Signed-off-by: Albert ARIBAUD (3ADEV) <albert.arib...@3adev.fr>
---
arch/arm/cpu/arm926ejs/lpc32xx/devices.c | 6 ++
arch/arm/include/asm/arch-lpc32xx/clk.h | 3 +
arch/arm/include/asm/arch-lpc32xx/sys_proto.h | 1 +
drivers/spi/Makefile | 1 +
drivers/spi/lpc32xx_ssp.c | 132 ++++++++++++++++++++++++++
5 files changed, 143 insertions(+)
create mode 100644 drivers/spi/lpc32xx_ssp.c
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
index 81b53ea..56ce9ab 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/devices.c
@@ -61,3 +61,9 @@ void lpc32xx_i2c_init(unsigned int devnum)
ctrl |= CLK_I2C2_ENABLE;
writel(ctrl, &clk->i2cclk_ctrl);
}
+
+void lpc32xx_ssp_init(void)
+{
+ /* Enable SSP0 interface */
+ writel(CLK_SSP0_ENABLE_CLOCK, &clk->ssp_ctrl);
+}
diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h
b/arch/arm/include/asm/arch-lpc32xx/clk.h
index 781ac07..2cb5703 100644
--- a/arch/arm/include/asm/arch-lpc32xx/clk.h
+++ b/arch/arm/include/asm/arch-lpc32xx/clk.h
@@ -155,6 +155,9 @@ struct clk_pm_regs {
#define CLK_NAND_MLC (1 << 1)
#define CLK_NAND_MLC_INT (1 << 5)
+/* SSP Clock Control Register bits */
+#define CLK_SSP0_ENABLE_CLOCK (1 << 0)
+
unsigned int get_sys_clk_rate(void);
unsigned int get_hclk_pll_rate(void);
unsigned int get_hclk_clk_div(void);
diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
index a4a05d1..86d5ee9 100644
--- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
@@ -11,5 +11,6 @@ void lpc32xx_uart_init(unsigned int uart_id);
void lpc32xx_mac_init(void);
void lpc32xx_mlc_nand_init(void);
void lpc32xx_i2c_init(unsigned int devnum);
+void lpc32xx_ssp_init(void);
#endif /* _LPC32XX_SYS_PROTO_H */
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index edbd520..ce6f1cc 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o
obj-$(CONFIG_ICH_SPI) += ich.o
obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
+obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
obj-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o
obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
obj-$(CONFIG_MXC_SPI) += mxc_spi.o
diff --git a/drivers/spi/lpc32xx_ssp.c b/drivers/spi/lpc32xx_ssp.c
new file mode 100644
index 0000000..40270df
--- /dev/null
+++ b/drivers/spi/lpc32xx_ssp.c
@@ -0,0 +1,132 @@
+/*
+ * LPC32xx SSP interface (SPI mode)
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.arib...@3adev.fr>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/compat.h>
+#include <asm/io.h>
+#include <malloc.h>
+#include <spi.h>
+#include <asm/arch/clk.h>
+
+/* SSP chip registers */
+struct ssp_regs {
+ u32 cr0;
+ u32 cr1;
+ u32 data;
+ u32 sr;
+ u32 cpsr;
+ u32 imsc;
+ u32 ris;
+ u32 mis;
+ u32 icr;
+ u32 dmacr;
+};
+
+/* CR1 register defines */
+#define SSP_CR1_SSP_ENABLE 0x0002
+
+/* SR register defines */
+#define SSP_SR_TNF 0x0002
+/* SSP status RX FIFO not empty bit */
+#define SSP_SR_RNE 0x0004
+
+static struct ssp_regs *ssp0_regs = (struct ssp_regs *)SSP0_BASE;
+
+static struct spi_slave ssp0_slave = {
+ .bus = 0,
+ .cs = 0,
+ .op_mode_rx = 0,
+ .op_mode_tx = 0,
+ .wordlen = 8,
+ .max_write_size = 1, /* this is for SPI FLASHes -- don't care */
+ .memory_map = NULL, /* for SPI FLASHes too */
+ .option = 0,
+ .flags = 0
+};
+
+/* spi_init is called during boot when CONFIG_CMD_SPI is defined */
+void spi_init(void)
+{
+ /*
+ * nothing to do: clocking was enabled in lpc32xx_ssp_enable()
+ * and configuration will be done in spi_setup_slave()
+ */
+}
+
+/* the following is called in sequence by do_spi_xfer() */
+
+struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode)
+{
+ /* we only set up SSP0 for now, so ignore bus */
+
+ if (mode & SPI_3WIRE) {
+ error("3-wire mode not supported");
+ return NULL;
+ }
+
+ if (mode & SPI_SLAVE) {
+ error("slave mode not supported\n");
+ return NULL;
+ }
+
+ if (mode & SPI_PREAMBLE) {
+ error("preamble byte skipping not supported\n");
+ return NULL;
+ }
+
+ /*
+ * 8 bit frame, SPI fmt, 500kbps -> clock divider is 26.
+ * Set SCR to 0 and CPSDVSR to 26.
+ */
+
+ writel(0x7, &ssp0_regs->cr0); /* 8-bit chunks, SPI, 1 clk/bit */
+ writel(26, &ssp0_regs->cpsr); /* SSP clock = HCLK/26 = 500kbps */
+ writel(0, &ssp0_regs->imsc); /* do not raise any interrupts */
+ writel(0, &ssp0_regs->icr); /* clear any pending interrupt */
+ writel(0, &ssp0_regs->dmacr); /* do not do DMAs */
+ writel(SSP_CR1_SSP_ENABLE, &ssp0_regs->cr1); /* enable SSP0 */
+ return &ssp0_slave;
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+ /* only one bus and slave so far, always available */
+ return 0;
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ int bytelen = bitlen >> 3;
+ int idx_out = 0;
+ int idx_in = 0;
+ int start_time;
+
+ start_time = get_timer(0);
+ while ((idx_out < bytelen) || (idx_in < bytelen)) {
+ int status = readl(&ssp0_regs->sr);
+ if ((idx_out < bytelen) && (status & SSP_SR_TNF))
+ writel(((u8 *)dout)[idx_out++], &ssp0_regs->data);
+ if ((idx_in < bytelen) && (status & status & SSP_SR_RNE))
+ ((u8 *)din)[idx_in++] = readl(&ssp0_regs->data);
+ if (get_timer(start_time) >= CONFIG_LPC32XX_SSP_TIMEOUT)
+ return -1;
+ }
+ return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+ /* do nothing */
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+ /* do nothing */
+}
--
2.1.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
