Initialize retimer for XFI on t1024qds.

Signed-off-by: Shengzhou Liu <shengzhou....@freescale.com>
---
v2: no change.

 board/freescale/t102xqds/t102xqds.c | 57 +++++++++++++++++++++++++++++++++++++
 include/configs/T102xQDS.h          |  5 +++-
 2 files changed, 61 insertions(+), 1 deletion(-)

diff --git a/board/freescale/t102xqds/t102xqds.c 
b/board/freescale/t102xqds/t102xqds.c
index 013024e..ca8ce1e 100644
--- a/board/freescale/t102xqds/t102xqds.c
+++ b/board/freescale/t102xqds/t102xqds.c
@@ -186,6 +186,62 @@ static void board_mux_setup(void)
 }
 #endif
 
+void board_retimer_ds125df111_init(void)
+{
+       u8 reg;
+
+       /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
+       reg = I2C_MUX_CH7;
+       i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &reg, 1);
+       reg = I2C_MUX_CH5;
+       i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, &reg, 1);
+
+       /* Access to Control/Shared register */
+       reg = 0x0;
+       i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
+
+       /* Read device revision and ID */
+       i2c_read(I2C_RETIMER_ADDR, 1, 1, &reg, 1);
+       debug("Retimer version id = 0x%x\n", reg);
+
+       /* Enable Broadcast */
+       reg = 0x0c;
+       i2c_write(I2C_RETIMER_ADDR, 0xff, 1, &reg, 1);
+
+       /* Reset Channel Registers */
+       i2c_read(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
+       reg |= 0x4;
+       i2c_write(I2C_RETIMER_ADDR, 0, 1, &reg, 1);
+
+       /* Enable override divider select and Enable Override Output Mux */
+       i2c_read(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
+       reg |= 0x24;
+       i2c_write(I2C_RETIMER_ADDR, 9, 1, &reg, 1);
+
+       /* Select VCO Divider to full rate (000) */
+       i2c_read(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
+       reg &= 0x8f;
+       i2c_write(I2C_RETIMER_ADDR, 0x18, 1, &reg, 1);
+
+       /* Select active PFD MUX input as re-timed data (001) */
+       i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
+       reg &= 0x3f;
+       reg |= 0x20;
+       i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, &reg, 1);
+
+       /* Set data rate as 10.3125 Gbps */
+       reg = 0x0;
+       i2c_write(I2C_RETIMER_ADDR, 0x60, 1, &reg, 1);
+       reg = 0xb2;
+       i2c_write(I2C_RETIMER_ADDR, 0x61, 1, &reg, 1);
+       reg = 0x90;
+       i2c_write(I2C_RETIMER_ADDR, 0x62, 1, &reg, 1);
+       reg = 0xb3;
+       i2c_write(I2C_RETIMER_ADDR, 0x63, 1, &reg, 1);
+       reg = 0xcd;
+       i2c_write(I2C_RETIMER_ADDR, 0x64, 1, &reg, 1);
+}
+
 int board_early_init_r(void)
 {
 #ifdef CONFIG_SYS_FLASH_BASE
@@ -220,6 +276,7 @@ int board_early_init_r(void)
 #endif
        select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
        board_mux_lane_to_slot();
+       board_retimer_init();
 
        /* Increase IO drive strength to address FCS error on RGMII */
        out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800);
diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h
index d24e06e..78ed243 100644
--- a/include/configs/T102xQDS.h
+++ b/include/configs/T102xQDS.h
@@ -555,11 +555,14 @@ unsigned long get_board_ddr_clk(void);
 
 #define I2C_MUX_PCA_ADDR               0x77
 #define I2C_MUX_PCA_ADDR_PRI           0x77 /* Primary Mux*/
-
+#define I2C_MUX_PCA_ADDR_SEC            0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR               0x18
 
 /* I2C bus multiplexer */
 #define I2C_MUX_CH_DEFAULT      0x8
 #define I2C_MUX_CH_DIU         0xC
+#define I2C_MUX_CH5            0xD
+#define I2C_MUX_CH7            0xF
 
 /* LDI/DVI Encoder for display */
 #define CONFIG_SYS_I2C_LDI_ADDR         0x38
-- 
2.1.0.27.g96db324

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot

Reply via email to