From: Sylvain Lemieux <slemi...@tycoint.com> Incorporate ECC layout for small page NAND from legacy LPCLinux NXP BSP. The code taken from the legacy patch is: - lpc32xx SLC NAND driver (ECC layout for small page)
This layout is matching the lpc32xx NAND SLC Kernel driver: https://git.kernel.org/cgit/linux/kernel/git/stable/linux-stable.git/tree/drivers/mtd/nand/lpc32xx_slc.c?id=refs/tags/v4.1.3 Signed-off-by: Sylvain Lemieux <slemi...@tycoint.com> --- Changes from v5 to v6: * Updated comment regarding default OOB layout. Changes from v4 to v5: * No changes; patch context updated. Changes from v3 to v4: * No changes. Changes from v2 to v3: * No changes; patch context updated. Changes from v1 to v2: * Move ECC layout for small page NAND into a separate patch. The legacy BSP patch (u-boot-2009.03_lpc32x0-v1.07.patch.tar.bz2) was downloaded from the LPCLinux Web site. drivers/mtd/nand/lpc32xx_nand_slc.c | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) diff --git a/drivers/mtd/nand/lpc32xx_nand_slc.c b/drivers/mtd/nand/lpc32xx_nand_slc.c index 2a32264..088818f 100644 --- a/drivers/mtd/nand/lpc32xx_nand_slc.c +++ b/drivers/mtd/nand/lpc32xx_nand_slc.c @@ -94,6 +94,19 @@ struct lpc32xx_nand_slc_regs { #define TAC_R_HOLD(n) (max_t(uint32_t, (n), 0xF) << 4) #define TAC_R_SETUP(n) (max_t(uint32_t, (n), 0xF) << 0) +/* NAND ECC Layout for small page NAND devices + * Note: For large page devices, the default layouts are used. */ +static struct nand_ecclayout lpc32xx_nand_oob_16 = { + .eccbytes = 6, + .eccpos = {10, 11, 12, 13, 14, 15}, + .oobfree = { + {.offset = 0, + . length = 4}, + {.offset = 6, + . length = 4} + } +}; + #if defined(CONFIG_DMA_LPC32XX) /* Total ECC bytes and size; refer to board_nand_init() for details. */ #define ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE) @@ -530,7 +543,7 @@ int board_nand_init(struct nand_chip *lpc32xx_chip) lpc32xx_chip->write_buf = lpc32xx_write_buf; /* - * Use default ECC layout, but these values are predefined + * These values are predefined * for both small and large page NAND flash devices. */ lpc32xx_chip->ecc.size = CONFIG_SYS_NAND_ECCSIZE; @@ -539,6 +552,9 @@ int board_nand_init(struct nand_chip *lpc32xx_chip) lpc32xx_chip->ecc.strength = 1; + if (CONFIG_SYS_NAND_PAGE_SIZE != NAND_LARGE_BLOCK_PAGE_SIZE) + lpc32xx_chip->ecc.layout = &lpc32xx_nand_oob_16; + #if defined(CONFIG_SYS_NAND_USE_FLASH_BBT) lpc32xx_chip->bbt_options |= NAND_BBT_USE_FLASH; #endif -- 1.8.3.1 _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
