Hello Heiko,
--On May 06, 2014 16:46 +0200 Heiko Schocher <h...@denx.de> wrote:
Hello Christian,
Am 06.05.2014 13:30, schrieb Christian Riesch:
Tom,
Thank you very much for your investigations :-)
--On April 26, 2014 13:34 -0400 Tom Taylor <ttaylor.ta...@gmail.com>
wrote:
I'm a U-Boot newbie so please feel free to correct how I'm reporting
this issue..
I recently downloaded the 2014.04-rc3 snapshot to build U-Boot for my
custom DA850-based board. The only change was to add a new target
"dav850evm_nand" in boards.cfg with the added parameter "USE_NAND".
The resulting AIS file was programmed into EVM-compatible NAND using
standard sfh_OMAP-L138 method.
The board failed to boot, and stayed in a loop printing the SPL console
message repeatedly.
After some debugging with CCS 5.5 and an XDS100v2, I found that
incorrect code was being loaded into the 0xc108000 RAM destination. The
da850evm.h file defines CONFIG_SYS_NAND_U_BOOT_OFFS as 0x28000, which
corresponds to an AIS offset of 0x8000 but the u-boot header did not
appear there in the AIS file. A search revealed that the Makefile
catenated u-boot immediately after the SPL without any padding.
Further investigation revealed that the target Makefile needs
CONFIG_SPL_MAX_SIZE to be defined as 0x8000 in order for the padding to
be performed properly; however, this constant was apparently deleted
during a series of changes in April, 2013 to accommodate separate code
and BSS size limits for another target. In its place,
CONFIG_SPL_MAX_FOOTPRINT was defined as 32768. Unfortunately, the
da850evm Makefile does not refer to this constant.
To solve the problem, I added the following 2 lines in my
custom-modified da850evm.h:
# define CONFIG_SPL_PAD_TO 0x8000
# define CONFIG_SPL_MAX_SIZE 0x8000
although the first line may not be strictly required.
Yes, CONFIG_SPL_PAD_TO is currently not used for the 'make u-boot.ais'
target in the Makefile. Instead, the Makefile uses CONFIG_SPL_MAX_SIZE
for padding the SPL, which is probably wrong.
Yes, CONFIG_SPL_PAD_TO is the correct define. On the other hand
the question is is CONFIG_SPL_PAD_TO not always equal to
CONFIG_SPL_MAX_SIZE ?
I guess yes.
This solved the
problem and allowed the board to boot.
Doesn't this mean that other similar targets may be broken?
I think yes.
I think the right fix would be to change the Makefile to use
CONFIG_SPL_PAD_TO instead of CONFIG_SPL_MAX_SIZE for the u-boot.ais
target.
diff --git a/Makefile b/Makefile
index ff38a43..869f442 100644
--- a/Makefile
+++ b/Makefile
@@ -890,7 +890,7 @@ MKIMAGEFLAGS_u-boot-spl.ais = -s -n $(if
$(CONFIG_AIS_CONFIG_FILE), \ spl/u-boot-spl.ais: spl/u-boot-spl.bin FORCE
$(call if_changed,mkimage)
-OBJCOPYFLAGS_u-boot.ais = -I binary -O binary
--pad-to=$(CONFIG_SPL_MAX_SIZE) +OBJCOPYFLAGS_u-boot.ais = -I binary -O
binary --pad-to=$(CONFIG_SPL_PAD_TO) u-boot.ais: spl/u-boot-spl.ais
u-boot.img FORCE
$(call if_changed,pad_cat)
And then check all ARM926EJS/Davinci configurations that use SPL:
(extending Tom Rini's grep command from his email)
$ git grep -l ARM926EJS include/configs/ | xargs grep -l DAVINCI | xargs
grep -l _SPL_ include/configs/cam_enc_4xx.h
include/configs/da830evm.h
include/configs/da850evm.h
include/configs/hawkboard.h
include/configs/ipam390.h
For the cam_enc_4xx CONFIG_SPL_PAD_TO is already defined, so it should
work fine after fixing the Makefile. Heiko, any comments on this? Are
you actually using the u-boot.ais target?
I have no board to test, but I think it is used.
da830evm and hawkboard did not use CONFIG_SPL_MAX_SIZE, so no need to
fix them.
da850evm: We should add CONFIG_SPL_PAD_TO as already suggested by you.
ipam390.h: I think the #define CONFIG_SPL_MAX_SIZE 0x20000 should be
removed or replaced by #define CONFIG_SPL_PAD_TO 0x20000. But actually
the board has been added after the commits that replace grep -lr
CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT, so why didn't that
issue come up when adding the board to mainline? Heiko, any comments?
Are you using make u-boot.ais here or something else?
I am not sure, if we can just remove CONFIG_SPL_MAX_SIZE for this
board, as it maybe has only 0x20000 space for the SPL ?
I had another look at ipam390.h, currently there is
#define CONFIG_SPL_MAX_SIZE 0x20000
#define CONFIG_SPL_MAX_FOOTPRINT 32768
So according to README, the linker checks if the SPL including BSS is
smaller than 32kB, and if the SPL excluding BSS is smaller than 128 kB. So
the check against CONFIG_SPL_MAX_SIZE is always fulfilled. Therefore it is
save to replace CONFIG_SPL_MAX_SIZE with CONFIG_SPL_PAD_TO.
maybe:
# if !defined(CONFIG_SPL_PAD_TO)
define CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE
# endif
is better? Heh, thats the case, see:
./include/config_fallbacks.h
so, your Makefile patch should be Ok ...
Ok, so no change is required for ipam390.
I'll send a patch.
Christian
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
