Moin, Am Sa., 3. Apr. 2021 um 11:33 Uhr schrieb Florian Knodt <lug...@adlerweb.info>: > > Moin, > > On 03.04.2021 11:28, Thorsten Kern wrote: > > Kann ich von einen hardwaredefekt ausgehen > > Ich würde erst mal mit smartctl -a /dev/sda die Parameter der Platte > anschauen. Dort ist z.B. zu sehen ob es defekte Blöcke (=Platte kaputt) > oder Übertragungsfehler (Kabel nicht richtig drin?) die Ursache sind.
Hier die Ausgabe: smartctl 6.6 2017-11-05 r4594 [armv6l-linux-5.4.83+] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Scorpio Blue Serial ATA (AF) Device Model: WDC WD6400BPVT-22HXZT1 Serial Number: WD-WXA1A11E2110 LU WWN Device Id: 5 0014ee 6ab94e6a1 Firmware Version: 01.01A01 User Capacity: 640.135.028.736 bytes [640 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sat Apr 3 12:12:55 2021 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART Status command failed: Die Wartezeit f_r die Verbindung ist abgelaufen SMART overall-health self-assessment test result: PASSED Warning: This result is based on an Attribute check. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15960) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 157) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x7035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 205 166 021 Pre-fail Always - 741 4 Start_Stop_Count 0x0032 094 094 000 Old_age Always - 6654 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 073 073 000 Old_age Always - 20327 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 096 096 000 Old_age Always - 4180 191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 1632878 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 268 193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 912395 194 Temperature_Celsius 0x0022 121 076 000 Old_age Always - 26 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 20327 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [Ende Ausgabe] Trotz Suchmaschinenrecherche kann ich nicht erkennen, was mir diese Ausgabe sagen soll. Wer kann mir diese Ausgabe ein bissle erläutern? Danke im vorraus Gruß Thorsten