according to gvb's suggestion, polishing for the doc.

Signed-off-by: Jerry Van Baren <[EMAIL PROTECTED]>
Signed-off-by: Dave Liu <[EMAIL PROTECTED]>
---
 doc/README.sata |   24 ++++++++++++------------
 1 files changed, 12 insertions(+), 12 deletions(-)

diff --git a/doc/README.sata b/doc/README.sata
index 168dc7f..d0ce667 100644
--- a/doc/README.sata
+++ b/doc/README.sata
@@ -1,11 +1,11 @@
 1. SATA usage in U-boot
 
-       Two ways to operate the hard disk
+       There are two ways to operate the hard disk
 
-       * Raw read/write block from/to SATA hard disk;
-       * ext2load read file from ext2 filesytem in hard disk
+       * Read/write raw blocks from/to SATA hard disk
+       * ext2load to read a file from ext2 file system
 
-1.0 How to know the information of SATA hard disk?
+1.0 How to read the SATA hard disk's information?
 
        => sata info
 
@@ -14,11 +14,12 @@ SATA device 0: Model: ST3320620AS Firm: 3.AAD Ser#:         
4QF01ZTN
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)
 
-1.1 How to save the kernel, filesystem, dtb to SATA hard disk with raw?
+1.1 How to raw write the kernel, file system, dtb to a SATA hard disk?
 
-       Notes: 0x1000 sectors = 2 MBytes
+       Notes: Hard disk sectors are normally 512 bytes, so
+               0x1000 sectors = 2 MBytes
 
-       wirte kernel
+       write kernel
        => tftp 40000 /tftpboot/uImage.837x
        => sata write 40000 0 2000
 
@@ -30,7 +31,7 @@ SATA device 0: Model: ST3320620AS Firm: 3.AAD Ser#:           
4QF01ZTN
        => tftp 40000 /tftpboot/mpc837xemds.dtb
        => sata write 40000 a000 1000
 
-1.2 How to read the kernel, filesystem, dtb from SATA hard disk with raw?
+1.2 How to raw read the kernel, file system, dtb from a SATA hard disk?
 
        load kernel
        => sata read 200000 0 2000
@@ -44,11 +45,10 @@ SATA device 0: Model: ST3320620AS Firm: 3.AAD Ser#:         
4QF01ZTN
        boot
        => bootm 200000 1000000 2000000
 
-1.3 How to load image from ext2 filesystem in U-boot?
+1.3 How to load an image from an ext2 file system in U-boot?
 
-       U-boot doesn't support ext2 write to hard disk, so
-       you have to write the image to hard disk under Linux env,
-       before you load image from ext2 filesystem.
+       U-boot doesn't support writing to an ext2 file system, so the
+       files must be written by other means (e.g. linux).
 
        => ext2ls sata 0:1 /
        <DIR>       4096 .
-- 
1.5.4.rc4




-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
U-Boot-Users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/u-boot-users

Reply via email to