Hi Jaehoon, Auto-stop command is not related to read/write issue. Today, I commented the 'auto-stop command' enable code and tested, SD/EMMC read write and EMMC boot work fine. Hence enabling Auto-stop command is not required. I shall update the same in next patchset.
Thanks & Regards Amarendra Reddy On 9 April 2013 16:19, Jaehoon Chung <jh80.ch...@samsung.com> wrote: > Hi Amar, > > I'm not sure that need to enable the auto-stop command feature. > why do you enable this feature? Is there any benefit? > Is it related with read/write issue? > > Best Regards, > Jaehoon Chung > > On 04/03/2013 11:08 PM, Amar wrote: > > This patch enumerates dwmci and set auto stop command during > > dwmci initialisation. > > EMMC read/write is not happening in current implementation > > due to improper fifo size computation. Hence modified the fifo size > > computation to resolve EMMC read write issues. > > > > Signed-off-by: Amar <amarendra...@samsung.com> > > --- > > Changes since V1: > > 1)Created the macros RX_WMARK_SHIFT and RX_WMARK_MASK in header > file. > > > > Changes since V2: > > 1)Updation of commit message and resubmition of proper patch set. > > > > Changes since V3: > > 1)Updated to use the macro DWMCI_CTRL_SEND_AS_CCSD instead of > > the hard coded value (1 << 10). > > > > Changes since V4: > > 1)Updated the function dwmci_send_cmd() to use get_timer() instead > > of using mdelay(1). > > > > Changes since V5: > > 1)Updated in response to review comments. > > > > Changes since V6: > > No change. > > > > Changes since V7: > > 1)Updated the function dwmci_setup_bus() to return 0 if (freq == > 0). > > This is to avoid the run time exception "raise:Signal # 8 caught". > > > > drivers/mmc/dw_mmc.c | 28 ++++++++++++++++++---------- > > 1 file changed, 18 insertions(+), 10 deletions(-) > > > > diff --git a/drivers/mmc/dw_mmc.c b/drivers/mmc/dw_mmc.c > > index 4070d4e..963a515 100644 > > --- a/drivers/mmc/dw_mmc.c > > +++ b/drivers/mmc/dw_mmc.c > > @@ -129,13 +129,13 @@ static int dwmci_send_cmd(struct mmc *mmc, struct > mmc_cmd *cmd, > > unsigned int timeout = 100000; > > u32 retry = 10000; > > u32 mask, ctrl; > > + ulong start = get_timer(0); > > > > while (dwmci_readl(host, DWMCI_STATUS) & DWMCI_BUSY) { > > - if (timeout == 0) { > > + if (get_timer(start) > timeout) { > > printf("Timeout on data busy\n"); > > return TIMEOUT; > > } > > - timeout--; > > } > > > > dwmci_writel(host, DWMCI_RINTSTS, DWMCI_INTMSK_ALL); > > @@ -143,7 +143,6 @@ static int dwmci_send_cmd(struct mmc *mmc, struct > mmc_cmd *cmd, > > if (data) > > dwmci_prepare_data(host, data); > > > > - > > dwmci_writel(host, DWMCI_CMDARG, cmd->cmdarg); > > > > if (data) > > @@ -231,9 +230,8 @@ static int dwmci_setup_bus(struct dwmci_host *host, > u32 freq) > > int timeout = 10000; > > unsigned long sclk; > > > > - if (freq == host->clock) > > + if ((freq == host->clock) || (freq == 0)) > > return 0; > > - > > /* > > * If host->mmc_clk didn't define, > > * then assume that host->bus_hz is source clock value. > > @@ -314,7 +312,7 @@ static void dwmci_set_ios(struct mmc *mmc) > > static int dwmci_init(struct mmc *mmc) > > { > > struct dwmci_host *host = (struct dwmci_host *)mmc->priv; > > - u32 fifo_size, fifoth_val; > > + u32 fifo_size, fifoth_val, ier; > > > > dwmci_writel(host, DWMCI_PWREN, 1); > > > > @@ -323,6 +321,14 @@ static int dwmci_init(struct mmc *mmc) > > return -1; > > } > > > > + /* Enumerate at 400KHz */ > > + dwmci_setup_bus(host, mmc->f_min); > > + > > + /* Set auto stop command */ > > + ier = dwmci_readl(host, DWMCI_CTRL); > > + ier |= DWMCI_CTRL_SEND_AS_CCSD; > > + dwmci_writel(host, DWMCI_CTRL, ier); > > + > > dwmci_writel(host, DWMCI_RINTSTS, 0xFFFFFFFF); > > dwmci_writel(host, DWMCI_INTMASK, 0); > > > > @@ -332,11 +338,13 @@ static int dwmci_init(struct mmc *mmc) > > dwmci_writel(host, DWMCI_BMOD, 1); > > > > fifo_size = dwmci_readl(host, DWMCI_FIFOTH); > > - if (host->fifoth_val) > > + fifo_size = ((fifo_size & RX_WMARK_MASK) >> RX_WMARK_SHIFT) + 1; > > + if (host->fifoth_val) { > > fifoth_val = host->fifoth_val; > > - else > > - fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size/2 -1) | > > - TX_WMARK(fifo_size/2); > > + } else { > > + fifoth_val = MSIZE(0x2) | RX_WMARK(fifo_size / 2 - 1) | > > + TX_WMARK(fifo_size / 2); > > + } > > dwmci_writel(host, DWMCI_FIFOTH, fifoth_val); > > > > dwmci_writel(host, DWMCI_CLKENA, 0); > > > > _______________________________________________ > U-Boot mailing list > U-Boot@lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot >
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot