At present minnowmax does not correct set up PCI interrupts. This should be
done in U-Boot so that devices work correctly in Linux.
Note: This code needs to make use of the recent pirq_routing work. It does
not seem to support all the required features, so this RFC will hopefully
help figure this out.
Signed-off-by: Simon Glass <s...@chromium.org>
---
arch/x86/cpu/baytrail/valleyview.c | 492 +++++++++++++++++++++++++++++++++++++
arch/x86/dts/minnowmax.dts | 28 +++
include/configs/minnowmax.h | 1 +
3 files changed, 521 insertions(+)
diff --git a/arch/x86/cpu/baytrail/valleyview.c
b/arch/x86/cpu/baytrail/valleyview.c
index f1c3578..efbb4a5 100644
--- a/arch/x86/cpu/baytrail/valleyview.c
+++ b/arch/x86/cpu/baytrail/valleyview.c
@@ -5,9 +5,14 @@
*/
#include <common.h>
+#include <dm.h>
#include <mmc.h>
#include <pci_ids.h>
+#include <asm/interrupt.h>
+#include <asm/irq.h>
+#include <asm/ioapic.h>
#include <asm/post.h>
+#include <asm/fsp/fsp_support.h>
static struct pci_device_id mmc_supported[] = {
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_VALLEYVIEW_SDIO },
@@ -37,3 +42,490 @@ int arch_cpu_init(void)
return 0;
}
#endif
+
+/*
+ * TODO(sjg): This code comes from coreboot's fsp_baytrail/southcluster.c. It
+ * has been cleaned up a little but still has macro stuff like
+ * PCI_DEV_PIRQ_ROUTE and doesn't use device tree. It needs to be adjusted to
+ * fit with the existing pirq-routing code. However it isn't clear that that
+ * code has all the required features.
+ *
+ * PIC IRQ settings
+ */
+#define PIRQ_PIC_IRQ3 0x3
+#define PIRQ_PIC_IRQ4 0x4
+#define PIRQ_PIC_IRQ5 0x5
+#define PIRQ_PIC_IRQ6 0x6
+#define PIRQ_PIC_IRQ7 0x7
+#define PIRQ_PIC_IRQ9 0x9
+#define PIRQ_PIC_IRQ10 0xa
+#define PIRQ_PIC_IRQ11 0xb
+#define PIRQ_PIC_IRQ12 0xc
+#define PIRQ_PIC_IRQ14 0xe
+#define PIRQ_PIC_IRQ15 0xf
+#define PIRQ_PIC_IRQDISABLE 0x80
+
+#define PCI_DEV_PIRQ_ROUTE(dev_, a_, b_, c_, d_) \
+ [dev_] = ((PIRQ ## d_) << 12) | ((PIRQ ## c_) << 8) | \
+ ((PIRQ ## b_) << 4) | ((PIRQ ## a_) << 0)
+
+#define PIRQ_PIC(pirq_, pic_irq_) \
+ [PIRQ ## pirq_] = PIRQ_PIC_IRQ ## pic_irq_
+
+#define NUM_OF_PCI_DEVS 32
+#define NUM_PIRQS 8
+
+struct baytrail_irq_route {
+ /* Per-device configuration */
+ uint16_t pcidev[NUM_OF_PCI_DEVS];
+ /* Route path for each internal PIRQx in PIC mode */
+ uint8_t pic[NUM_PIRQS];
+};
+
+static struct baytrail_irq_route irq_info = {
+ {
+ PCI_DEV_PIRQ_ROUTE(0x02, A, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x10, D, E, F, G),
