Hi Piotr, On 01/03/2013 04:31 PM, Piotr Wilczek wrote: > This patch add pinmux settings for Exynos4 for mmc0 and mmc2 Didn't consider about the mmc4? I know that exynos4 can be used mmc4 for eMMC.
Best Regards, Jaehoon Chung > > Signed-off-by: Piotr Wilczek <p.wilc...@samsung.com> > Signed-off-by: Kyungmin Park <kyungmin.p...@samsung.com> > CC: Minkyu Kang <mk7.k...@samsung.com> > CC: Albert ARIBAUD <albert.u.b...@aribaud.net> > --- > arch/arm/cpu/armv7/exynos/pinmux.c | 45 > ++++++++++++++++++++++++++++++++++++ > 1 file changed, 45 insertions(+) > > diff --git a/arch/arm/cpu/armv7/exynos/pinmux.c > b/arch/arm/cpu/armv7/exynos/pinmux.c > index 20a4b84..ee58dac 100644 > --- a/arch/arm/cpu/armv7/exynos/pinmux.c > +++ b/arch/arm/cpu/armv7/exynos/pinmux.c > @@ -370,6 +370,43 @@ static void exynos4_i2c_config(int peripheral, int flags) > } > } > > +static int exynos4_mmc_config(int peripheral, int flags) > +{ > + struct exynos4_gpio_part2 *gpio2 = > + (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); > + struct s5p_gpio_bank *bank, *bank_ext; > + int i; > + > + switch (peripheral) { > + case PERIPH_ID_SDMMC0: > + bank = &gpio2->k0; > + bank_ext = &gpio2->k1; > + break; > + case PERIPH_ID_SDMMC2: > + bank = &gpio2->k2; > + bank_ext = &gpio2->k3; > + break; > + default: > + return -1; > + } > + for (i = 0; i < 7; i++) { > + if (i == 2) > + continue; > + s5p_gpio_cfg_pin(bank, i, GPIO_FUNC(0x2)); > + s5p_gpio_set_pull(bank, i, GPIO_PULL_NONE); > + s5p_gpio_set_drv(bank, i, GPIO_DRV_4X); > + } > + if (flags & PINMUX_FLAG_8BIT_MODE) { > + for (i = 3; i < 7; i++) { > + s5p_gpio_cfg_pin(bank_ext, i, GPIO_FUNC(0x3)); > + s5p_gpio_set_pull(bank_ext, i, GPIO_PULL_NONE); > + s5p_gpio_set_drv(bank_ext, i, GPIO_DRV_4X); > + } > + } > + > + return 0; > +} > + > static int exynos4_pinmux_config(int peripheral, int flags) > { > switch (peripheral) { > @@ -383,6 +420,14 @@ static int exynos4_pinmux_config(int peripheral, int > flags) > case PERIPH_ID_I2C7: > exynos4_i2c_config(peripheral, flags); > break; > + case PERIPH_ID_SDMMC0: > + case PERIPH_ID_SDMMC2: > + return exynos4_mmc_config(peripheral, flags); > + case PERIPH_ID_SDMMC1: > + case PERIPH_ID_SDMMC3: > + case PERIPH_ID_SDMMC4: > + printf("SDMMC device %d not implemented\n", peripheral); > + return -1; > default: > debug("%s: invalid peripheral %d", __func__, peripheral); > return -1; > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot