Hi Hyungwon, > This patch adds support for Odroid-XU3. > > Change-Id: Ia45d119a62b126f2328684485b8c372ba6acbe00
As stated previously - please run checkpatch.pl on a patch before submitting. > Signed-off-by: Hyungwon Hwang <human.hw...@samsung.com> > --- > arch/arm/cpu/armv7/exynos/Kconfig | 4 + > arch/arm/dts/Makefile | 3 +- > arch/arm/dts/exynos5422-odroidxu3.dts | 72 ++++++++++ > board/samsung/odroid-xu3/Kconfig | 12 ++ > board/samsung/odroid-xu3/MAINTAINERS | 6 + > board/samsung/odroid-xu3/Makefile | 7 + > board/samsung/odroid-xu3/odroid-xu3.c | 132 ++++++++++++++++++ > board/samsung/odroid-xu3/setup.h | 123 +++++++++++++++++ > configs/odroid-xu3_defconfig | 4 + > include/configs/odroid_xu3.h | 243 > ++++++++++++++++++++++++++++++++++ 10 files changed, 605 > insertions(+), 1 deletion(-) create mode 100644 > arch/arm/dts/exynos5422-odroidxu3.dts create mode 100644 > board/samsung/odroid-xu3/Kconfig create mode 100644 > board/samsung/odroid-xu3/MAINTAINERS create mode 100644 > board/samsung/odroid-xu3/Makefile create mode 100644 > board/samsung/odroid-xu3/odroid-xu3.c create mode 100644 > board/samsung/odroid-xu3/setup.h create mode 100644 > configs/odroid-xu3_defconfig create mode 100644 > include/configs/odroid_xu3.h > > diff --git a/arch/arm/cpu/armv7/exynos/Kconfig > b/arch/arm/cpu/armv7/exynos/Kconfig index 3a25fee..a47cb34 100644 > --- a/arch/arm/cpu/armv7/exynos/Kconfig > +++ b/arch/arm/cpu/armv7/exynos/Kconfig > @@ -22,6 +22,9 @@ config TARGET_TRATS2 > config TARGET_ODROID > bool "Exynos4412 Odroid board" > > +config TARGET_ODROID_XU3 > + bool "Exynos5422 Odroid board" > + > config TARGET_ARNDALE > bool "Exynos5250 Arndale board" > select OF_CONTROL if !SPL_BUILD > @@ -60,6 +63,7 @@ source "board/samsung/universal_c210/Kconfig" > source "board/samsung/origen/Kconfig" > source "board/samsung/trats2/Kconfig" > source "board/samsung/odroid/Kconfig" > +source "board/samsung/odroid-xu3/Kconfig" > source "board/samsung/arndale/Kconfig" > source "board/samsung/smdk5250/Kconfig" > source "board/samsung/smdk5420/Kconfig" > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 2dcfcc0..66191f9 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -12,7 +12,8 @@ dtb-$(CONFIG_EXYNOS5) += exynos5250-arndale.dtb \ > exynos5250-smdk5250.dtb \ > exynos5420-smdk5420.dtb \ > exynos5420-peach-pit.dtb \ > - exynos5800-peach-pi.dtb > + exynos5800-peach-pi.dtb \ > + exynos5422-odroidxu3.dtb > dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \ > tegra20-medcom-wide.dtb \ > tegra20-paz00.dtb \ > diff --git a/arch/arm/dts/exynos5422-odroidxu3.dts > b/arch/arm/dts/exynos5422-odroidxu3.dts new file mode 100644 > index 0000000..34f52c6 > --- /dev/null > +++ b/arch/arm/dts/exynos5422-odroidxu3.dts > @@ -0,0 +1,72 @@ > +/* > + * Odroid XU3 device tree source > + * > + * Copyright (c) 2014 Samsung Electronics Co., Ltd. > + * http://www.samsung.com > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +/dts-v1/; > +/include/ "exynos54xx.dtsi" > + > +/ { > + model = "Odroid XU3 based on EXYNOS5422"; > + compatible = "samsung,odroidxu3", "samsung,exynos5"; > + > + config { > + hwid = "smdk5420 TEST A-A 9382"; > + }; > + > + aliases { > + serial0 = "/serial@12C00000"; > + console = "/serial@12C20000"; > + }; > + > + memory { > + device_type = "memory"; > + reg = <0x40000000 0x10000000 > + 0x50000000 0x10000000 > + 0x60000000 0x10000000 > + 0x70000000 0x10000000 > + 0x80000000 0x10000000 > + 0x90000000 0x10000000 > + 0xa0000000 0x10000000 > + 0xb0000000 0xea00000>; > + }; > + > + serial@12C20000 { > + status="okay"; > + }; > + > + /* s2mps11 is on i2c bus 4 */ > + i2c@12ca0000 { > + #address-cells = <1>; > + #size-cells = <0>; > + pmic@66 { > + reg = <0x66>; > + compatible = "samsung,s2mps11-pmic"; > + }; > + }; > + > + mmc@12200000 { > + samsung,bus-width = <8>; > + samsung,timing = <1 3 3>; > + samsung,removable = <0>; > + samsung,pre-init; > + }; > + > + mmc@12210000 { > + status = "disabled"; > + }; > + > + mmc@12220000 { > + samsung,bus-width = <4>; > + samsung,timing = <1 2 3>; > + samsung,removable = <1>; > + }; > + > + mmc@12230000 { > + status = "disabled"; > + }; > +}; > diff --git a/board/samsung/odroid-xu3/Kconfig > b/board/samsung/odroid-xu3/Kconfig new file mode 100644 > index 0000000..6159692 > --- /dev/null > +++ b/board/samsung/odroid-xu3/Kconfig > @@ -0,0 +1,12 @@ > +if TARGET_ODROID_XU3 > + > +config SYS_BOARD > + default "odroid-xu3" > + > +config SYS_VENDOR > + default "samsung" > + > +config SYS_CONFIG_NAME > + default "odroid_xu3" > + > +endif > diff --git a/board/samsung/odroid-xu3/MAINTAINERS > b/board/samsung/odroid-xu3/MAINTAINERS new file mode 100644 > index 0000000..50cf928 > --- /dev/null > +++ b/board/samsung/odroid-xu3/MAINTAINERS > @@ -0,0 +1,6 @@ > +ODROID-XU3 BOARD > +M: Hyungwon Hwang <human.hw...@samsung.com> > +S: Maintained > +F: board/samsung/odroid-xu3/ > +F: include/configs/odroid_xu3.h > +F: configs/odroid-xu3_defconfig > diff --git a/board/samsung/odroid-xu3/Makefile > b/board/samsung/odroid-xu3/Makefile new file mode 100644 > index 0000000..85ae5c5 > --- /dev/null > +++ b/board/samsung/odroid-xu3/Makefile > @@ -0,0 +1,7 @@ > +# > +# Copyright (c) 2014 Samsung Electronics Co., Ltd. All rights > reserved. +# > +# SPDX-License-Identifier: GPL-2.0+ > +# > + > +obj-y := odroid-xu3.o > diff --git a/board/samsung/odroid-xu3/odroid-xu3.c > b/board/samsung/odroid-xu3/odroid-xu3.c new file mode 100644 > index 0000000..f054e4e > --- /dev/null > +++ b/board/samsung/odroid-xu3/odroid-xu3.c > @@ -0,0 +1,132 @@ > +/* > + * Copyright (C) 2014 Samsung Electronics > + * Hyungwon Hwang <human.hw...@samsung.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include <common.h> > +#include <asm/io.h> > +#include <netdev.h> > +#include <asm/arch/cpu.h> > +#include <asm/arch/clock.h> > +#include <asm/arch/power.h> > +#include <asm/arch/gpio.h> > +#include <asm/arch/mmc.h> > +#include <asm/arch/pinmux.h> > +#include <asm/arch/sromc.h> > + > +#include "setup.h" > + > +DECLARE_GLOBAL_DATA_PTR; > + > +unsigned int get_board_rev(void) > +{ > + unsigned int rev = 0; > + return rev; > +} > + > +int exynos_init(void) > +{ > + return 0; > +} > + > +static int board_clock_init(void) > +{ > + unsigned int set, clr, clr_src_cpu, clr_pll_con0; > + struct exynos5420_clock *clk = (struct exynos5420_clock *) > + > samsung_get_base_clock(); > + /* > + * CMU_CPU clocks src to MPLL > + * Bit values: 0 ; 1 > + * MUX_APLL_SEL: FIN_PLL ; FOUT_APLL > + * MUX_CORE_SEL: MOUT_APLL ; SCLK_MPLL > + * MUX_HPM_SEL: MOUT_APLL ; SCLK_MPLL_USER_C > + * MUX_MPLL_USER_SEL_C: FIN_PLL ; SCLK_MPLL > + */ > + > + /* Set CMU_CPU clocks src to OSCCLK */ > + clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1); > + set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1); > + > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); > + > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu))) > + continue; > + > + /* Set APLL to 1200MHz */ > + clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1) | > + PLL_ENABLE(1); > + set = SDIV(0) | PDIV(2) | MDIV(100) | PLL_ENABLE(1); > + > + clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set); > + > + while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT)) > + continue; > + > + /* Set CMU_CPU clocks src to APLL */ > + set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0); > + clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set); > + > + while (MUX_STAT_CPU_CHANGING(readl(&clk->mux_stat_cpu))) > + continue; > + > + clr = ARM_RATIO(7) | CPUD_RATIO(7) | ATB_RATIO(7) | > + PCLK_DBG_RATIO(7) | APLL_RATIO(7) | ARM2_RATIO(7); > + set = ARM_RATIO(0) | CPUD_RATIO(2) | ATB_RATIO(5) | > + PCLK_DBG_RATIO(5) | APLL_RATIO(0) | ARM2_RATIO(0); > + > + clrsetbits_le32(&clk->div_cpu0, clr, set); > + > + while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING) > + continue; > + > + /* Set MPLL to 800MHz */ > + set = SDIV(1) | PDIV(3) | MDIV(200) | PLL_ENABLE(1); > + > + clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set); > + > + while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT)) > + continue; > + > + /* Set CLKMUX_UART src to MPLL */ > + clr = UART0_SEL(7) | UART1_SEL(7) | UART2_SEL(7) | > UART3_SEL(7); > + set = UART0_SEL(3) | UART1_SEL(3) | UART2_SEL(3) | > UART3_SEL(3); + > + clrsetbits_le32(&clk->src_peric0, clr, set); > + > + /* Set SCLK_UART to 400 MHz (MPLL / 2) */ > + clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) | > + UART3_RATIO(15); > + set = UART0_RATIO(1) | UART1_RATIO(1) | UART2_RATIO(1) | > + UART3_RATIO(1); > + > + clrsetbits_le32(&clk->div_peric0, clr, set); > + > + while (readl(&clk->div_stat_peric0) & > DIV_STAT_PERIC0_CHANGING) > + continue; > + > + /* Set CLKMUX_MMC src to MPLL */ > + clr = MUX_MMC0_SEL(7) | MUX_MMC1_SEL(7) | MUX_MMC2_SEL(7); > + set = MUX_MMC0_SEL(3) | MUX_MMC1_SEL(3) | MUX_MMC2_SEL(3); > + > + clrsetbits_le32(&clk->src_fsys, clr, set); > + > + clr = MMC0_RATIO(0x3ff) | MMC1_RATIO(0x3ff) | > MMC2_RATIO(0x3ff); > + set = MMC0_RATIO(0) | MMC1_RATIO(0) | MMC2_RATIO(0); > + > + clrsetbits_le32(&clk->div_fsys1, clr, set); > + > + /* Wait for divider ready status */ > + while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING) > + continue; > + > + return 0; > +} > + > +#ifdef CONFIG_BOARD_EARLY_INIT_F > +int exynos_early_init_f(void) > +{ > + return board_clock_init(); > +} > +#endif > diff --git a/board/samsung/odroid-xu3/setup.h > b/board/samsung/odroid-xu3/setup.h new file mode 100644 > index 0000000..481adb9 > --- /dev/null > +++ b/board/samsung/odroid-xu3/setup.h > @@ -0,0 +1,123 @@ > +/* > + * (C) Copyright 2010 Samsung Electronics > + * Minkyu Kang <mk7.k...