+ PCI_DEV_PIRQ_ROUTE(0x11, B, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x12, C, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x13, D, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x14, E, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x15, F, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x17, F, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x18, B, A, D, C),
+ PCI_DEV_PIRQ_ROUTE(0x1a, F, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x1b, G, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x1c, E, F, G, H),
+ PCI_DEV_PIRQ_ROUTE(0x1d, D, A, A, A),
+ PCI_DEV_PIRQ_ROUTE(0x1e, B, D, E, F),
+ PCI_DEV_PIRQ_ROUTE(0x1f, H, G, B, C),
+ }, {
+ /*
+ * Route each PIRQ[A-H] to a PIC IRQ[0-15]
+ * Reserved: 0, 1, 2, 8, 13
+ * PS2 keyboard: 12
+ * ACPI/SCI: 9
+ * Floppy: 6
+ */
+ PIRQ_PIC(A, 4),
+ PIRQ_PIC(B, 5),
+ PIRQ_PIC(C, 7),
+ PIRQ_PIC(D, 10),
+ PIRQ_PIC(E, 11),
+ PIRQ_PIC(F, 12),
+ PIRQ_PIC(G, 14),
+ PIRQ_PIC(H, 15),
+ }
+};
+
+struct ibase_regs {
+ u32 actl;
+ u32 mc;
+ u8 pirq[8];
+ u32 scnt; /* 0x10 */
+ u32 kmc;
+ u32 fs;
+ u32 bc;
+ u16 ir[32]; /* 0x20 */
+ u32 oic; /* 0x60 */
+};
+
+enum {
+ /* ACTL */
+ SCIS_MASK = 0x07,
+ SCIS_IRQ9 = 0,
+ SCIS_IRQ10,
+ SCIS_IRQ11,
+ SCIS_IRQ20,
+ SCIS_IRQ21,
+ SCIS_IRQ22,
+ SCIS_IRQ23,
+
+ /* OIC */
+ AEN = 1 << 8,
+
+ /* SCNT */
+ SCNT_CONTINUOUS_MODE = 1 << 7,
+ SCNT_QUIET_MODE = 0,
+ SIRQEN = 1 << 12,
+
+ IBASE = 0x50,
+};
+
+static int valleyview_enable_ioapic(struct udevice *dev,
+ struct ibase_regs *ibase)
+{
+ u32 reg32;
+ int i;
+
+ /* Enable ACPI I/O and power management. Set SCI IRQ to IRQ9 */
+ writel(AEN, &ibase->oic);
+ reg32 = readl(&ibase->oic); /* Read back per BWG */
+ writel(SCIS_IRQ9, &ibase->actl);
+
+ io_apic_write(0, 1 << 25);
+
+ /* affirm full set of redirection table entries ("write once") */
+ reg32 = io_apic_read(1);
+ io_apic_write(1, reg32);
+
+ reg32 = io_apic_read(0);
+ debug("Southbridge APIC ID = %x\n", (reg32 >> 24) & 0x0f);
+ if (reg32 != (1 << 25)) {
+ debug("APIC Error\n");
+ return -EINVAL;
+ }
+
+ debug("Dumping IOAPIC registers\n");
+ for (i = 0; i < 3; i++)
+ debug(" reg 0x%04x: 0x%08x\n", i, io_apic_read(i));
+
+ /*
+ * 3 = Select Boot Configuration register
+ * 1 = Use Processor System Bus to deliver interrupts
+ */
+ io_apic_write(3, 1);
+
+ return 0;
+}
+
+static void valleyview_enable_serial_irqs(struct udevice *dev,
+ struct ibase_regs *ibase)
+{
+#ifdef SETUPSERIQ /* NOT defined. Remove when the TODO is done */
+ /*
+ * TODO: SERIRQ seems to have a number of problems on baytrail.
+ * With it enabled, we get some spurious interrupts (ps2)
+ * in seabios. It also caused IOCHK# NMIs. Remove it
+ * until we understand how it needs to be configured.
