On Fri, Jun 3, 2011 at 1:08 PM, [email protected] <[email protected]>wrote:
> Hi John, I was definitely using a different tos version. > I'm using the one installed by this tutorial: > http://docs.tinyos.net/tinywiki/index.php/Installing_TinyOS_2.1#Two-step_install_on_your_host_OS_with_Debian_packages > There is no IPForwardingEngine or IPNeighborDiscovery. > > I've just got the code from the googlecode svn > http://tinyos-main.googlecode.com/svn/trunk > I can see that there are several modifications and I will go through the > new code trying to intercept the packet before forward it so many thanks for > your advise. > You definitely want to be working off the svn trunk (which is what you mention immediately above). > > I've also noticed that the IPBasestation, UDPEcho and TCPEcho are broken in > the svn code. Could anybody tell me if it's the right repository to use? Is > it a stable version? > I'm pretty sure you want to be looking at the blip-rpl-devel branch. BLIP is in current development and lots of changes are happening with it. That work is happening on the blip-rpl-devel branch. You should double check with Stephen though. eric > > > Many thanks > > > Davide > > > > On 3 Jun 2011, at 19:02, JeongGil Ko (John) wrote: > > > When the packet needs to get forwarded the reconstructed packet first > reaches the IPForwardingEngineP.nc via recv() signals and the packet's next > hop is determined at this point. Once the next hop is determined the packet > flows through IPNeighborDiscovery and IPDispatch once again. > > > > -John > > > > On Jun 3, 2011, at 1:51 PM, [email protected] wrote: > > > >> Hi again, > >> > >> When a packet has to be forwarded, does IPDispatch signal the IP.recv ? > >> > >> I don't have already a good knowledge of the Blip stack but it seems to > me that it calls the Ieee154Send.send() without signaling the IP.recv. Am I > wrong? > >> > >> Manay thanks > >> > >> Davide > >> > >> > >> On 3 Jun 2011, at 11:37, [email protected] wrote: > >> > >>> Hi all, > >>> > >>> I'm using the Blip stack and I'm trying to implement a kind of data > aggregation along the route when using Blip. > >>> > >>> Is it there any component that allow me to access the UDP payload of a > UDP that have to be forwarded? > >>> > >>> Many thanks > >>> > >>> > >>> > >>> Davide > >>> _______________________________________________ > >>> Tinyos-help mailing list > >>> [email protected] > >>> > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> > >> > >> _______________________________________________ > >> Tinyos-help mailing list > >> [email protected] > >> > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> > > > > ------ > > JeongGil Ko (John) > > Ph.D. Student > > Department of Computer Science > > Johns Hopkins University > > http://www.cs.jhu.edu/~jgko > > > > > > _______________________________________________ > > Tinyos-help mailing list > > [email protected] > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > > > _______________________________________________ > Tinyos-help mailing list > [email protected] > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > -- Eric B. Decker Senior (over 50 :-) Researcher
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