@samsung.com> Are those credentials correct? > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __ODROID_XU3_SETUP__ > +#define __ODROID_XU3_SETUP__ > + > +#define SDIV(x) ((x) & 0x7) > +#define PDIV(x) ((x & 0x3f) << 8) > +#define MDIV(x) ((x & 0x3ff) << 16) > +#define FSEL(x) ((x & 0x1) << 27) > +#define PLL_LOCKED_BIT (0x1 << 29) > +#define PLL_ENABLE(x) ((x & 0x1) << 31) Above definitions are already defined in the ./board/samsung/odroid/setup.h It would be a very good idea to extract common setup code and put it in a separate file. Maybe in ./samsung/common directory? > + > +#define DIV_STAT_CHANGING 0x1 > + > +/* CLK_SRC_CPU */ > +#define MUX_APLL_SEL(x) ((x) & 0x1) > +#define MUX_CORE_SEL(x) (((x) & 0x1) << 16) > + > +/* CLK_MUX_STAT_CPU */ > +#define APLL_SEL(x) ((x) & 0x7) > +#define CORE_SEL(x) (((x) & 0x7) << 16) > +#define MUX_STAT_CPU_CHANGING(x) !(((x) & APLL_SEL(0)) > || \ > + (x) & APLL_SEL(1) > || \ > + (x) & CORE_SEL(0) > || \ > + (x) & CORE_SEL(1)) > + > +/* CLK_DIV_CPU0 */ > +#define ARM_RATIO(x) ((x) & 0x7) > +#define CPUD_RATIO(x) (((x) & 0x7) << 4) > +#define ATB_RATIO(x) (((x) & 0x7) << 16) > +#define PCLK_DBG_RATIO(x) (((x) & 0x7) << 20) > +#define APLL_RATIO(x) (((x) & 0x7) << 24) > +#define ARM2_RATIO(x) (((x) & 0x7) << 28) > + > +/* CLK_DIV_STAT_CPU0 */ > +#define DIV_CPUD(x) (((x) & 0x1) << 4) > +#define DIV_ATB(x) (((x) & 0x1) << 16) > +#define DIV_PCLK_DBG(x) (((x) & 0x1) << 20) > +#define DIV_APLL(x) (((x) & 0x1) << 24) > +#define DIV_ARM2(x) (((x) & 0x1) << 28) > + > +#define DIV_STAT_CPU0_CHANGING (DIV_CPUD(DIV_STAT_CHANGING) | \ > + DIV_ATB(DIV_STAT_CHANGING) | \ > + DIV_PCLK_DBG(DIV_STAT_CHANGING) | \ > + DIV_APLL(DIV_STAT_CHANGING) | \ > + DIV_ARM2(DIV_STAT_CHANGING)) > + > +/* Set CLK_SRC_PERIC0 */ > +#define UART0_SEL(x) (((x) & 0xf) << 4) > +#define UART1_SEL(x) (((x) & 0xf) << 8) > +#define UART2_SEL(x) (((x) & 0xf) << 12) > +#define UART3_SEL(x) (((x) & 0xf) << 16) > + > +/* Set CLK_DIV_PERIL0 */ > +#define UART0_RATIO(x) (((x) & 0xf) << 8) > +#define UART1_RATIO(x) (((x) & 0xf) << 12) > +#define UART2_RATIO(x) (((x) & 0xf) << 16) > +#define UART3_RATIO(x) (((x) & 0xf) << 20) > + > +/* Set CLK_DIV_STAT_PERIL0 */ > +#define DIV_UART0(x) ((x) & 0x1) > +#define DIV_UART1(x) (((x) & 0x1) << 4) > +#define DIV_UART2(x) (((x) & 0x1) << 8) > +#define DIV_UART3(x) (((x) & 0x1) << 12) > +#define DIV_UART4(x) (((x) & 0x1) << 16) > + > +#define DIV_STAT_PERIC0_CHANGING (DIV_UART4(DIV_STAT_CHANGING) | \ > + DIV_UART3(DIV_STAT_CHANGING) | \ > + DIV_UART2(DIV_STAT_CHANGING) | \ > + DIV_UART1(DIV_STAT_CHANGING) | \ > + DIV_UART0(DIV_STAT_CHANGING)) > + > +/* CLK_SRC_FSYS */ > +#define