+ */
+ u8 reg;
+
+ /* Disable the IOCHK# NMI. Let the NMI handler enable it if needed */
+ reg = inb(0x61);
+ reg &= 0x0f; /* Higher Nibble must be 0 */
+ reg |= 1 << 3; /* IOCHK# NMI Disable for now */
+ outb(reg, 0x61);
+
+ setbits_le32(&ibase->oic, SIRQEN);
+ writeb(SCNT_CONTINUOUS_MODE, &ibase->scnt);
+
+#if !IS_ENABLED(CONFIG_SERIRQ_CONTINUOUS_MODE)
+ /*
+ * SoC requires that the System BIOS first set the SERIRQ logic to
+ * continuous mode operation for at least one frame before switching
+ * it into quiet mode operation.
+ */
+ outb(0x00, 0xed); /* I/O Delay to get the 1 frame */
+ writeb(SCNT_QUIET_MODE, &ibase->scnt);
+#endif
+#endif /* DON'T SET UP IRQS */
+}
+
+/**
+ * Take an INT_PIN number (0, 1 - 4) and convert
+ * it to a string ("NO PIN", "PIN A" - "PIN D")
+ *
+ * @param pin PCI Interrupt Pin number (0, 1 - 4)
+ * @return A string corresponding to the pin number or "Invalid"
+ */
+static const char *pin_to_str(int pin)
+{
+ const char *str[5] = {
+ "NO PIN",
+ "PIN A",
+ "PIN B",
+ "PIN C",
+ "PIN D",
+ };
+
+ if (pin >= 0 && pin <= 4)
+ return str[pin];
+ else
+ return "Invalid PIN, not 0 - 4";
+}
+
+/**
+ * Get the PCI INT_PIN swizzle for a device defined as:
+ * pin_parent = (pin_child + devn_child) % 4 + 1
+ * where PIN A = 1 ... PIN_D = 4
+ *
+ * Given a PCI device structure 'dev', find the interrupt pin
+ * that will be triggered on its parent bridge device when
+ * generating an interrupt. For example: Device 1:3.2 may
+ * use INT_PIN A but will trigger PIN D on its parent bridge
+ * device. In this case, this function will return 4 (PIN D).
+ *
+ * @param dev A PCI device structure to swizzle interrupt pins for
+ * @param *parent_bridge The PCI device structure for the bridge
+ * device 'dev' is attached to
+ * @return The interrupt pin number (1 - 4) that 'dev' will
+ * trigger when generating an interrupt
+ */
+static int swizzle_irq_pins(struct udevice *dev,
+ struct udevice **parent_bridgep)
+{
+ struct udevice *parent; /* Our current device's parent device */
+ struct udevice *child; /* The child device of the parent */
+ uint8_t swizzled_pin = 0; /* Pin swizzled across a bridge */
+
+ /* Start with PIN A = 0 ... D = 3 */
+ dm_pci_read_config8(dev, PCI_INTERRUPT_PIN, &swizzled_pin);
+ swizzled_pin -= 1;
+
+ /* While our current device has parent devices */
+ child = dev;
+ for (parent = child->parent; parent; parent = parent->parent) {
+ struct pci_child_platdata *pplat, *cplat;
+
+ cplat = dev_get_parent_platdata(child);
+ pplat = dev_get_parent_platdata(parent);
+
+ /* Swizzle the INT_PIN for any bridges not on root bus */
+ swizzled_pin = (PCI_DEV(cplat->devfn) + swizzled_pin) % 4;
+ debug("\tWith INT_PIN swizzled to %s\n"
+ "\tAttached to bridge device %01X:%02Xh.%02Xh\n",
+ pin_to_str(swizzled_pin + 1), parent->seq,
+ PCI_DEV(pplat->devfn), PCI_FUNC(pplat->devfn));
+
+ /* Continue until we find the root bus */
+ if (device_get_uclass_id(parent->parent->parent) ==
+ UCLASS_PCI) {
+ /*
+ * We will go on to the next parent so this parent
+ * becomes the child
+ */
+ child = parent;
+ continue;
+ } else {
+ /*
+ * Found the root bridge device,
+ * fill in the structure and exit
+ */
+ *parent_bridgep = parent;
+ break;
+ }
+ }
+
+ /* End with PIN A = 1 ... D = 4 */
+ return swizzled_pin + 1;
+}
+
+/**
+ * get_pci_irq_pins() - Get interrupt pin number for a device
+ *
+ * Given a device structure 'dev', find its interrupt pin and its parent bridge
+ * 'parent_bdg' device structure. If it is behind a bridge, it will return the
+ * interrupt pin number (1 - 4) of the parent bridge that the device interrupt
+ * pin has been swizzled to, otherwise it will return the interrupt pin that is
+ * programmed into the PCI config space of the target device. If 'dev' is
+ * behind a bridge, it will fill in 'parent_bdg' with the device structure of
+ * the bridge it is behind, otherwise it will copy 'dev' into 'parent_bdg'.
