Stefan Roese wrote: > I just ran into a problem with current U-Boot on Kilauea and device tree > enabled Linux kernel (arch/powerpc). After updating U-Boot the kernel doesn't > boot anymore: > > => run net_nfs_fdt > Waiting for PHY auto negotiation to complete... done > ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) > Using ppc_4xx_eth0 device > TFTP from server 10.0.0.152; our IP address is 10.0.0.182 > Filename 'kilauea/uImage'. > Load address: 0x200000 > Loading: ################################################################# > ####################### > done > Bytes transferred = 1288707 (13aa03 hex) > ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) > Using ppc_4xx_eth0 device > TFTP from server 10.0.0.152; our IP address is 10.0.0.182 > Filename 'kilauea/kilauea.dtb'. > Load address: 0x400000 > Loading: # > done > Bytes transferred = 8000 (1f40 hex) > ## Booting kernel from Legacy Image at 00200000 ... > Image Name: Linux-2.6.25-rc7-next-20080327-d > Created: 2008-03-27 13:51:18 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 1288643 Bytes = 1.2 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > ERROR: image overwritten - must RESET the board to recover. > > > Before updating U-Boot I am able to boot exactly this kernel/dtb combination > without problems: > > => run net_nfs_fdt > Waiting for PHY auto negotiation to complete... done > ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) > Using ppc_4xx_eth0 device > TFTP from server 10.0.0.152; our IP address is 10.0.0.182 > Filename 'kilauea/uImage'. > Load address: 0x200000 > Loading: ################################################################# > ####################### > done > Bytes transferred = 1288707 (13aa03 hex) > ENET Speed is 1000 Mbps - FULL duplex connection (EMAC0) > Using ppc_4xx_eth0 device > TFTP from server 10.0.0.152; our IP address is 10.0.0.182 > Filename 'kilauea/kilauea.dtb'. > Load address: 0x400000 > Loading: # > done > Bytes transferred = 8000 (1f40 hex) > ## Booting image at 00200000 ... > Image Name: Linux-2.6.25-rc7-next-20080327-d > Created: 2008-03-27 13:51:18 UTC > Image Type: PowerPC Linux Kernel Image (gzip compressed) > Data Size: 1288643 Bytes = 1.2 MB > Load Address: 00000000 > Entry Point: 00000000 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > Booting using the fdt at 0x400000 > Using Kilauea machine description > ... > > > Any ideas?
The image got overwritten during decompression. Try loading the image at a higher address. Regards, Bartlomiej ------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace _______________________________________________ U-Boot-Users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/u-boot-users
