Steve,
If you are worried about ground loops you should be using RS-422. I can almost guarantee you that pin 7 is attached to
the PCB ground plane which in turn is connected to chassis. Hopefully everyone is plugged into the same outlet and the
RS-232 signaling levels are sufficient to overcome the common mode noise.
Bob
----- Original Message -----
From: "Steve Rooke" <sar10...@gmail.com>
To: "Discussion of precise time and frequency measurement" <time-nuts@febo.com>
Sent: Monday, May 24, 2010 1:40 AM
Subject: Re: [time-nuts] Z3805 utility, Was: AW: (no subject)
On 24 May 2010 15:22, Robert Benward <rbenw...@verizon.net> wrote:
My experience with the term "straight through" is that I've seen RS-232
cable that have the ground pin connected to the shell. In a "straight
through" the pins are one to one and the only thing connected to the shell
would be the shield if one is available.
There is a difference between the signal ground on pin 7 and the shell
which forms a shield around the connector and may be connected to a
shield on the cable if there is one. You have to be careful with this
sort of setup though as earth loops can be caused by connecting the
chassis earth on two bits of equipment via the cable shield. That's
why pin 7 is the signalling earth and it really should not be
connected to earth at either end, IE. attempts at doing 2 wire
signalling et al.
Steve
Bob
----- Original Message ----- From: "Bob Camp" <li...@rtty.us>
To: "Discussion of precise time and frequency measurement"
<time-nuts@febo.com>
Sent: Sunday, May 23, 2010 9:21 PM
Subject: Re: [time-nuts] Z3805 utility, Was: AW: (no subject)
Hi
Long ago I decided to go with the terms "straight" and "null modem" for
the cables I use. NM and ST are easy to mark and hard to confuse.
Bob
On May 23, 2010, at 8:58 PM, jimlux wrote:
Stanley Reynolds wrote:
<snip>
Dec computers / terminal servers were as I described, but many brands
were different. Still have a BOB aka break out box with LEDs to
indicate levels, matching transmit and receive is easy, getting the
hardware flow control / signaling right was a little more difficult.
straight cable = pin to pin
crossed cable = null modem = swapped pins
The phrase "null modem" comes from no modems or the configuration
that allows two singular ports to be connected, this cable would
cross the receive and transmit pins, and some would call it a cross
over cable. A null modem cable would be used to connect two computers
together and a program like kermit used to transfer files.
Yep.. DTE cable to DCE communications medium(phoneline) DCE to DTE
DCE == Modem (e.g. a Bell 202 or 212, for instance)
There were the flow control (RTS/CTS) used to turn around a half duplex
link. And, there are also the secondary transmit and receive (for a low
rate reverse channel). If you were receiving data from the link (DCE),
you'd assert RTS, and when the modem had switched, it would tell you CTS,
and off you'd go. (fancy modems used the reverse channel to send the
request to the far end, which would acknowledge... others just use a fixed
time delay) There are also pins for the clock (since some of these modems
were used on synchronous data links).
the "crossover" occured in the DCE to DCE link (that is, you'd transmit
from one DCE to the other DCE's receiver)...
the nominal cable between DTE and DCE was straight through. With no real
convention on male/female.. most devices had female sockets, and the cables
usually were male male plugs. IBM PCs had male on the chassis for DTE, as
did some PDT-110 (VT-100/LSI-11 smart terminals), but most other terminals
(the LSI ADM-x, Hazeltines, etc.) all seemed to have female, as did the TI
800 series printer/terminals.
So, a "null modem" was a cable that emulated the DCE to DCE connection..
there are/were various strategies on how sophisticated the reverse is..
do you also send the secondary channel? What about clocks? Most folks
ignored all that and used RTS/CTS
Or you strap RTS to CTS on your side, the other side does the same.
I think the phrase "standard cable" which could be null or straight
depending on the use is the confusing part.
Phone cables RJ11 and RJ45 swap the wires which is standard. Network
cables match the wires with the same color always on the right which
is standard. But even when a phone cable is standard it is not
interchangeable with a standard network cable. Again we have a need
for cross as well as straight network cables.
And, to make things worse, there are different "pair" arrangements.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
--
Steve Rooke - ZL3TUV & G8KVD
A man with one clock knows what time it is;
A man with two clocks is never quite sure.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
