This patch groups some macros defined for registers and
replaces some magic numbers from vsc9953 with macros. Also,
"port" and "port_nr" keywords are replaced with "port_no".
Also, in some places, this patch replaces in_le32 and out_le32
with clrbits_le32 and setbits_le32 to reduce the number of code
lines and to assure that only intended bits of a register are
changed.
Signed-off-by: Codrin Ciubotariu <codrin.ciubota...@freescale.com>
Change-Id: Ib5f7d94bd6a39b909bf7b70bb12e15156a7e45c9
---
drivers/net/vsc9953.c | 100 +++++++++++++++++++++++++-------------------------
include/vsc9953.h | 47 ++++++++++++++++++++----
2 files changed, 88 insertions(+), 59 deletions(-)
diff --git a/drivers/net/vsc9953.c b/drivers/net/vsc9953.c
index fed7358..720ae47 100644
--- a/drivers/net/vsc9953.c
+++ b/drivers/net/vsc9953.c
@@ -25,44 +25,44 @@ static struct vsc9953_info vsc9953_l2sw = {
.port[9] = VSC9953_PORT_INFO_INITIALIZER(9),
};
-void vsc9953_port_info_set_mdio(int port, struct mii_dev *bus)
+void vsc9953_port_info_set_mdio(int port_no, struct mii_dev *bus)
{
- if (!VSC9953_PORT_CHECK(port))
+ if (!VSC9953_PORT_CHECK(port_no))
return;
- vsc9953_l2sw.port[port].bus = bus;
+ vsc9953_l2sw.port[port_no].bus = bus;
}
-void vsc9953_port_info_set_phy_address(int port, int address)
+void vsc9953_port_info_set_phy_address(int port_no, int address)
{
- if (!VSC9953_PORT_CHECK(port))
+ if (!VSC9953_PORT_CHECK(port_no))
return;
- vsc9953_l2sw.port[port].phyaddr = address;
+ vsc9953_l2sw.port[port_no].phyaddr = address;
}
-void vsc9953_port_info_set_phy_int(int port, phy_interface_t phy_int)
+void vsc9953_port_info_set_phy_int(int port_no, phy_interface_t phy_int)
{
- if (!VSC9953_PORT_CHECK(port))
+ if (!VSC9953_PORT_CHECK(port_no))
return;
- vsc9953_l2sw.port[port].enet_if = phy_int;
+ vsc9953_l2sw.port[port_no].enet_if = phy_int;
}
-void vsc9953_port_enable(int port)
+void vsc9953_port_enable(int port_no)
{
- if (!VSC9953_PORT_CHECK(port))
+ if (!VSC9953_PORT_CHECK(port_no))
return;
- vsc9953_l2sw.port[port].enabled = 1;
+ vsc9953_l2sw.port[port_no].enabled = 1;
}
-void vsc9953_port_disable(int port)
+void vsc9953_port_disable(int port_no)
{
- if (!VSC9953_PORT_CHECK(port))
+ if (!VSC9953_PORT_CHECK(port_no))
return;
- vsc9953_l2sw.port[port].enabled = 0;
+ vsc9953_l2sw.port[port_no].enabled = 0;
}
static void vsc9953_mdio_write(struct vsc9953_mii_mng *phyregs, int port_addr,
@@ -148,21 +148,21 @@ static int init_phy(struct eth_device *dev)
return 0;
}
-static int vsc9953_port_init(int port)
+static int vsc9953_port_init(int port_no)
{
struct eth_device *dev;
/* Internal ports never have a PHY */
- if (VSC9953_INTERNAL_PORT_CHECK(port))
+ if (VSC9953_INTERNAL_PORT_CHECK(port_no))
return 0;
/* alloc eth device */
dev = (struct eth_device *)calloc(1, sizeof(struct eth_device));
if (!dev)
- return 1;
+ return -1;
- sprintf(dev->name, "SW@PORT%d", port);
- dev->priv = &vsc9953_l2sw.port[port];
+ sprintf(dev->name, "SW@PORT%d", port_no);
+ dev->priv = &vsc9953_l2sw.port[port_no];
dev->init = NULL;
dev->halt = NULL;
dev->send = NULL;
@@ -170,7 +170,7 @@ static int vsc9953_port_init(int port)
if (init_phy(dev)) {
free(dev);
- return 1;
+ return -1;
}
return 0;
@@ -255,8 +255,8 @@ void vsc9953_init(bd_t *bis)
out_le32(&l2dev_gmii_reg->mac_cfg_status.mac_hdx_cfg, hdx_cfg);
out_le32(&l2sys_reg->sys.front_port_mode[i],
CONFIG_VSC9953_FRONT_PORT_MODE);
- out_le32(&l2qsys_reg->sys.switch_port_mode[i],
- CONFIG_VSC9953_PORT_ENA);
+ setbits_le32(&l2qsys_reg->sys.switch_port_mode[i],
+ CONFIG_VSC9953_PORT_ENA);
