I've made some investigations and re-confirmed my earlier findings on the FE-5680B I have.
It locks from cold in under five minutes and runs at approximately 700mA steady with the expected PPS signal on the output connector when locked. The particular 5680 I have has a Hi Density 15p male connector on the output and uses a single 15V supply, part number FE5680B UN 77672. The device does not have the optional DDS daughterboard which means that it's not usable as a programmable signal source as it stands (but see later). For approximately six seconds after power is applied a 10MHz signal available on the output connector, this signal comes directly from the XC9572 CPLD via a filter network and appears to be a clean sine wave. The 10MHz signal seems to be 'switched off' by some event in the unit, I don't yet know if this is in response to an event or just a timed shutdown but power cycling the unit re-enables the 10MHz output for a further six seconds. It doesn't appear to be related to rubidium lock as it takes consdierably longer than six seconds to lock. There is a solid 30MHz signal inside the unit, stable once the rubidium has locked and the PPS output is also available once locked. Other observations show that the MAX3232 serial driver chip is missing and in it's place there is a tiny 8 pin device marked M09 or MO9 which is connected to the TXD/RXD pins on the output connector and the TXD/RXD pins on the 80C323 CPU. I'd be very interested in suggestions as to the part number of that device, it may yield clues as to the communication method needed. Attempts to communicate with it via a terminal program have given no responses at several 'standard' baud rates. Voltage levels are LVTTL. I'm wary of applying 5V to any of the pins on the interface connector directly and probing them with 3.3v via a 10K resistor has made no difference to any of the signals I can monitor (30MHz, PPS etc.) with the exception of pin 13 which I *think* is reset, obviously this causes the frequencies to skew for a few seconds until reset is completed. My intent is to use the 30MHz signal from the CPLD to clock a DDS chip (probably one of the eBay DDS modules) that's controlled by a PIC chip (I already have code to run a DDS VFO I developed earlier this and late last year. Hopefully this will be small enough to fit inside the casing though I don't see a problem with bringing the 30MHz signal out if necessary. My apologies if this is outside of the scope of this list, I will also be writing up my findings and experiments with this standard on my blog if anyone is interested? On 26 September 2015 at 11:23, Bryan _ <bpl...@outlook.com> wrote: > Thanks Hal, that's interesting, will try and see how far I can get. > -=Bryan=- > > > To: time-nuts@febo.com > > From: hmur...@megapathdsl.net > > Date: Fri, 25 Sep 2015 23:40:40 -0700 > > CC: hmur...@megapathdsl.net > > Subject: Re: [time-nuts] FE-5680B Rubidium and DDS > > > > > > > I as well wish there was a quick way of converting it back to 10Mhz. I > am > > > sure it can be done, just not sure how or where to look > > > > If the 10 MHz is visible for a second or two, there is probably a gate to > > turn it on/off. If I wanted 10 MHz, I'd open it up and trace the wire > back. > > If it goes to a gate, you might be able to lift the pin for the other > input > > and wire it hi/low. There is a good chance it goes to a FPGA where you > can't > > get at the gate. > > > > > > > > > > -- > > These are my opinions. I hate spam. > > > > > > > > _______________________________________________ > > time-nuts mailing list -- time-nuts@febo.com > > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- time-nuts@febo.com > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > -- Clint. *No trees were harmed in the sending of this mail. However, a large number of electrons were greatly inconvenienced.* _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
