Before parsing LAW table i.e. init_law, boot loader should disable all
previous LAWs except DDR LAWs which has been created by previous
pre boot loader during DDR initialization.

Signed-off-by: Prabhakar Kushwaha <prabha...@freescale.com>
---
 arch/powerpc/cpu/mpc8xxx/law.c |   43 +++++++++++++++++++++++++++++++---------
 1 file changed, 34 insertions(+), 9 deletions(-)

diff --git a/arch/powerpc/cpu/mpc8xxx/law.c b/arch/powerpc/cpu/mpc8xxx/law.c
index a401083..0aa6ce1 100644
--- a/arch/powerpc/cpu/mpc8xxx/law.c
+++ b/arch/powerpc/cpu/mpc8xxx/law.c
@@ -221,6 +221,32 @@ int set_ddr_laws(u64 start, u64 sz, enum law_trgt_if id)
 }
 #endif /* not SPL */
 
+void disable_non_ddr_laws(void)
+{
+       int i;
+       int id;
+       for (i = 0; i < FSL_HW_NUM_LAWS; i++) {
+               u32 lawar = in_be32(LAWAR_ADDR(i));
+
+               if (lawar & LAW_EN) {
+                       id = (lawar & ~LAW_EN) >> 20;
+                       switch (id) {
+                       case LAW_TRGT_IF_DDR_1:
+                       case LAW_TRGT_IF_DDR_2:
+                       case LAW_TRGT_IF_DDR_3:
+                       case LAW_TRGT_IF_DDR_4:
+                       case LAW_TRGT_IF_DDR_INTRLV:
+                       case LAW_TRGT_IF_DDR_INTLV_34:
+                       case LAW_TRGT_IF_DDR_INTLV_123:
+                       case LAW_TRGT_IF_DDR_INTLV_1234:
+                                               continue;
+                       default:
+                                               disable_law(i);
+                       }
+               }
+       }
+}
+
 void init_laws(void)
 {
        int i;
@@ -233,6 +259,14 @@ void init_laws(void)
 #error FSL_HW_NUM_LAWS can not be greater than 32 w/o code changes
 #endif
 
+#if !defined(CONFIG_SECURE_BOOT)
+       /*
+        * if any non DDR LAWs has been created earlier, remove them before
+        * LAW table is parsed.
+       */
+       disable_non_ddr_laws();
+#endif
+
        /*
         * Any LAWs that were set up before we booted assume they are meant to
         * be around and mark them used.
@@ -244,15 +278,6 @@ void init_laws(void)
                        gd->arch.used_laws |= (1 << i);
        }
 
-#if (defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)) || \
-       (defined(CONFIG_SPL) && !defined(CONFIG_SPL_BUILD))
-       /*
-        * in SPL boot we've already parsed the law_table and setup those LAWs
-        * so don't do it again.
-        */
-       return;
-#endif
-
        for (i = 0; i < num_law_entries; i++) {
                if (law_table[i].index == -1)
                        set_next_law(law_table[i].addr, law_table[i].size,
-- 
1.7.9.5



_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to