-----Original Message----- From: Wood Scott-B07421 Sent: Friday, June 14, 2013 5:50 AM To: Zhang Ying-B40530 Cc: Wood Scott-B07421; u-boot@lists.denx.de; aflem...@gmail.com; Xie Xiaobo-R63061 Subject: Re: [PATCH] powerpc/p1022ds: nand: introduce the TPL based on the SPL
On 06/13/2013 02:27:44 AM, Zhang Ying-B40530 wrote: > > > -----Original Message----- > From: Wood Scott-B07421 > Sent: Thursday, June 13, 2013 6:29 AM > To: Zhang Ying-B40530 > Cc: u-boot@lists.denx.de; aflem...@gmail.com; Xie Xiaobo-R63061; > Zhang Ying-B40530 > Subject: Re: [PATCH] powerpc/p1022ds: nand: introduce the TPL based > on the SPL > > On 06/09/2013 12:54:43 AM, ying.zh...@freescale.com wrote: > > From: Ying Zhang <b40...@freescale.com> > > > > Due to the nand SPL on the board P1022DS has a size limit, it can > not > > be > > more than 4K. So, the SPL cannot initialize the DDR with the SPD > code. > > This patch introduces TPL to enable a loader stub that runs in the > L2 > > SRAM, > > after being loaded by the code from the SPL. It initializes the DDR > > with > > the SPD. > > > > The TPL's size is sizeable, the maximum size must not exceed the > size > > of L2 > > SRAM. It initializes the DDR through SPD code, and copys final uboot > > image > > to DDR. So there are three stage uboot images: > > * spl_boot, 4KB size, pad to 128K byte. > > * tpl_boot, 88K size, pad to 128K size. The env variables are > > copied to L2 SRAM, so that ddr SPD code can get the interleaving > > mode setting in env. It loads final uboot image from offset > > 256KB. > > * final uboot image, size is variable depends on the functions > > enabled. > > > > This patch is on top of the patch: > > powerpc/p1022ds: boot from SD Card with SPL > > > > Signed-off-by: Ying Zhang <b40...@freescale.com> > > --- > > Makefile | 25 +++- > > README | 55 ++++++- > > arch/powerpc/config.mk | 2 + > > arch/powerpc/cpu/mpc85xx/spl_minimal.c | 16 ++ > > arch/powerpc/cpu/mpc85xx/u-boot-tpl.lds | 80 +++++++++ > > .../cpu/mpc8xxx/ddr/lc_common_dimm_params.c | 4 +- > > arch/powerpc/lib/Makefile | 2 + > > board/freescale/p1022ds/Makefile | 3 + > > board/freescale/p1022ds/spl_minimal.c | 56 +------ > > board/freescale/p1022ds/tlb.c | 4 +- > > board/freescale/p1022ds/tpl.c | 101 > > ++++++++++++ > > common/Makefile | 9 + > > common/cmd_nvedit.c | 8 +- > > config.mk | 32 ++++ > > doc/README.TPL | 93 > +++++++++++ > > drivers/mtd/nand/Makefile | 8 + > > drivers/mtd/nand/fsl_elbc_tpl.c | 168 > > ++++++++++++++++++++ > > drivers/serial/serial.c | 2 +- > > include/bootstage.h | 3 +- > > include/configs/P1022DS.h | 75 +++++++-- > > tpl/Makefile | 161 > > +++++++++++++++++++ > > 21 files changed, 824 insertions(+), 83 deletions(-) > > create mode 100644 arch/powerpc/cpu/mpc85xx/u-boot-tpl.lds > > create mode 100644 board/freescale/p1022ds/tpl.c > > create mode 100644 doc/README.TPL > > create mode 100644 drivers/mtd/nand/fsl_elbc_tpl.c > > create mode 100644 tpl/Makefile > > > > diff --git a/README b/README > > index 7add6d4..04f9aa5 100644 > > --- a/README > > +++ b/README > > @@ -2985,9 +2985,10 @@ FIT uImage format: > > Set for the SPL on PPC mpc8xxx targets, support for > > arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in SPL binary. > > > > - CONFIG_SPL_COMMON_INIT_DDR > > + CONFIG_COMMON_INIT_DDR > > Set for common ddr init with serial presence