+ *
+ * @param dev Device to check
+ * @param *parent_bdgp Parent bridge for device
+ * @return interrupt pin number (1 - 4) that @dev will trigger when
+ * generating an interrupt, or -EINVAL is the pin is invalid, or
+ * -ENOENT if there was no paremt bridge
+ */
+static int get_pci_irq_pins(struct udevice *dev, struct udevice **parent_bdgp)
+{
+ uint8_t bus = 0; /* The bus this device is on */
+ uint16_t devfn = 0; /* This device's device and function numbers */
+ uint8_t int_pin = 0; /* Interrupt pin used by the device */
+ uint8_t target_pin = 0; /* Interrupt pin we want to assign an IRQ to */
+
+ bus = dev->parent->seq;
+ devfn = pci_get_bdf(dev);
+
+ /* Get and validate the interrupt pin used. Only 1-4 are allowed */
+ dm_pci_read_config8(dev, PCI_INTERRUPT_PIN, &int_pin);
+ if (int_pin < 1 || int_pin > 4)
+ return -EINVAL;
+
+ debug("PCI IRQ: Found device %01X:%02X.%02X using %s\n", bus,
+ PCI_DEV(devfn), PCI_FUNC(devfn), pin_to_str(int_pin));
+
+ /* If this device is on a bridge, swizzle its INT_PIN */
+ if (bus) {
+ /* Swizzle its INT_PINs */
+ target_pin = swizzle_irq_pins(dev, parent_bdgp);
+
+ /* Make sure the swizzle returned valid structures */
+ if (*parent_bdgp == NULL) {
+ debug("Warning: Could not find parent bridge for this
device!\n");
+ return -ENOENT;
+ }
+ } else { /* Device is not behind a bridge */
+ target_pin = int_pin; /* Return its own interrupt pin */
+ *parent_bdgp = dev; /* Return its own structure */
+ }
+
+ /* Target pin is the interrupt pin we want to assign an IRQ to */
+ return target_pin;
+}
+
+/*
+ * Write PCI config space IRQ assignments. PCI devices have the INT_LINE
+ * (0x3C) and INT_PIN (0x3D) registers which report interrupt routing
+ * information to operating systems and drivers. The INT_PIN register is
+ * generally read only and reports which interrupt pin A - D it uses. The
+ * INT_LINE register is configurable and reports which IRQ (generally the
+ * PIC IRQs 1 - 15) it will use. This needs to take interrupt pin swizzling
+ * on devices that are downstream on a PCI bridge into account.
+ *
+ * This function will loop through all enabled PCI devices and program the
+ * INT_LINE register with the correct PIC IRQ number for the INT_PIN that it
+ * uses. It then configures each interrupt in the pic to be level triggered.
