Hello Lubomir, Am 04.06.2013 08:49, schrieb Lubomir Popov: > Hi Heiko, > > On 04/06/13 07:26, Heiko Schocher wrote: >> Hello Lubomir, >> >> Am 03.06.2013 07:13, schrieb Heiko Schocher: >>> Hello Lubomir, >>> >>> Am 02.06.2013 13:42, schrieb Lubomir Popov: >>>>> Hello Lubomir, >>>>> >>>>> Am 01.06.2013 18:44, schrieb Lubomir Popov: >>>>>> New i2c_read, i2c_write and i2c_probe functions, tested on OMAP4 >>>>>> (4430/60/70), OMAP5 (5430) and AM335X (3359); should work on older >>>>>> OMAPs and derivatives as well. The only anticipated exception would >>>>>> be the OMAP2420, which shall require driver modification. >>> [...] >>>>>> drivers/i2c/omap24xx_i2c.c | 490 >>>>>> +++++++++++++++++++++++++++------------------ >>>>>> 1 file changed, 299 insertions(+), 191 deletions(-) >>>>> >>>>> Tested on 3 arm335x based boards, which one uses i2c in SPL >>>>> code for getting ram parameters, so: >>>>> >>>>> Tested-by: Heiko Schocher <h...@denx.de> >>>> Many thanks for testing, to Tom as well (he did it on the >>>> Beagleboards, but for one of the older versions, V3 I believe, >>>> right?). >>>> When it comes to versions, I see that V1 and V2 are still listed >>>> in patchwork, probably because of slightly different wording of >>>> the subject: >>>> http://patchwork.ozlabs.org/patch/233823/ >>>> http://patchwork.ozlabs.org/patch/246204/ >>>> Could you or Tom clean this up, please? Thanks. >>> >>> Cleared the v3 v4 version, but missed the v2 and v1, Done. >> >> just doing a "MAKEALL arm" with your patch applied and get this error: >> >> Configuring for omap2420h4 board... >> omap24xx_i2c.c:497:17: error: 'struct i2c' has no member named >> 'irqstatus_raw' >> omap24xx_i2c.c:528:12: error: 'struct i2c' has no member named >> 'irqstatus_raw' >> arm-linux-gnueabi-size: './u-boot': No such file >> omap24xx_i2c.c: In function 'wait_for_bb': >> omap24xx_i2c.c:497:17: error: 'struct i2c' has no member named >> 'irqstatus_raw' >> omap24xx_i2c.c: In function 'wait_for_event': >> omap24xx_i2c.c:528:12: error: 'struct i2c' has no member named >> 'irqstatus_raw' >> make[1]: *** [omap24xx_i2c.o] Fehler 1 >> make: *** [drivers/i2c/libi2c.o] Fehler 2 >> make: *** Warte auf noch nicht beendete Prozesse... >> >> Please fix this and run a "MAKEALL arm" before repost, thanks! > We have agreed upon this breakage with Tom - the OMAP2420 shall not > be supported anymore in the next release. At least I understood it > that way (and have noted it accordingly in the comments).
Ah, ok ... so affected boards should fixed too ... @Tom: Could you than pick up this patch? > I could of course make a very simple modification that would allow > build without errors, but the driver shall not work on the 2420; in > order to make it work, a more serious rework is required. I don't > have however any 2420 hardware to test upon. > > Tom? bye, Heiko -- DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot