Thierry,
On Thu, Feb 14, 2013 at 12:54 AM, Thierry Reding
<thierry.red...@avionic-design.de> wrote:
> Move the nand-controller node to the tegra20-tamonten.dtsi so that it
> can be shared between all derived boards.
>
> Signed-off-by: Thierry Reding <thierry.red...@avionic-design.de>
> ---
> This depends on Tom's "Tegra: MMC: Add DT support for MMC to T20 boards"
> patches.
>
> board/avionic-design/dts/tegra20-tamonten.dtsi | 11 +++++++++++
> board/avionic-design/dts/tegra20-tec.dts | 11 -----------
> 2 files changed, 11 insertions(+), 11 deletions(-)
>
> diff --git a/board/avionic-design/dts/tegra20-tamonten.dtsi
> b/board/avionic-design/dts/tegra20-tamonten.dtsi
> index 4766aba..0a95ac1 100644
> --- a/board/avionic-design/dts/tegra20-tamonten.dtsi
> +++ b/board/avionic-design/dts/tegra20-tamonten.dtsi
> @@ -279,6 +279,17 @@
> status = "okay";
> };
>
> + nand-controller@70008000 {
> + nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
> + nvidia,width = <8>;
> + nvidia,timing = <26 100 20 80 20 10 12 10 70>;
> +
> + nand@0 {
> + reg = <0>;
> + compatible = "hynix,hy27uf4g2b", "nand-flash";
> + };
> + };
> +
> i2c@7000c000 {
> clock-frequency = <400000>;
> status = "okay";
> diff --git a/board/avionic-design/dts/tegra20-tec.dts
> b/board/avionic-design/dts/tegra20-tec.dts
> index 376d279..694682c 100644
> --- a/board/avionic-design/dts/tegra20-tec.dts
> +++ b/board/avionic-design/dts/tegra20-tec.dts
> @@ -32,17 +32,6 @@
> clock-frequency = <216000000>;
> };
>
> - nand-controller@70008000 {
> - nvidia,wp-gpios = <&gpio 23 0>; /* PC7 */
> - nvidia,width = <8>;
> - nvidia,timing = <26 100 20 80 20 10 12 10 70>;
> -
> - nand@0 {
> - reg = <0>;
> - compatible = "hynix,hy27uf4g2b", "nand-flash";
> - };
> - };
> -
> i2c@7000c000 {
> status = "disabled";
> };
> --
> 1.8.1.2
>
I kinda lost track of this patchset. I'd like to move it into
u-boot-tegra/next if you think it's ready, but I'm not sure if it
conflicts with/works with Stephen's 4th patch of his v2 series ("ARM:
tegra: enable a common set of disk-related commands").
Let me know how you want me to proceed - I'd like to get a PR off to
Albert for ARM/master this week if possible.
Thanks,
Tom
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