MUX_MMC0_SEL(x) (((x) & 0x7) << 8) > +#define MUX_MMC1_SEL(x) (((x) & 0x7) << 12) > +#define MUX_MMC2_SEL(x) (((x) & 0x7) << 16) > + > +/* CLK_DIV_FSYS1 */ > +#define MMC0_RATIO(x) ((x) & 0x3ff) > +#define MMC1_RATIO(x) (((x) & 0x3ff) << 10) > +#define MMC2_RATIO(x) (((x) & 0x3ff) << 20) > + > +#define DIV_MMC0(x) (((x) & 1) << 20) > +#define DIV_MMC1(x) (((x) & 1) << 24) > +#define DIV_MMC2(x) (((x) & 1) << 28) > + > +#define DIV_STAT_FSYS1_CHANGING (DIV_MMC0(DIV_STAT_CHANGING) > | \ > + DIV_MMC1(DIV_STAT_CHANGING) | \ > + DIV_MMC2(DIV_STAT_CHANGING)) > + > +#define MPLL_FOUT_SEL_SHIFT 4 > +#define EXYNOS5_EPLLCON0_LOCKED_SHIFT 29 /* EPLL Locked bit > position*/ +#define TIMEOUT_EPLL_LOCK 1000 > + > +#define AUDIO_0_RATIO_MASK 0x0f > +#define AUDIO_1_RATIO_MASK 0x0f > + > +#define AUDIO0_SEL_MASK 0xf > +#define AUDIO1_SEL_MASK 0xf > + > +#define CLK_SRC_SCLK_EPLL 0x7 > +#define CLK_SRC_MOUT_EPLL (1<<12) > +#define AUDIO_CLKMUX_ASS (1<<0) > + > +/* CON0 bit-fields */ > +#define EPLL_CON0_MDIV_MASK 0x1ff > +#define EPLL_CON0_PDIV_MASK 0x3f > +#define EPLL_CON0_SDIV_MASK 0x7 > +#define EPLL_CON0_MDIV_SHIFT 16 > +#define EPLL_CON0_PDIV_SHIFT 8 > +#define EPLL_CON0_SDIV_SHIFT 0 > +#define EPLL_CON0_LOCK_DET_EN_SHIFT 28 > +#define EPLL_CON0_LOCK_DET_EN_MASK 1 > + > +#define MPLL_FOUT_SEL_MASK 0x1 > +#define BPLL_FOUT_SEL_SHIFT 0 > +#define BPLL_FOUT_SEL_MASK 0x1 > +#endif > diff --git a/configs/odroid-xu3_defconfig > b/configs/odroid-xu3_defconfig new file mode 100644 > index 0000000..74aa0cf > --- /dev/null > +++ b/configs/odroid-xu3_defconfig > @@ -0,0 +1,4 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_EXYNOS=y > +CONFIG_TARGET_ODROID_XU3=y > +CONFIG_DEFAULT_DEVICE_TREE="exynos5422-odroidxu3" > diff --git a/include/configs/odroid_xu3.h > b/include/configs/odroid_xu3.h new file mode 100644 > index 0000000..f0d5646 > --- /dev/null > +++ b/include/configs/odroid_xu3.h > @@ -0,0 +1,243 @@ > +/* > + * Copyright (C) 2013 Samsung Electronics > + * Hyungwon Hwang <human.hw...@samsung.com> > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __CONFIG_ODROID_XU3_H > +#define __CONFIG_ODROID_XU3_H > + > +#include "exynos5-common.h" > + > +#define CONFIG_SYS_PROMPT "ODROID-XU3 # " > + > +/* High Level Configuration Options */ > +#include <asm/arch/cpu.h> /* get chip and board defs > */ + > +#define CONFIG_OF_CONTROL > +#define CONFIG_OF_SEPARATE In the newest u-boot CONFIG_OF_{CONTROL|SEPARATE} are already defined in the _defconfig and hence not needed here. > +#define CONFIG_BOARD_COMMON > + > +#define CONFIG_ARCH_CPU_INIT > +#define CONFIG_DISPLAY_CPUINFO > +#define CONFIG_DISPLAY_BOARDINFO > + > +/* Power Management is enabled */ > +#define CONFIG_PM > +#define CONFIG_PM_VDD_ARM 1.00 > +#define CONFIG_PM_VDD_KFC 1.0250 > +#define CONFIG_PM_VDD_INT 1.00 > +#define CONFIG_PM_VDD_G3D 1.00 > +#define CONFIG_PM_VDD_MIF 1.10 > + > +/* Keep L2 Cache Disabled */ > +#define CONFIG_SYS_DCACHE_OFF > + > +#define CONFIG_SYS_SDRAM_BASE 0x40000000 > +#define CONFIG_SYS_TEXT_BASE 0x43E00000 > +#define CONFIG_SPL_TEXT_BASE 0x02027000 > + > +/* input