www.prc68.com/I/ThunderBolt.shtml Stanley ----- Original Message ---- From: SAL CORNACCHIA <salc...@rogers.com> To: Discussion of precise time and frequency measurement <time-nuts@febo.com> Sent: Fri, January 15, 2010 3:51:20 PM Subject: [time-nuts] need help on Tbolt Can someone help with the software for a Tbolt 35757256 built 6/2/05 A002206,61 Rev E, I just received this unit from China without any information or manual or software, I am about to built the power supply for it and would appreciate any help possible Best regards, Sal C. Cornacchia Electronic RF Microwave Engineer (Ret.) ________________________________ From: David C. Partridge <david.partri...@dsl.pipex.com> To: Discussion of precise time and frequency measurement <time-nuts@febo.com> Sent: Thu, January 14, 2010 1:14:36 PM Subject: Re: [time-nuts] T-Bolt Question Or use the beta realase of Lady Heather to do a 48 hour accurate survey. Dave -----Original Message----- From: time-nuts-boun...@febo.com [mailto:time-nuts-boun...@febo.com] On Behalf Of Ken Winterling Sent: 14 January 2010 17:53 To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] T-Bolt Question To All, The following procedure is taken from notes I made years ago when setting up my TBOLT using TBOLTMON. I have never had to enter the information again and the unit recovers automatically even after extended power failures that exhausted its UPS. Click Setup -> Self-Survey, Click the "Enable" and "Save" buttons Click "Set Survey", Click "Save Segment", Click "Close" Click Control -> Restart Self-Survey. The "Saved Position" alarm should change to green once the survey process finishes. You do not need to copy anything manually unless you want to specify a more-accurate survey position than what the Thunderbolt arrives at on its own. Ken, WA2LBI On Thu, Jan 14, 2010 at 12:07, Jim Mandaville <z...@dakotacom.net> wrote: > Starting without good saved coordinates will put you into search mode, > and it may take around 45 minutes to an hour to establish a position, > after which you will see SVs and AMUs. > > Once you get a good position, either from self-survey by the Tbolt or > by a different GPS, you can enter these as follows: > > On the Tbolt monitor main page: > > go to menu heading setting "setup"; under that, go to "position" > > In the "position" window, type in your coordinates. (The lat. and long. > must be in degrees and decimal degrees. If you are starting with > degrees, minutes and decimal minutes, divide the minutes with decimal > minutes by 60 and add the result to your original whole degrees.) The > longitude must start with a negative sign if it is west. For east, no sign is required. > > click "set accurate position"; then click "save segment" and close the > window > > you should now see the saved position in the main Tbolt window and the > Tbolt will now start from scratch using these coordinates. This will > reduce your fix time to a few minutes. > > Jim > > > > > > > > > HI Dick, >> I have the same problem and nothing works to enter the coordonates. >> More, i don't see the SV nor AMUs. >> 73 >> Alain >> F4GBC >> >> ----- Original Message ----- From: "Richard W. Solomon" < >> w1...@earthlink.net> >> >> To: <time-nuts@febo.com> >> Sent: Thursday, January 14, 2010 3:50 AM >> >> Subject: Re: [time-nuts] T-Bolt Question >> >> >>> Perhaps I posted this to the wrong forum ?? >>> Maybe if I had Duct-Taped it to a pendulum I may have gotten more >>> responses ?? >>> >>> 73, Dick, W1KSZ >>> >>> >>> -----Original Message----- >>> >>>> From: "Richard W.. Solomon" <w1...@earthlink.net> >>>> Sent: Jan 12, 2010 5:20 PM >>>> To: time-nuts@febo.com >>>> Subject: [time-nuts] E-Bolt Question >>>> >>>> I am in T-Bolt Monitor software. The "Saved Position" is Yellow. >>>> How do I get the T-Bolt to save the survey results ? >>>> >>>> Thanks, Dick, W1KSZ >>>> >>>> _______________________________________________ >>>> >>> > > _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www..febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.