This adds support to the LAN9512 chip included in the board and extend
the environment to easy netboot use.

Signed-off-by: Otavio Salvador <ota...@ossystems.com.br>
---
Changes in v2:
- Remove extra newline

 include/configs/mx23_olinuxino.h | 39 ++++++++++++++++++++++++++++++++++++---
 1 file changed, 36 insertions(+), 3 deletions(-)

diff --git a/include/configs/mx23_olinuxino.h b/include/configs/mx23_olinuxino.h
index e081c49..dfba0fc 100644
--- a/include/configs/mx23_olinuxino.h
+++ b/include/configs/mx23_olinuxino.h
@@ -55,11 +55,13 @@
 #define        CONFIG_DOS_PARTITION
 
 #define        CONFIG_CMD_CACHE
+#define        CONFIG_CMD_DHCP
 #define        CONFIG_CMD_EXT2
 #define        CONFIG_CMD_FAT
 #define        CONFIG_CMD_GPIO
 #define        CONFIG_CMD_LED
 #define        CONFIG_CMD_MMC
+#define        CONFIG_CMD_NET
 #define        CONFIG_CMD_USB
 
 /*
@@ -150,6 +152,12 @@
 #define        CONFIG_USB_STORAGE
 #endif
 
+/* Ethernet */
+#ifdef CONFIG_CMD_NET
+#define        CONFIG_USB_HOST_ETHER
+#define        CONFIG_USB_ETHER_SMSC95XX
+#endif
+
 /*
  * Boot Linux
  */
@@ -191,6 +199,7 @@
        "fdt_file=imx23-olinuxino.dtb\0" \
        "fdt_addr=0x41000000\0" \
        "boot_fdt=try\0" \
+       "ip_dyn=yes\0" \
        "mmcdev=0\0" \
        "mmcpart=2\0" \
        "mmcroot=/dev/mmcblk0p3 rw rootwait\0" \
@@ -216,6 +225,31 @@
                        "fi; " \
                "else " \
                        "bootm; " \
+               "fi;\0" \
+       "netargs=setenv bootargs console=${console_mainline},${baudrate} " \
+               "root=/dev/nfs " \
+               "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
+       "netboot=echo Booting from net ...; " \
+               "usb start; " \
+               "run netargs; " \
+               "if test ${ip_dyn} = yes; then " \
+                       "setenv get_cmd dhcp; " \
+               "else " \
+                       "setenv get_cmd tftp; " \
+               "fi; " \
+               "${get_cmd} ${uimage}; " \
+               "if test ${boot_fdt} = yes; then " \
+                       "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
+                               "bootm ${loadaddr} - ${fdt_addr}; " \
+                       "else " \
+                               "if test ${boot_fdt} = try; then " \
+                                       "bootm; " \
+                               "else " \
+                                       "echo WARN: Cannot load the DT; " \
+                               "fi;" \
+                       "fi; " \
+               "else " \
+                       "bootm; " \
                "fi;\0"
 
 #define CONFIG_BOOTCOMMAND \
@@ -225,10 +259,9 @@
                "else " \
                        "if run loaduimage; then " \
                                "run mmcboot; " \
-                       "else " \
-                               "echo ERR: Fail to boot from MMC; " \
+                       "else run netboot; " \
                        "fi; " \
                "fi; " \
-       "else exit; fi"
+       "else run netboot; fi"
 
 #endif /* __MX23_OLINUXINO_CONFIG_H__ */
-- 
1.8.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to