detect in > > - SPL binary. > > + SPL binary or TPL binary. > > + > > CONFIG_SYS_NAND_5_ADDR_CYCLE, > > CONFIG_SYS_NAND_PAGE_COUNT, > > CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE, > > CONFIG_SYS_NAND_BLOCK_SIZE, > > CONFIG_SYS_NAND_BAD_BLOCK_POS, > > @@ -3058,6 +3059,56 @@ FIT uImage format: > > option to re-enable it. This will affect the output of > > the > > bootm command when booting a FIT image. > > > > +- TPL framework > > + CONFIG_TPL > > + Enable building of TPL globally. > > + > > + CONFIG_TPL_LDSCRIPT > > + LDSCRIPT for linking the TPL binary. > > + > > + CONFIG_TPL_MAX_SIZE > > + Maximum size of the TPL image (text, data, rodata, and > > + linker lists sections), BSS excluded. > > + When defined, the linker checks that the actual size > > does > > + not exceed it. > > + > > + CONFIG_SPL_TEXT_BASE > > + TEXT_BASE for linking the TPL binary. > > + > > + CONFIG_TPL_LIBCOMMON_SUPPORT > > + Support for common/libcommon.o in TPL binary > > + > > + CONFIG_TPL_LIBDISK_SUPPORT > > + Support for disk/libdisk.o in TPL binary > > + > > + CONFIG_TPL_I2C_SUPPORT > > + Support for drivers/i2c/libi2c.o in TPL binary > > + > > + CONFIG_TPL_MPC8XXX_INIT_DDR_SUPPORT > > + Set for the TPL on PPC mpc8xxx targets, support for > > + arch/powerpc/cpu/mpc8xxx/ddr/libddr.o in TPL binary. > > + > > + CONFIG_TPL_SERIAL_SUPPORT > > + Support for drivers/serial/libserial.o in TPL binary > > + > > + CONFIG_TPL_LIBGENERIC_SUPPORT > > + Support for lib/libgeneric.o in TPL binary > > + > > + CONFIG_TPL_ENV_SUPPORT > > + Support for the environment operating in TPL binary > > + > > + CONFIG_TPL_PAD_TO > > + Image offset to which the TPL should be padded before > > appending > > + the TPL payload. By default, this is defined as > > + CONFIG_TPL_MAX_SIZE, or 0 if CONFIG_TPL_MAX_SIZE is > > undefined. > > + CONFIG_TPL_PAD_TO must be either 0, meaning to append > > the TPL > > + payload without any padding, or >= CONFIG_TPL_MAX_SIZE. > > + > > + CONFIG_TPL_TARGET > > + Final target image containing SPL and payload. Some > > TPLs > > + use an arch-specific makefile fragment instead, for > > + example if more than one image needs to be produced. > > Let's please not just duplicate all the SPL stuff with s/SPL/TPL/. > Now > that the concept of a separate autoconf.mk is apparently less > controversial than when I suggested it a while back, let's generalize > it into multiple U-Boot phases, each of which has its own autoconf.mk. > The same set of symbols would be used to build any phase (ideally > including the main phase) -- the symbols would just be declared under > different ifdefs. > [Zhang Ying] > I know the concept of a separate autoconf.mk for multiple U-Boot > phases. > If these symbols are only used in the C files, should do as you say. > But most of these symbols were used in the Makefile to contain the > Library. The patch "separate autoconf.mk" has not be merged, in this > case, they can only declared separately. Treat the autoconf.mk patch as a dependency. Don't try to hack around its absence. [Zhang Ying] According to what you said, the same set of symbols will be declared under different ifdefs. That's the trouble, "The same set of symbols declared under different ifdefs" will not be effective in the "Makefile", in the current case. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