clock of PLL: SMDK5422 has 24MHz input clock */ > +#define CONFIG_SYS_CLK_FREQ 24000000 > + > +#define CONFIG_SETUP_MEMORY_TAGS > +#define CONFIG_CMDLINE_TAG > +#define CONFIG_INITRD_TAG > +#define CONFIG_REVISION_TAG > +#define CONFIG_CMDLINE_EDITING > + > +/* iRAM information */ > +#define CONFIG_PHY_IRAM_BASE (0x02020000) > +#define CONFIG_PHY_IRAM_NS_BASE (CONFIG_PHY_IRAM_BASE + > 0x53000) + > +/* Power Down Modes */ > +#define S5P_CHECK_SLEEP 0x00000BAD > +#define S5P_CHECK_DIDLE 0xBAD00000 > +#define S5P_CHECK_LPA 0xABAD0000 > + > +/* Offset for OM status registers */ > +#define OM_STATUS_OFFSET 0x0 > + > +/* select serial console configuration */ > +#define CONFIG_SERIAL_MULTI > +#define CONFIG_SERIAL2 /* use SERIAL 2 */ > +#define CONFIG_BAUDRATE 115200 > +#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 > + > +#define TZPC_BASE_OFFSET 0x10000 > + > +/* SD/MMC configuration */ > +#define CONFIG_GENERIC_MMC > +#define CONFIG_MMC > +#define CONFIG_SDHCI > +#define CONFIG_S5P_MSHC > +#define CONFIG_S5P_SDHCI > +#define CONFIG_MMC_64BIT_BUS > + > +#if defined(CONFIG_S5P_MSHC) > +#define CONFIG_MMC_EARLY_INIT > +#define MMC_MAX_CHANNEL 4 > +#define USE_MMC0 > +#define USE_MMC2 > + > +#define PHASE_DEVIDER 4 > + > +#define SDR_CH0 0x03030002 > +#define DDR_CH0 0x03020001 > + > +#define SDR_CH2 0x03020001 > +#define DDR_CH2 0x03030002 > + > +#define SDR_CH4 0x0 > +#define DDR_CH4 0x0 > +#endif > + > +/* > + * Boot configuration > + */ > +#define BOOT_MMCSD 0x3 > +#define BOOT_EMMC 0x6 > +#define BOOT_EMMC_4_4 0x7 > + > +/* > + * Boot device > + */ > +#define SDMMC_CH2 0x0 > +#define SDMMC_CH0 0x4 > +#define EMMC 0x14 > + > +#define CONFIG_BOARD_EARLY_INIT_F > + > +/* PWM */ > +#define CONFIG_PWM > + > +/* allow to overwrite serial and ethaddr */ > +#define CONFIG_ENV_OVERWRITE > + > +/* Command definition*/ > +#include <config_cmd_default.h> > + > +#define CONFIG_CMD_PING > +#define CONFIG_CMD_ELF > +#define CONFIG_CMD_MMC > +#define CONFIG_CMD_EXT2 > +#define CONFIG_CMD_FAT > +#define CONFIG_CMD_BOOTZ > + > +#define CONFIG_BOOTDELAY 3 > +#define CONFIG_ZERO_BOOTDELAY_CHECK > + > +/* USB */ > +#define CONFIG_CMD_USB > +#define CONFIG_USB_EHCI > +#define CONFIG_USB_EHCI_EXYNOS > +#define CONFIG_USB_STORAGE > + > +/* OHCI : Host 1.0 */ > +#define CONFIG_USB_OHCI > + > +/* Miscellaneous configurable options */ > +#define CONFIG_SYS_LONGHELP /* undef to save memory */ > +#define CONFIG_SYS_HUSH_PARSER /* use "hush" command > parser */ + > +#define CONFIG_SYS_CBSIZE 256 /* Console I/O > Buffer Size */ +#define CONFIG_SYS_PBSIZE > 384 /* Print Buffer Size */ +#define > CONFIG_SYS_MAXARGS 16 /* max number of command > args */ +/* Boot Argument Buffer Size */ +#define > CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* memtest > works on */ +#define CONFIG_SYS_MEMTEST_START > CONFIG_SYS_SDRAM_BASE +#define CONFIG_SYS_MEMTEST_END > (CONFIG_SYS_SDRAM_BASE + 0x5E00000) +#define > CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + > 0x3E00000) + +#define CONFIG_SYS_HZ 1000 > + > +#define CONFIG_RD_LVL > + > +/* Stack