I realize this could be posted to the linuxppc-dev also, but my kernel
is running fine so I think it's a u-boot to kernel interface problem. I
am able to pass a device tree to the kernel and get it to boot fine, and
using NFS root also.
I can't get it to find my initrd ramdisk is my problem. A kernel image,
zImage.initrd, works with the ramdisk image, so I think everything is
setup ok with the kernel. I'm using a uImage and using mkimage on my
ramdisk also for u-boot.
I realize it could be that I'm just loading the images in the RAM such
that when the kernel gets uncompressed it stomps on the ram disk. I have
tried moving to other addresses without any luck. When I look in memory
where the ram disk was loaded by uboot, I can see the image fine after
the kernel has paniced because it didn't find the root file system.
Is there something basic that I'm missing?
Thanks, appreciate any help,
John
=> bootm 0x1c00000 0x1800000 0x1000000
## Booting image at 01c00000 ...
Image Name: Linux-2.6.26-rc8
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1536987 Bytes = 1.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at 01800000 ...
Image Name:
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 1507104 Bytes = 1.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Booting using the fdt at 0x1000000
Loading Ramdisk to 0fd35000, end 0fea4f20 ... OK
Loading Device Tree to 007fc000, end 007fefff ... OK
Loading Device Tree to 007fa000, end 007fcfff ... OK
Using Xilinx Virtex machine description
Linux version 2.6.26-rc8 ([EMAIL PROTECTED]) (gcc version 4.0.0 (DENX
ELDK 4.1 4.0.0)) #4 PREEMPT Tue Jul 8 14
:45:07 PDT 2008
Zone PFN ranges:
DMA 0 -> 131072
Normal 131072 -> 131072
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 131072
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
130048
Kernel command line: console=ttyS0 ip=on root=/dev/ram
Xilinx intc at 0xD0020200 mapped to 0xfdfff200
PID hash table entries: 2048 (order: 11, 8192 bytes)
clocksource: timebase mult[c800000] shift[22] registered
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 514432k/524288k available (3024k kernel code, 9332k reserved,
128k data, 149k bss, 156k init)
Mount-cache hash table entries: 512
device-tree: Duplicate name in /, renamed to "chosen#1"
net_namespace: 624 bytes
NET: Registered protocol family 16
PCI: Probing PCI hardware
NET: Registered protocol family 2
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
msgmni has been set to 1005
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
d0000000.serial: ttyS0 at MMIO 0xd0000003 (irq = 16) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
Device Tree Probing 'ethernet'
xilinx_lltemac 91200000.ethernet: MAC address is now 2: 0: 0: 0: 0: 0
xilinx_lltemac 91200000.ethernet: XLlTemac: using DMA mode.
XLlTemac: DCR address: 0x80
XLlTemac: buffer descriptor size: 32768 (0x8000)
XLlTemac: Allocating DMA descriptors with kmalloc<6>XLlTemac:
(buffer_descriptor_init) phy: 0x1fa08000, virt:
0xdfa08000, size: 0x8000
XTemac: PHY detected at address 7.
eth0: Dropping NETIF_F_SG since no checksum feature.
xilinx_lltemac 91200000.ethernet: eth0: Xilinx TEMAC at 0x91200000
mapped to 0xE100E000, irq=17
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Device Tree Probing 'i2c'
d0020000.i2c #0 at 0xD0020000 mapped to 0xE1010000, irq=20
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
eth0: XLlTemac: Options: 0x3fa
eth0: XLlTemac: allocating interrupt 19 for dma mode tx.
eth0: XLlTemac: allocating interrupt 18 for dma mode rx.
eth0: XLlTemac: speed set to 100Mb/s
eth0: XLlTemac: Send Threshold = 24, Receive Threshold = 4
eth0: XLlTemac: Send Wait bound = 254, Receive Wait bound = 254
Sending DHCP requests .., OK
IP-Config: Got DHCP answer from 149.199.109.235, my address is
172.16.40.12
IP-Config: Complete:
device=eth0, addr=172.16.40.12, mask=255.255.255.0,
gw=172.16.40.254,
host=172.16.40.12, domain=xilinx.com public.xilinx.com
xlnx.xilinx.com public.xsj.xilinx., nis-domain=xil
inx.com,
bootserver=149.199.109.235, rootserver=149.199.109.235,
rootpath=/tmp
List of all partitions:
No filesystem could mount root, tried: ext2 cramfs msdos vfat romfs
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(1,0)
Rebooting in 180 seconds..
This email and any attachments are intended for the sole use of the named
recipient(s) and contain(s) confidential information that may be proprietary,
privileged or copyrighted under applicable law. If you are not the intended
recipient, do not read, copy, or forward this email message or any attachments.
Delete this email message and any attachments immediately.
-------------------------------------------------------------------------
Sponsored by: SourceForge.net Community Choice Awards: VOTE NOW!
Studies have shown that voting for your favorite open source project,
along with a healthy diet, reduces your potential for chronic lameness
and boredom. Vote Now at http://www.sourceforge.net/community/cca08
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users
