This patch configures and initializes the L2 switch on T1040QDS board.
The L2 switch ports must be initialized according to the SerDes
protocols.
Signed-off-by: Codrin Ciubotariu <codrin.ciubota...@freescale.com>
Change-Id: I329f9cc1b1be745da23151e78831d8a3219b7f97
---
board/freescale/t1040qds/eth.c | 92 ++++++++++++++++++++++++++++++++++++++++++
include/configs/T1040QDS.h | 4 ++
2 files changed, 96 insertions(+)
diff --git a/board/freescale/t1040qds/eth.c b/board/freescale/t1040qds/eth.c
index 2f8e753..3345070 100644
--- a/board/freescale/t1040qds/eth.c
+++ b/board/freescale/t1040qds/eth.c
@@ -18,6 +18,9 @@
#include <fsl_mdio.h>
#include <malloc.h>
#include <asm/fsl_dtsec.h>
+#ifdef CONFIG_VSC9953
+#include <vsc9953.h>
+#endif
#include "../common/fman.h"
#include "../common/qixis.h"
@@ -493,6 +496,95 @@ int board_eth_init(bd_t *bis)
}
}
+#ifdef CONFIG_VSC9953
+ int lane;
+ int phy_addr;
+ phy_interface_t phy_int;
+ struct mii_dev *bus;
+
+ for (i = 0; i < VSC9953_MAX_PORTS; i++) {
+ lane = -1;
+ phy_addr = 0;
+ phy_int = PHY_INTERFACE_MODE_NONE;
+ switch (i) {
+ case 0:
+ case 1:
+ case 2:
+ case 3:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_A);
+ /* PHYs connected over QSGMII */
+ if (lane >= 0) {
+ phy_addr = CONFIG_SYS_FM1_QSGMII21_PHY_ADDR +
+ i;
+ phy_int = PHY_INTERFACE_MODE_QSGMII;
+ break;
+ }
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_SW1_MAC1 + i);
+
+ if (lane < 0)
+ break;
+
+ /* PHYs connected over QSGMII */
+ if (i != 3 || lane_to_slot[lane] == 7)
+ phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR
+ + i;
+ else
+ phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR;
+ phy_int = PHY_INTERFACE_MODE_SGMII;
+ break;
+ case 4:
+ case 5:
+ case 6:
+ case 7:
+ lane = serdes_get_first_lane(FSL_SRDS_1, QSGMII_SW1_B);
+ /* PHYs connected over QSGMII */
+ if (lane >= 0) {
+ phy_addr = CONFIG_SYS_FM1_QSGMII11_PHY_ADDR +
+ i - 4;
+ phy_int = PHY_INTERFACE_MODE_QSGMII;
+ break;
+ }
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_SW1_MAC1 + i);
+ /* PHYs connected over SGMII */
+ if (lane >= 0) {
+ phy_addr = CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR
+ + i - 3;
+ phy_int = PHY_INTERFACE_MODE_SGMII;
+ }
+ break;
+ case 8:
+ if (serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_FM1_DTSEC1) < 0)
+ /* FM1@DTSEC1 is connected to SW1@PORT8 */
+ vsc9953_port_enable(i);
+ break;
+ case 9:
+ if (serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_FM1_DTSEC2) < 0) {
+ /* Enable L2 On MAC2 using SCFG */
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)
+ CONFIG_SYS_MPC85xx_SCFG;
+
+ out_be32(&scfg->esgmiiselcr,
+ in_be32(&scfg->esgmiiselcr) |
+ (0x80000000));
+ vsc9953_port_enable(i);
+ }
+ break;
+ }
+
+ if (lane >= 0) {
+ bus = mii_dev_for_muxval(lane_to_slot[lane]);
+ vsc9953_port_info_set_mdio(i, bus);
+ vsc9953_port_enable(i);
+ }
+ vsc9953_port_info_set_phy_address(i, phy_addr);
+ vsc9953_port_info_set_phy_int(i, phy_int);
+ }
+
+#endif
cpu_eth_init(bis);
#endif
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index 6b396bb..8e6f946 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -673,6 +673,10 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
+#define CONFIG_VSC9953_CMD
+#define CONFIG_SYS_FM1_QSGMII11_PHY_ADDR 0x14
+#define CONFIG_SYS_FM1_QSGMII21_PHY_ADDR 0x18
+
/*
* Dynamic MTD Partition support with mtdparts
*/
--
1.7.11.7
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
