Am Montag 22 Juni 2009 14:53:44 schrieb André Schwarz: > On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote: > > André, > > > > > Dieter, > > > > > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote: > > > > Hi all, > > > > > > > > I've tried the first time booting a self compiled u-boot from > > > > git.marvell.com U-Boot can be downloaded and started with openocd > > > > quite well. > > > > Boot messages (version is dirty due to a comment in board file): > > > > > > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) > > > > Marvell-Sheevaplug > > > > > > > > SoC: Kirkwood 88F6281_A0 > > > > DRAM: 512 MB > > > > NAND: 512 MiB > > > > *** Warning - bad CRC or NAND, using default environment > > > > > > most propably you'll need to save the environment. > > > > Also saving environment doesn't help. > > The bad CRC message disappered as expected but that's all what happened. > > > > > > In: serial > > > > Out: serial > > > > Err: serial > > > > Net: egiga0 > > > > 88E1116 Initialized on egiga0 > > > > Hit any key to stop autoboot: 0 > > > > Marvell>> > > > > > > type "save" here and "reset". > > > > > > > Environment is broken only with marvell git u-boot. Preflashed u-boot > > > > find environment is ok. > > > > Does sheevaplug u-boot from marvell git use other environment > > > > settings than preflashed u-boot? > > > > > > > > Marvell>> printenv > > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} > > > > ${x_bootargs_root}; bootm 0x6400000; > > > > bootdelay=3 > > > > baudrate=115200 > > > > x_bootargs=console=ttyS0,115200 > > > > mtdparts=orion_nand:512k(uboot),3...@1m(kernel),1...@4m(psm),1...@5m(rootf > > > >s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000 > > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2 > > > > stdin=serial > > > > stdout=serial > > > > stderr=serial > > > > ethaddr=00:50:43:e0:b9:d8 > > > > ethact=egiga0 > > > > ipaddr=192.168.2.75 > > > > > > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75) > > Did you try "bootp" or "dhcp" to set up the I/F ? > Yes, but everytimes the same: Marvell>> dhcp BOOTP broadcast 1
... machine hangs and only a reset helps... U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45) Marvell-Sheevaplug SoC: Kirkwood 88F6281_A0 DRAM: 512 MB NAND: 512 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Net: egiga0 88E1116 Initialized on egiga0 Hit any key to stop autoboot: 0 Marvell>> bootp BOOTP broadcast 1 ...the same here again... It seems that the network would be activated (1 blink on the activity LED) but nothing more happens. > > > > If I now try to ping another machine in the same network: > > > > Marvell>> ping 192.168.2.251 > > > > Using egiga0 device > > > > > > maybe your MAC is missing ? environment ? > > > > MAC is available in default (compiled in environment) as shown in env above: > > > > ethaddr=00:50:43:e0:b9:d8 > > > > Also writing a new MAC to environment / savenenv / reset made no > > difference :( > > > > > > This is all what happens - no response from board, CTRL-C doesn't > > > > work. Only a hard reset will get the board up again. > > > > > > > > Do I have to change something in the default board configuration to > > > > succesfullly use networking on the sheevaplug? > > > > > > > > u-boot is build with following commands: > > > > > > > > make ARCH=arm sheevaplug_config > > > > make > > > > > > > > I get no errors during build. > > > > > > > > My gcc version is: > > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease) > > > > > > > > Any help would be appreciated, > > > > Dieter > > > > > > Regards, > > > > > > André > > > > Dieter > > > > > > _______________________________________________ > > > > U-Boot mailing list > > > > U-Boot@lists.denx.de > > > > http://lists.denx.de/mailman/listinfo/u-boot > > > > > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler > > > Registergericht: Amtsgericht Stuttgart, HRB 271090 > > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, > > > Hans-Joachim Reich > > MATRIX VISION GmbH, Talstra�e 16, DE-71570 Oppenweiler > Registergericht: Amtsgericht Stuttgart, HRB 271090 > Gesch�ftsf�hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, > Hans-Joachim Reich
_______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot