Hi
Here it is. Thank you for helping us.
[EMAIL PROTECTED]:/opt/tinyos-2.x/apps/tests/deluge/Blink$ ./burn
/dev/ttyUSB0 micaz
rm -rf build
rm -rf _TOSSIMmodule.so TOSSIM.pyc TOSSIM.py
============================ Compile and load Blink
============================
mkdir -p build/micaz
tos-storage-at45db /opt/tinyos-2.x/tos/platforms/micaz
<volumes-at45db.xml>build/micaz/StorageVolumes.h || rm -f
build/micaz/StorageVolumes.h
compiling BlinkAppC to a micaz binary
ncc -o build/micaz/main.exe -Os -finline-limit=100000 -Wall -Wshadow
-Wnesc-all -target=micaz -fnesc-cfile=build/micaz/app.c -board=micasb
-Ibuild/micaz -DDELUGE_BASESTATION -DDELUGE_BASESTATION -DDELUGE
-I/opt/tinyos-2.x/tos/lib/net -I/opt/tinyos-2.x/tos/lib/net/Deluge
-I/opt/tinyos-2.x/tos/lib/net/Deluge/FlashVolumeManager
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/avr
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/micaz
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/mica2
-DIDENT_PROGRAM_NAME=\"BlinkAppC\" -DIDENT_USER_ID=\"xubuntos\"
-DIDENT_HOSTNAME=\"xubuntos-tinyos\" -DIDENT_USER_HASH=0x00f95284L
-DIDENT_UNIX_TIME=0x47157635L -DIDENT_UID_HASH=0x94dcc068L
-fnesc-dump=wiring -fnesc-dump='interfaces(!abstract())'
-fnesc-dump='referenced(interfacedefs, components)'
-fnesc-dumpfile=build/micaz/wiring-check.xml BlinkAppC.nc -lm
compiled BlinkAppC to build/micaz/main.exe
30448 bytes in ROM
925 bytes in RAM
avr-objcopy --output-target=srec build/micaz/main.exe build/micaz/main.srec
avr-objcopy --output-target=ihex build/micaz/main.exe build/micaz/main.ihex
writing TOS image
cp build/micaz/main.srec build/micaz/main.srec.out
installing micaz binary using mib510
uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xda -dpart=ATmega128
--wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out
Firmware Version: 1.8
Atmel AVR ATmega128 is found.
Uploading: flash
Fuse High Byte set to 0xda
Fuse Extended Byte set to 0xff
rm -f build/micaz/main.exe.out build/micaz/main.srec.out
installing micaz bootloader using mib510
uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xda -dpart=ATmega128
--wr_fuse_e=ff --upload if=/opt/tinyos-2.x
/tos/lib/tosboot/build/micaz/main.ihex
Firmware Version: 1.8
Atmel AVR ATmega128 is found.
Uploading: flash
Fuse High Byte set to 0xda
Fuse Extended Byte set to 0xff
+-------------------------------------------------------+
| |
| At this point the first led (red) should be blinking. |
| |
| Press ENTER to continue... |
| |
+-------------------------------------------------------+
============================= Compile a new Blink
==============================
mkdir -p build/micaz
compiling BlinkAppC to a micaz binary
ncc -o build/micaz/main.exe -Os -finline-limit=100000 -Wall -Wshadow
-Wnesc-all -target=micaz -fnesc-cfile=build/micaz/app.c -board=micasb
-Ibuild/micaz -DBLINK_REVERSE -DDELUGE_BASESTATION -DDELUGE_BASESTATION
-DDELUGE -I/opt/tinyos-2.x/tos/lib/net -I/opt/tinyos-2.x/tos/lib/net/Deluge
-I/opt/tinyos-2.x/tos/lib/net/Deluge/FlashVolumeManager
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/avr
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/micaz
-I/opt/tinyos-2.x/tos/lib/net/Deluge/extra/mica2
-DIDENT_PROGRAM_NAME=\"BlinkAppC\" -DIDENT_USER_ID=\"xubuntos\"
-DIDENT_HOSTNAME=\"xubuntos-tinyos\" -DIDENT_USER_HASH=0x00f95284L
-DIDENT_UNIX_TIME=0x47157661L -DIDENT_UID_HASH=0xcba6eb76L
-fnesc-dump=wiring -fnesc-dump='interfaces(!abstract())'
-fnesc-dump='referenced(interfacedefs, components)'
-fnesc-dumpfile=build/micaz/wiring-check.xml BlinkAppC.nc -lm
compiled BlinkAppC to build/micaz/main.exe
30448 bytes in ROM
925 bytes in RAM
avr-objcopy --output-target=srec build/micaz/main.exe build/micaz/main.srec
avr-objcopy --output-target=ihex build/micaz/main.exe build/micaz/main.ihex
writing TOS image
=============================== Upload the image
===============================
Pinging node ...
ERROR: Unable to retrieve image information over serial
+----------------------------------------------------------------+
| |
| In the next step the following things will take place: |
| - the mote will be rebooted |
| - all the leds will blink for some time as the |
| reprogramming by tosboot takes place. |
| - a fading of the leds will indicate the exiting from tosboot. |
| - the mote should start blinking the 3rd led (blue/yellow). |
| |
| Press ENTER to continue... |
| |
+----------------------------------------------------------------+
=========================== Reboot the base station
============================
ERROR: Unable to retrieve image information over serial
2007/10/17, Chieh-Jan (Mike) Liang <[EMAIL PROTECTED]>:
>
> Hi Luis,
>
> Could you please send me your screen output from ".burn /dev/ttyUSB0
> micaz"?
>
> Thank you
>
> Mike
>
> Luis Miguel López Ramos wrote:
> > Hi all
> >
> > I'm experiencing a problem running the apps/tests/deluge/Blink
> > application. I'm using XubunTOS over a VMWare Player, my mote is a
> > micaz and my board is an USB mib510, so I type:
> >
> > ./burn /dev/ttyUSB0 micaz
> >
> > The first version of Blink executes normally, and then, when burn says
> > 'Pinging node' it seems not to find any mote and after a while it says
> > 'Unable to retrieve information over serial'. The mote neither reboots
> > nor does anything different from the first blink.
> >
> > Has anybody else found this problem?
> >
> > Thank you very much
> > Luis Miguel Lopez
> > Universidad Rey Juan Carlos, Fuenlabrada, Madrid (Spain)
> > _______________________________________________
> > Tinyos-help mailing list
> > Tinyos-help@Millennium.Berkeley.EDU
> > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
>
_______________________________________________
Tinyos-help mailing list
Tinyos-help@Millennium.Berkeley.EDU
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
