Back in the day, companies, like Vibrograf, Greiner, Elna, L&R, all made timing machines that were based on the same principles.
The machines used a crystal, or tuning fork frequency reference, and divided it down for the various standard (and not so standard) watch beat rates. The divided reference signal was used to turn a synchronous motor, which rotated a drum which had a single turn loop of wire wound around it, in the fashion of a "one turn per drum width" screw thread. The watch's movement was clamped into a mount that had a piezoelectric element, usually a rochelle salt crystal, that turned the small vibrations into an electric representation that was fed to a chain of amplifiers, filtered to amplify only the audible component until it was large enough to trigger a tiny little thyratron tube. The thyratron tube was set so that when the impulse exceeded a variable threshold, it would fire, and would discharge a capacitor into a solenoid for an instant, and pull in the armature that caused a metal "bale", that was as wide as the drum, to strike the wire that is wrapped around the rotating drum. Because this wire essentially proceeded along the drum as it rotated, the intersection of the wire, and the bale formed a scanning element, not unlike the beam on a CRT oscilloscope. To record the impulse, a paper tape was fed between the rotating drum, a typewriter ribbon, and the metal bale. When the metal bale "ticked", it pushed the ribbon against the paper, and the travel was stopped by the rotating wire wrapped on the drum, and an ink mark was made. Ok, why all this complexity? The idea was to, tick-by-tick, record the difference between the watch movement's escapement's noise and the smooth flow of time embodied by the crystal/tuning fork/dividers, etc.. By adjusting the gain of the microphone's amplifier stage, and as a result, the threshold of the printer, the watchmaker could observe quiet repeating noises all the way down to the pretty noisy tick of the watch. When you look at these actual traces, your squishy ware's DSP can easily see the slope of the group of traces, which is the rate of the watch, and any rhythmic variations of the individual "ticks" recorded on the paper. You can see things like irregular spacing of the teeth on the escapement wheel, and irregular spacing of many of the later wheels and pinions. By adjusting the gain of the amplifier stages, and the resulting shift in threshold, you can select out noises of different loudnesses. And the speed of the thyratron, and charged capacitor allowed multiple strikes of the bale during each tick. You can see the noise made by the impulse jewel touching the tuning fork, and the noise made by the pallet jewels touching the escapement wheel... Lots of very interesting things that indicate the quality of the movement, and the state of its lubrication... as well as a nearly instantaneous indication of the rate of the watch, as it sits in the various "positions" (dial up, dial down, pendant up, down, right left...) All of this from the feverish minds of horologists back at the dawn of the vacuum tube. I would suggest that any programming you use for your tools do similar things. -Chuck Harris Andrea Baldoni wrote:
Hello! I decided to do some experiments with mechanical clocks, so I worked a little on picking up escapement ticking sound, with the idea of processing it and obtaining a "clean" digital pulse to feed a counter. So far, I have not yet been able to find the best way to obtain a digital pulse, but I have already built the preamp for the piezoelectrick pickup, that I used to feed the mic input of a PC sound card for spectrum analysis. The timing could eventually be done in software because the whole idea of measuring watches by picking up their noise almost surely doesn't allow high resolution anyway, but I will plan to try hardware solutions as well in the future. I hope to be able to measure the jitter of the clock, but it will be very hard. In the meantime, with the free software Biburo you can download here http://tokeiyade.michikusa.jp you can regulate your wrist watch. Best regards, Andrea Baldoni _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
_______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.