Ladies and Gents,
Could someone give me some advice or a solution to a problem I am having
writing to the sensor nodes?? I have tried two commands:make mica2 install
and make mica2 install mib510,/dev/ttyS0.. The two errors I am receiving is
located below... If you guys have experience this before please give feedback
as I am need of help...
Thanks,
1st Scenario
[EMAIL PROTECTED] Blink]$ make mica2 install
mkdir -p build/mica2
compiling BlinkAppC to a mica2 binary
ncc -o build/mica2/main.exe -Os -finline-limit=100000 -Wall -Wshadow
-DDEF_TOS_AM_GROUP=0x7d -Wnesc-all -target=mica2
-fnesc-cfile=build/mica2/app.c -board=micasb -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/mica2/wiring-check.xml BlinkAppC.nc -lm
compiled BlinkAppC to build/mica2/main.exe
2688 bytes in ROM
57 bytes in RAM
avr-objcopy --output-target=srec build/mica2/main.exe build/mica2/main.srec
avr-objcopy --output-target=ihex build/mica2/main.exe build/mica2/main.ihex
writing TOS image
cp build/mica2/main.srec build/mica2/main.srec.out
installing mica2 binary with dapa
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff --erase
pulse
Atmel AVR ATmega128 is found.
Erasing device ...
pulse
Reinitializing device
Atmel AVR ATmega128 is found.
Fuse High Byte set to 0xd9
Fuse Extended Byte set to 0xff
sleep 1
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff --upload
if=build/mica2/main.srec.out
pulse
Atmel AVR ATmega128 is found.
Uploading: flash
Fuse High Byte set to 0xd9
Fuse Extended Byte set to 0xff
sleep 1
uisp -dprog=dapa --wr_fuse_h=0xd9 -dpart=ATmega128 --wr_fuse_e=ff --verify
if=build/mica2/main.srec.out
pulse
Atmel AVR ATmega128 is found.
Verifying: flash
flash error at address 0x0: file=0x0c, mem=0xff
flash error at address 0x1: file=0x94, mem=0xff
flash error at address 0x2: file=0x49, mem=0xff
flash error at address 0x3: file=0x00, mem=0xff
flash error at address 0x4: file=0x0c, mem=0xff
flash error at address 0x5: file=0x94, mem=0xff
flash error at address 0x6: file=0x66, mem=0xff
flash error at address 0x7: file=0x00, mem=0xff
flash error at address 0x8: file=0x0c, mem=0xff
flash error at address 0x9: file=0x94, mem=0xff
2nd Scenario
[EMAIL PROTECTED] Blink]$ make mica2 install mib510,/dev/ttyS0
mkdir -p build/mica2
compiling BlinkAppC to a mica2 binary
ncc -o build/mica2/main.exe -Os -finline-limit=100000 -Wall -Wshadow
-DDEF_TOS_AM_GROUP=0x7d -Wnesc-all -target=mica2
-fnesc-cfile=build/mica2/app.c -board=micasb -fnesc-dump=wiring
-fnesc-dump='interfaces(!abstract())' -fnesc-dump='referenced(interfacedefs,
components)' -fnesc-dumpfile=build/mica2/wiring-check.xml BlinkAppC.nc -lm
compiled BlinkAppC to build/mica2/main.exe
2688 bytes in ROM
57 bytes in RAM
avr-objcopy --output-target=srec build/mica2/main.exe build/mica2/main.srec
avr-objcopy --output-target=ihex build/mica2/main.exe build/mica2/main.ihex
writing TOS image
cp build/mica2/main.srec build/mica2/main.srec.out
installing mica2 binary using mib510
uisp -dprog=mib510 -dserial=/dev/ttyS0 --wr_fuse_h=0xd9 -dpart=ATmega128
--wr_fuse_e=ff --erase --upload if=build/mica2/main.srec.out
Programmer is not responding.
make: *** [program] Error 2
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