+ */
+static void write_pci_config_irqs(const struct baytrail_irq_route *ir)
+{
+ struct udevice *dev;
+
+ for (pci_find_first_device(&dev); dev; pci_find_next_device(&dev)) {
+ pci_dev_t current_bdf = pci_get_bdf(dev);
+ struct udevice *targ_dev;
+ uint8_t original_int_pin;
+ pci_dev_t parent_bdf;
+ uint8_t new_int_pin;
+ uint8_t device_num;
+ uint8_t pirq;
+ uint8_t int_line;
+
+ /* Get the INT_PIN and device structure to look for */
+ targ_dev = NULL;
+ new_int_pin = get_pci_irq_pins(dev, &targ_dev);
+ if (targ_dev == NULL || new_int_pin < 1)
+ continue;
+
+ /* Get the original INT_PIN for record keeping */
+ dm_pci_read_config8(dev, PCI_INTERRUPT_PIN, &original_int_pin);
+
+ parent_bdf = pci_get_bdf(targ_dev);
+ device_num = PCI_DEV(parent_bdf);
+
+ if (ir->pcidev[device_num] == 0) {
+ debug("Warning: PCI Device %d does not have an IRQ
entry, skipping it\n",
+ device_num);
+ continue;
+ }
+
+ /*
+ * Find the PIRQ that is attached to the INT_PIN this device
+ * uses.
+ * TODO(sjg): Rationalise this with pirq_route_irqs() and
+ * pci_assign_irqs().
+ */
+ pirq = (ir->pcidev[device_num] >> ((new_int_pin - 1) * 4)) &
+ 0xf;
+
+ /* Get the INT_LINE this device/function will use */
+ int_line = ir->pic[pirq];
+
+ if (int_line != PIRQ_PIC_IRQDISABLE) {
+ /*
+ * Set this IRQ to level triggered since it is used by
+ * a PCI device
+ */
+ configure_irq_trigger(int_line, true);
+ dm_pci_write_config8(dev, PCI_INTERRUPT_LINE, int_line);
+ } else {
+ dm_pci_write_config8(dev, PCI_INTERRUPT_LINE,
+ PCI_INTERRUPT_LINE_DISABLE);
+ }
+
+ debug("\tINT_PIN\t\t: %d (%s)\n",
+ original_int_pin, pin_to_str(original_int_pin));
+ if (parent_bdf != current_bdf) {
+ debug("\tSwizzled to\t: %d (%s)\n", new_int_pin,
+ pin_to_str(new_int_pin));
+ }
+ debug("\tPIRQ\t\t: %c\n", 'A' + pirq);
+ debug("\tINT_LINE\t: 0x%X (IRQ %d)\n", int_line, int_line);
+ }
+}
+
+static void valleyview_pirq_init(const struct baytrail_irq_route *ir,
+ struct ibase_regs *ibase)
+{
+ int i;
+
+ /* Set up the PIRQ PIC routing based on static config */
+ debug("Start writing IRQ assignments\n"
+ "PIRQ\tA \tB \tC \tD \tE \tF \tG \tH\n"
+ "IRQ ");
+ for (i = 0; i < NUM_PIRQS; i++) {
+ writeb(ir->pic[i], &ibase->pirq[i]);
+ debug("\t%d", ir->pic[i]);
+ }
+ debug("\n\n");
+
+ /* Set up the per device PIRQ routing based on static config */
+ debug("\t\t\tPIRQ[A-H] routed to each INT_PIN[A-D]\n"
+ "Dev\tINTA (IRQ)\tINTB (IRQ)\tINTC (IRQ)\tINTD (IRQ)\n");
+
+ for (i = 0; i < NUM_OF_PCI_DEVS; i++) {
+ writew(ir->pcidev[i], &ibase->ir[i]);
+
+ /* If the entry is more than just 0, print it out */
+ if (ir->pcidev[i]) {
+ int j, pirq;
+
+ debug(" %d: ", i);
+ for (j = 0; j < 4; j++) {
+ pirq = (ir->pcidev[i] >> (j * 4)) & 0xF;
+ debug("\t%-4c (%d)", 'A' + pirq, ir->pic[pirq]);
+ }
+ debug("\n");
+ }
+ }
+
+ /* Write IRQ assignments to PCI config space */
+ write_pci_config_irqs(ir);
+}
+
+static int valleyview_init(struct udevice *dev)
+{
+ int ret;
+ u32 addr;
+ struct ibase_regs *ibase;
+
+ debug("%s\n", __func__);
+
+ dm_pci_read_config32(dev, IBASE, &addr);
+ addr &= ~0xf;
+ ibase = (struct ibase_regs *)addr;
+ debug("ibase = %p\n", ibase);
+
+ writeb(0, &ibase->mc);
+
+ /* Enable special cycles */
+ dm_pci_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_SPECIAL);
+
+ /* IO APIC initialisation */
+ ret = valleyview_enable_ioapic(dev, ibase);
+ if (ret)
+ return ret;
+
+ valleyview_enable_serial_irqs(dev, ibase);
+
+ /* Setup the PIRQ */
+ valleyview_pirq_init(&irq_info, ibase);
+
+ return fsp_init_phase_pci();
+}
+
+int arch_misc_init(void)
+{
+ struct udevice *dev;
+ int ret;
+
+ ret = pci_bus_find_bdf(PCI_BDF(0, 0x1f, 0), &dev);
+ if (ret) {
+ debug("Cannot find Intel Legacy Block\n");
+ return ret;
+ }
+
+ return valleyview_init(dev);
+}
diff --git a/arch/x86/dts/minnowmax.dts b/arch/x86/dts/minnowmax.dts
index 9527233..fb2510b 100644
--- a/arch/x86/dts/minnowmax.dts
+++ b/arch/x86/dts/minnowmax.dts
@@ -7,6 +7,7 @@
/dts-v1/;
#include <dt-bindings/gpio/x86-gpio.h>
+#include <dt-bindings/interrupt-router/intel-irq.h>
/include/ "skeleton.dtsi"
/include/ "serial.dtsi"
@@ -120,6 +121,33 @@
ranges = <0x02000000 0x0 0xd0000000 0xd0000000 0 0x10000000
0x42000000 0x0 0xc0000000 0xc0000000 0 0x10000000
0x01000000 0x0 0x2000 0x2000 0 0xe000>;
+
+ /* TODO(s...@chromium.org): Currently unused */
+ irq-router@1f,0 {
+ reg = <0x0000f800 0 0 0 0>;
+ compatible = "intel,irq-router";
+ intel,pirq-config = "ibase";
+ intel,ibase-offset = <0x50>;
+ intel,pirq-link = <0x20 32>;
+ intel,pirq-mask = <0xdcb0>;
+ intel,pirq-routing = <
+ PCI_BDF(0, 0x02, 0) INTB PIRQA
+ PCI_BDF(0, 0x10, 0) INTA PIRQD
+ PCI_BDF(0, 0x11, 0) INTA PIRQB
+ PCI_BDF(0, 0x12, 0) INTA PIRQC
+ PCI_BDF(0, 0x13, 0) INTA PIRQD
+ PCI_BDF(0, 0x14, 0) INTA PIRQE
+ PCI_BDF(0, 0x15, 0) INTC PIRQF
+ PCI_BDF(0, 0x17, 0) INTA PIRQF
+ PCI_BDF(0, 0x18, 0) INTA PIRQB
+ PCI_BDF(0, 0x1a, 0) INTA PIRQF
+ PCI_BDF(0, 0x1b, 0) INTA PIRQG
+ PCI_BDF(0, 0x1c, 0) INTD PIRQE
+ PCI_BDF(0, 0x1d, 0) INTA PIRQD
+ PCI_BDF(0, 0x1e, 0) INTB PIRQB
+ PCI_BDF(0, 0x1f, 0) INTC PIRQH
+ >;
+ };
};
spi {
diff --git a/include/configs/minnowmax.h b/include/configs/minnowmax.h
index cdbb65d..ffa5510 100644
--- a/include/configs/minnowmax.h
+++ b/include/configs/minnowmax.h
@@ -16,6 +16,7 @@
#define CONFIG_SYS_MONITOR_LEN (1 << 20)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_ARCH_EARLY_INIT_R
+#define CONFIG_ARCH_MISC_INIT
#define CONFIG_SMSC_LPC47M
--
2.5.0.rc2.392.g76e840b
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