out_le32(&l2dev_gmii_reg->mac_cfg_status.mac_maxlen_cfg,
CONFIG_VSC9953_MAC_MAX_LEN);
out_le32(&l2sys_reg->pause_cfg.pause_cfg[i],
@@ -312,25 +312,23 @@ void vsc9953_init(bd_t *bis)
#ifdef CONFIG_VSC9953_CMD
/* Enable/disable status of a VSC9953 port */
-static void vsc9953_port_status_set(int port_nr, u8 enabled)
+static void vsc9953_port_status_set(int port_no, u8 enabled)
{
- u32 val;
struct vsc9953_qsys_reg *l2qsys_reg;
/* Administrative down */
- if (vsc9953_l2sw.port[port_nr].enabled == 0)
+ if (!vsc9953_l2sw.port[port_no].enabled)
return;
l2qsys_reg = (struct vsc9953_qsys_reg *)(VSC9953_OFFSET +
VSC9953_QSYS_OFFSET);
- val = in_le32(&l2qsys_reg->sys.switch_port_mode[port_nr]);
- if (enabled == 1)
- val |= (1 << 13);
+ if (enabled)
+ setbits_le32(&l2qsys_reg->sys.switch_port_mode[port_no],
+ CONFIG_VSC9953_PORT_ENA);
else
- val &= ~(1 << 13);
-
- out_le32(&l2qsys_reg->sys.switch_port_mode[port_nr], val);
+ clrbits_le32(&l2qsys_reg->sys.switch_port_mode[port_no],
+ CONFIG_VSC9953_PORT_ENA);
}
/* Set all VSC9953 ports' status */
@@ -343,14 +341,14 @@ static void vsc9953_port_all_status_set(u8 enabled)
}
/* Start autonegotiation for a VSC9953 PHY */
-static void vsc9953_phy_autoneg(int port_nr)
+static void vsc9953_phy_autoneg(int port_no)
{
- if (!vsc9953_l2sw.port[port_nr].phydev)
+ if (!vsc9953_l2sw.port[port_no].phydev)
return;
- if (vsc9953_l2sw.port[port_nr].phydev->drv->startup(
- vsc9953_l2sw.port[port_nr].phydev))
- printf("Failed to start PHY for port %d\n", port_nr);
+ if (vsc9953_l2sw.port[port_no].phydev->drv->startup(
+ vsc9953_l2sw.port[port_no].phydev))
+ printf("Failed to start PHY for port %d\n", port_no);
}
/* Start autonegotiation for all VSC9953 PHYs */
@@ -363,7 +361,7 @@ static void vsc9953_phy_all_autoneg(void)
}
/* Print a VSC9953 port's configuration */
-static void vsc9953_port_config_show(int port)
+static void vsc9953_port_config_show(int port_no)
{
int speed;
int duplex;
@@ -375,20 +373,20 @@ static void vsc9953_port_config_show(int port)
l2qsys_reg = (struct vsc9953_qsys_reg *)(VSC9953_OFFSET +
VSC9953_QSYS_OFFSET);
- val = in_le32(&l2qsys_reg->sys.switch_port_mode[port]);
- enabled = vsc9953_l2sw.port[port].enabled &
- ((val & 0x00002000) >> 13);
+ val = in_le32(&l2qsys_reg->sys.switch_port_mode[port_no]);
+ enabled = !!(vsc9953_l2sw.port[port_no].enabled &
+ val & CONFIG_VSC9953_PORT_ENA);
/* internal ports (8 and 9) are fixed */
- if (VSC9953_INTERNAL_PORT_CHECK(port)) {
+ if (VSC9953_INTERNAL_PORT_CHECK(port_no)) {
link = 1;
speed = SPEED_2500;
duplex = DUPLEX_FULL;
} else {
- if (vsc9953_l2sw.port[port].phydev) {
- link = vsc9953_l2sw.port[port].phydev->link;
- speed = vsc9953_l2sw.port[port].phydev->speed;
- duplex = vsc9953_l2sw.port[port].phydev->duplex;
+ if (vsc9953_l2sw.port[port_no].phydev) {
+ link = vsc9953_l2sw.port[port_no].phydev->link;
+ speed = vsc9953_l2sw.port[port_no].phydev->speed;
+ duplex = vsc9953_l2sw.port[port_no].phydev->duplex;
} else {
link = -1;
speed = -1;
@@ -396,7 +394,7 @@ static void vsc9953_port_config_show(int port)
}
}
- printf("%8d ", port);
+ printf("%8d ", port_no);
printf("%8s ", enabled == 1 ? "enabled" : "disabled");
printf("%8s ", link == 1 ? "up" : "down");
@@ -487,11 +485,11 @@ static int do_ethsw(cmd_tbl_t *cmdtp, int flag, int argc,
char * const argv[])
U_BOOT_CMD(ethsw, 5, 0, do_ethsw,
"vsc9953 l2 switch commands",
- "port <port_nr> enable|disable\n"
+ "port <port_no> enable|disable\n"
" - enable/disable an l2 switch port\n"
- " port_nr=0..9; use \"all\" for all ports\n"
- "ethsw port <port_nr> show\n"
+ " port_no=0..9; use \"all\" for all ports\n"
+ "ethsw port <port_no> show\n"
" - show an l2 switch port's configuration\n"
- " port_nr=0..9; use \"all\" for all ports\n"
+ " port_no=0..9; use \"all\" for all ports\n"
);
#endif /* CONFIG_VSC9953_CMD */
diff --git a/include/vsc9953.h b/include/vsc9953.h
index 3d11b87..920402f 100644
--- a/include/vsc9953.h
+++ b/include/vsc9953.h
@@ -33,29 +33,60 @@
#define T1040_SWITCH_GMII_DEV_OFFSET 0x010000
#define VSC9953_PHY_REGS_OFFST 0x0000AC
+/* Macros for vsc9953_chip_regs.soft_rst register */
#define CONFIG_VSC9953_SOFT_SWC_RST_ENA 0x00000001
+
+/* Macros for vsc9953_sys_sys.reset_cfg register */
#define CONFIG_VSC9953_CORE_ENABLE 0x80
#define CONFIG_VSC9953_MEM_ENABLE 0x40
#define CONFIG_VSC9953_MEM_INIT 0x20
-#define CONFIG_VSC9953_PORT_ENA 0x00003a00
+/* Macros for vsc9953_dev_gmii_mac_cfg_status.mac_ena_cfg register */
#define CONFIG_VSC9953_MAC_ENA_CFG 0x00000011
+
+/* Macros for vsc9953_dev_gmii_mac_cfg_status.mac_mode_cfg register */
#define CONFIG_VSC9953_MAC_MODE_CFG 0x00000011
+
+/* Macros for vsc9953_dev_gmii_mac_cfg_status.mac_ifg_cfg register */
#define CONFIG_VSC9953_MAC_IFG_CFG 0x00000515
+
+/* Macros for vsc9953_dev_gmii_mac_cfg_status.mac_hdx_cfg register */
#define CONFIG_VSC9953_MAC_HDX_CFG 0x00001043
+
+/* Macros for vsc9953_dev_gmii_mac_cfg_status.mac_maxlen_cfg register */
+#define CONFIG_VSC9953_MAC_MAX_LEN 0x000005ee
+
+/* Macros for vsc9953_dev_gmii_port_mode.clock_cfg register */
#define CONFIG_VSC9953_CLOCK_CFG 0x00000001
#define CONFIG_VSC9953_CLOCK_CFG_1000M 0x00000001
+
+/* Macros for vsc9953_sys_sys.front_port_mode register */
+#define CONFIG_VSC9953_FRONT_PORT_MODE 0x00000000
+
+/* Macros for vsc9953_ana_pfc.pfc_cfg register */
#define CONFIG_VSC9953_PFC_FC 0x00000001
#define CONFIG_VSC9953_PFC_FC_QSGMII 0x00000000
+
+/* Macros for vsc9953_sys_pause_cfg.mac_fc_cfg register */
#define CONFIG_VSC9953_MAC_FC_CFG 0x04700000
#define CONFIG_VSC9953_MAC_FC_CFG_QSGMII 0x00700000
+
+/* Macros for vsc9953_sys_pause_cfg.pause_cfg register */
#define CONFIG_VSC9953_PAUSE_CFG 0x001ffffe
+
+/* Macros for vsc9953_sys_pause_cfg.pause_cfg register */
+#define CONFIG_VSC9953_PAUSE_CFG 0x001ffffe
+
+/* Macros for vsc9953_sys_pause_cfgtot_tail_drop_lvl register */
#define CONFIG_VSC9953_TOT_TAIL_DROP_LVL 0x000003ff
-#define CONFIG_VSC9953_FRONT_PORT_MODE 0x00000000
-#define CONFIG_VSC9953_MAC_MAX_LEN 0x000005ee
+/* Macros for vsc9953_vcap_core_cfg.vcap_mv_cfg register */
#define CONFIG_VSC9953_VCAP_MV_CFG 0x0000ffff
#define CONFIG_VSC9953_VCAP_UPDATE_CTRL 0x01000004
+
+/* Macros for vsc9953_qsys_sys.switch_port_mode register */
+#define CONFIG_VSC9953_PORT_ENA 0x00002000
+
#define VSC9953_MAX_PORTS 10
#define VSC9953_PORT_CHECK(port) \
(((port) < 0 || (port) >= VSC9953_MAX_PORTS) ? 0 : 1)
@@ -393,10 +424,10 @@ struct vsc9953_info {
void vsc9953_init(bd_t *bis);
-void vsc9953_port_info_set_mdio(int port, struct mii_dev *bus);
-void vsc9953_port_info_set_phy_address(int port, int address);
-void vsc9953_port_enable(int port);
-void vsc9953_port_disable(int port);
-void vsc9953_port_info_set_phy_int(int port, phy_interface_t phy_int);
+void vsc9953_port_info_set_mdio(int port_no, struct mii_dev *bus);
+void vsc9953_port_info_set_phy_address(int port_no, int address);
+void vsc9953_port_enable(int port_no);
+void vsc9953_port_disable(int port_no);
+void vsc9953_port_info_set_phy_int(int port_no, phy_interface_t phy_int);
#endif /* _VSC9953_H_ */
--
1.9.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