sizes */ > +#define CONFIG_STACKSIZE (256 << 10) /* 256KB > */ + > +/* > + * FIXME: The number of bank is actually 8. But there is no way to > reserver the > + * last 16 Mib in the last bank now. So I just excluded the last bank > + * temporally. > + */ > +#define CONFIG_NR_DRAM_BANKS 7 > + > +#define SDRAM_BANK_SIZE (256UL << 20UL) /* 256 > MB */ + > +#define CONFIG_SYS_MONITOR_BASE 0x00000000 > + > +/* FLASH and environment organization */ > +#define CONFIG_SYS_NO_FLASH > +#undef CONFIG_CMD_IMLS > +#define CONFIG_IDENT_STRING " for ODROID-XU3" > + > +#define CONFIG_ENV_IS_IN_MMC > +#define CONFIG_SYS_MMC_ENV_DEV 0 > + > +/* Configuration of ENV size on mmc */ > +#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */ > + > +/* Configuration of ROOTFS_ATAGS */ > +#define CONFIG_ROOTFS_ATAGS > +#ifdef CONFIG_ROOTFS_ATAGS > +#ifdef CONFIG_EXTRA_ENV_SETTINGS > +#undef CONFIG_EXTRA_ENV_SETTINGS > +#endif > +#define CONFIG_EXTRA_ENV_SETTINGS "rootfslen= 100000" > +#endif > + > +/* U-boot copy size from boot Media to DRAM.*/ > +#define CONFIG_DOS_PARTITION > +#define CFG_PARTITION_START 0x4000000 > +#define CONFIG_IRAM_STACK 0x02074000 > + > +#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_LOAD_ADDR - > 0x1000000) + > +/* Base address for secondary boot information */ > +#define CONFIG_SECONDARY_BOOT_INFORM_BASE > (CONFIG_SYS_TEXT_BASE - 0x8) + > +/* Offset for pmu reset status */ > +#define RST_STAT_OFFSET 0x404 > + > +/* RST_STAT */ > +#define WRESET (1 << 10) > +#define SYS_WDTRESET (1 << 9) > +#define CONFIG_SKIP_LOWLEVEL_INIT > + > +/* FIXME: MUST BE REMOVED AFTER TMU IS TURNED ON */ > +#undef CONFIG_EXYNOS_TMU > +#undef CONFIG_TMU_CMD_DTT > + > +#define CONFIG_FDTDEC_MEMORY > + > +#undef CONFIG_ARCH_EARLY_INIT_R > +#undef CONFIG_EXYNOS_SPL > +#undef CONFIG_SILENT_CONSOLE > +#undef CONFIG_CROS_EC > +#undef CONFIG_CROS_EC_SPI > +#undef CONFIG_CROS_EC_I2C > +#undef CONFIG_CROS_EC_KEYB > +#undef CONFIG_CMD_CROS_EC > +#undef CONFIG_KEYBOARD > +#undef CONFIG_SPI_BOOTING > +#undef CONFIG_ENV_IS_IN_SPI_FLASH > +#undef CONFIG_SPI_FLASH > +#undef CONFIG_EXYNOS_SPI > +#undef CONFIG_CMD_SF > +#undef CONFIG_CMD_SPI > +#undef CONFIG_SPI_FLASH_WINBOND > +#undef CONFIG_SPI_FLASH_GIGADEVICE > +#undef CONFIG_OF_SPI > +#undef CONFIG_FIT_BEST_MATCH > +#undef CONFIG_USB_BOOTING > +#undef CONFIG_CMD_NET > +#undef CONFIG_SMC911X > +#undef CONFIG_CMD_PXE > +#undef CONFIG_MENU > +#undef CONFIG_ENV_IS_IN_SPI_FLASH > + > + > +#endif /* __CONFIG_H */ In the config file you have enabled many features. Do we need them all for basic use case? I assume that after build u-boot-mmc.bin size is less than 328 KiB and it will be possible to fit it into HardKernel's SD card layout. Please consult the following link for reference: http://odroid.com/dokuwiki/doku.php?id=en:odroid-xu3 Speaking about the SD card layout. I think that it would be welcome to see ./doc entry for XU3 similar to ./doc/README.odroid -- Best regards, Lukasz Majewski Samsung R&D Institute Poland (SRPOL) | Linux Platform Group _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot