Added in v1: - Add pin mux support for ls1021aqds. Test log:
U-Boot 2014.07-01993-g052b512-dirty (Oct 20 2014 - 19:58:20) CPU: Freescale LayerScape LS1020E, Version: 1.0, (0x87081010) Clock Configuration: CPU0(ARMV7):1000 MHz, Bus:300 MHz, DDR:800 MHz (1600 MT/s data rate), Reset Configuration Word (RCW): 00000000: 0608000a 00000000 00000000 00000000 00000010: 60000000 00407900 e0025a00 21046000 00000020: 00000000 00000000 00000000 00038000 00000030: 00000000 001b7200 00000000 00000000 Board: LS1021AQDS vBank: 4 Sys ID:0x2b, Sys Ver: 0x11 FPGA: v13 (QIXIS_LS1021QDS_2014_08_27_1658), build 65386 I2C: ready DRAM: Initializing DDR....using SPD Detected UDIMM 18KSF51272AZ-1G6K1 2 GiB (DDR3, 32-bit, CL=11, ECC off) Using SERDES1 Protocol: 96 (0x60) Flash: 128 MiB NAND: 0 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: eTSEC1 is in sgmii mode eTSEC2 is in sgmii mode Phy not found PHY reset timed out Phy not found PHY reset timed out eTSEC1, eTSEC2, eTSEC3 [PRIME] => pri baudrate=115200 boot=dhcp 82000000 r66431/ls1/uImage.ls1021a; tftp 8f000000 r66431/ls1/ls1021a-qds.dtb; tftp 88000000 r66431/ls1/fsl-image-x11-ls1021aqds-20140424073555.rootfs.ext2.gz.u-boot ; bootm 82000000 88000000 8f000000 boot_bank0=i2c mw 0x66 0x50 0x40;i2c mw 0x66 0x10 0x20;i2c mw 0x66 0x10 0x21 boot_bank4=i2c mw 0x66 0x50 0x44;i2c mw 0x66 0x10 0x20;i2c mw 0x66 0x10 0x21 bootargs=root=/dev/ram0 rw console=ttyS0,115200 bootdelay=3 eth1addr=00:04:9f:03:2e:c5 eth2addr=00:04:9f:03:2e:c6 eth3addr=00:04:9f:03:2e:c7 eth4addr=00:04:9f:03:2e:c8 eth5addr=00:04:9f:03:2e:c9 eth6addr=00:04:9f:03:2e:ca ethact=eTSEC3 ethaddr=00:04:9f:03:2e:c4 ethprime=eTSEC3 fdt_high=0xffffffff hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=null,ecc=off initrd_high=0xffffffff ipaddr=192.168.1.121 loadaddr=0x82000000 scsidevs=0 serverip=192.168.1.1 stderr=serial stdin=serial stdout=serial zhuoboot=tftp 82000000 b46552/ls1021aqds/uImage.ls1021a; tftp 8f000000 b46552/ls1021aqds/ls1021a-qds.dtb;tftp 88000000 b46552/ls1021aqds/ramdisk.small;bootm 82000000 88000000 8f000000 Environment size: 1117/8188 bytes => i2c md 0x66 0x5e 005e: 00 00 12 81 f7 ff ff ff ff ef e7 00 3f ff ff ff ............?... => set hwconfig "fsl_ddr:ctlr_intlv=null,bank_intlv=null,ecc=off;sai" => save Saving Environment to Flash... Un-Protected 1 sectors Erasing Flash... . done Erased 1 sectors Writing to Flash... 9....8....7....6....5....4....3....2....1....9....8....7....6....5....4....3....2....1....done Protected 1 sectors => run boot_bank4 U-Boot 2014.07-01993-g052b512-dirty (Oct 20 2014 - 19:58:20) CPU: Freescale LayerScape LS1020E, Version: 1.0, (0x87081010) Clock Configuration: CPU0(ARMV7):1000 MHz, Bus:300 MHz, DDR:800 MHz (1600 MT/s data rate), Reset Configuration Word (RCW): 00000000: 0608000a 00000000 00000000 00000000 00000010: 60000000 00407900 e0025a00 21046000 00000020: 00000000 00000000 00000000 00038000 00000030: 00000000 001b7200 00000000 00000000 Board: LS1021AQDS vBank: 4 Sys ID:0x2b, Sys Ver: 0x11 FPGA: v13 (QIXIS_LS1021QDS_2014_08_27_1658), build 65386 I2C: ready DRAM: Initializing DDR....using SPD Detected UDIMM 18KSF51272AZ-1G6K1 2 GiB (DDR3, 32-bit, CL=11, ECC off) Using SERDES1 Protocol: 96 (0x60) Flash: 128 MiB NAND: 0 MiB MMC: FSL_SDHC: 0 In: serial Out: serial Err: serial Net: eTSEC1 is in sgmii mode eTSEC2 is in sgmii mode Phy not found PHY reset timed out Phy not found PHY reset timed out eTSEC1, eTSEC2, eTSEC3 [PRIME] => i2c md 0x66 0x5e 005e: 0c 00 12 81 f7 ff ff ff ff ef e7 00 3f ff ff ff ............?... => [b46683@rhuath ~]$ _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot