LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivast...@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabha...@freescale.com>
---
Changes for v2: Rebased on LS1043 patch set
README | 3 +
arch/arm/Kconfig | 44 +++++++----
arch/arm/cpu/armv8/fsl-layerscape/Makefile | 4 +-
arch/arm/cpu/armv8/fsl-layerscape/README.lsch3 | 4 +-
arch/arm/cpu/armv8/fsl-layerscape/cpu.c | 2 +-
arch/arm/cpu/armv8/fsl-layerscape/fdt.c | 2 +-
.../arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c | 11 +++
.../{ls2085a_serdes.c => ls2080a_serdes.c} | 0
arch/arm/cpu/armv8/fsl-layerscape/soc.c | 2 +-
arch/arm/cpu/armv8/fsl-layerscape/spl.c | 4 +-
arch/arm/dts/Makefile | 4 +-
.../{fsl-ls2085a-qds.dts => fsl-ls2080a-qds.dts} | 8 +-
.../{fsl-ls2085a-rdb.dts => fsl-ls2080a-rdb.dts} | 8 +-
.../arm/dts/{fsl-ls2085a.dtsi => fsl-ls2080a.dtsi} | 4 +-
arch/arm/include/asm/arch-fsl-layerscape/config.h | 4 +-
arch/arm/include/asm/arch-fsl-layerscape/cpu.h | 6 +-
.../include/asm/arch-fsl-layerscape/fsl_serdes.h | 2 +-
.../include/asm/arch-fsl-layerscape/immap_lsch3.h | 6 +-
.../{ls2085a_stream_id.h => ls2080a_stream_id.h} | 4 +-
arch/arm/include/asm/global_data.h | 2 +-
board/freescale/{ls2085a => ls2080a}/Kconfig | 12 +--
board/freescale/ls2080a/MAINTAINERS | 8 ++
board/freescale/ls2080a/Makefile | 8 ++
board/freescale/{ls2085a => ls2080a}/README | 2 +-
board/freescale/{ls2085a => ls2080a}/ddr.c | 3 +-
board/freescale/{ls2085a => ls2080a}/ddr.h | 0
.../{ls2085a/ls2085a.c => ls2080a/ls2080a.c} | 2 +
board/freescale/{ls2085ardb => ls2080aqds}/Kconfig | 6 +-
board/freescale/ls2080aqds/MAINTAINERS | 8 ++
.../freescale/{ls2085aqds => ls2080aqds}/Makefile | 2 +-
board/freescale/{ls2085aqds => ls2080aqds}/README | 16 ++--
board/freescale/{ls2085ardb => ls2080aqds}/ddr.c | 5 +-
board/freescale/{ls2085aqds => ls2080aqds}/ddr.h | 0
board/freescale/{ls2085aqds => ls2080aqds}/eth.c | 92 +++++++++++-----------
.../ls2085aqds.c => ls2080aqds/ls2080aqds.c} | 4 +-
.../ls2080aqds_qixis.h} | 0
board/freescale/{ls2085aqds => ls2080ardb}/Kconfig | 6 +-
board/freescale/ls2080ardb/MAINTAINERS | 8 ++
.../freescale/{ls2085ardb => ls2080ardb}/Makefile | 2 +-
board/freescale/{ls2085ardb => ls2080ardb}/README | 12 +--
board/freescale/{ls2085aqds => ls2080ardb}/ddr.c | 5 +-
board/freescale/{ls2085ardb => ls2080ardb}/ddr.h | 0
.../eth_ls2085rdb.c => ls2080ardb/eth_ls2080rdb.c} | 2 +-
.../ls2085ardb.c => ls2080ardb/ls2080ardb.c} | 4 +-
.../ls2080ardb_qixis.h} | 0
board/freescale/ls2085a/MAINTAINERS | 8 --
board/freescale/ls2085a/Makefile | 8 --
board/freescale/ls2085aqds/MAINTAINERS | 8 --
board/freescale/ls2085ardb/MAINTAINERS | 8 --
...ls2085a_emu_defconfig => ls2080a_emu_defconfig} | 2 +-
...2085a_simu_defconfig => ls2080a_simu_defconfig} | 2 +-
.../{ls2085ardb_defconfig => ls2080aqds_defconfig} | 4 +-
...ds_nand_defconfig => ls2080aqds_nand_defconfig} | 2 +-
.../{ls2085aqds_defconfig => ls2080ardb_defconfig} | 4 +-
...db_nand_defconfig => ls2080ardb_nand_defconfig} | 2 +-
doc/README.fsl-trustzone-components | 4 +-
drivers/ddr/fsl/fsl_ddr_gen4.c | 4 +-
drivers/net/fsl-mc/mc.c | 5 +-
drivers/net/ldpaa_eth/Makefile | 2 +-
drivers/net/ldpaa_eth/{ls2085a.c => ls2080a.c} | 0
drivers/pci/pcie_layerscape.c | 2 +-
.../configs/{ls2085a_common.h => ls2080a_common.h} | 10 ++-
include/configs/{ls2085a_emu.h => ls2080a_emu.h} | 8 +-
include/configs/{ls2085a_simu.h => ls2080a_simu.h} | 8 +-
include/configs/{ls2085aqds.h => ls2080aqds.h} | 4 +-
include/configs/{ls2085ardb.h => ls2080ardb.h} | 4 +-
include/linux/usb/xhci-fsl.h | 6 +-
67 files changed, 246 insertions(+), 190 deletions(-)
rename arch/arm/cpu/armv8/fsl-layerscape/{ls2085a_serdes.c =>
ls2080a_serdes.c} (100%)
rename arch/arm/dts/{fsl-ls2085a-qds.dts => fsl-ls2080a-qds.dts} (80%)
rename arch/arm/dts/{fsl-ls2085a-rdb.dts => fsl-ls2080a-rdb.dts} (67%)
rename arch/arm/dts/{fsl-ls2085a.dtsi => fsl-ls2080a.dtsi} (97%)
rename arch/arm/include/asm/arch-fsl-layerscape/{ls2085a_stream_id.h =>
ls2080a_stream_id.h} (93%)
rename board/freescale/{ls2085a => ls2080a}/Kconfig (66%)
create mode 100644 board/freescale/ls2080a/MAINTAINERS
create mode 100644 board/freescale/ls2080a/Makefile
rename board/freescale/{ls2085a => ls2080a}/README (97%)
rename board/freescale/{ls2085a => ls2080a}/ddr.c (99%)
rename board/freescale/{ls2085a => ls2080a}/ddr.h (100%)
rename board/freescale/{ls2085a/ls2085a.c => ls2080a/ls2080a.c} (98%)
rename board/freescale/{ls2085ardb => ls2080aqds}/Kconfig (67%)
create mode 100644 board/freescale/ls2080aqds/MAINTAINERS
rename board/freescale/{ls2085aqds => ls2080aqds}/Makefile (83%)
rename board/freescale/{ls2085aqds => ls2080aqds}/README (95%)
rename board/freescale/{ls2085ardb => ls2080aqds}/ddr.c (98%)
rename board/freescale/{ls2085aqds => ls2080aqds}/ddr.h (100%)
rename board/freescale/{ls2085aqds => ls2080aqds}/eth.c (88%)
rename board/freescale/{ls2085aqds/ls2085aqds.c => ls2080aqds/ls2080aqds.c}
(98%)
rename board/freescale/{ls2085aqds/ls2085aqds_qixis.h =>
ls2080aqds/ls2080aqds_qixis.h} (100%)
rename board/freescale/{ls2085aqds => ls2080ardb}/Kconfig (67%)
create mode 100644 board/freescale/ls2080ardb/MAINTAINERS
rename board/freescale/{ls2085ardb => ls2080ardb}/Makefile (72%)
rename board/freescale/{ls2085ardb => ls2080ardb}/README (94%)
rename board/freescale/{ls2085aqds => ls2080ardb}/ddr.c (98%)
rename board/freescale/{ls2085ardb => ls2080ardb}/ddr.h (100%)
rename board/freescale/{ls2085ardb/eth_ls2085rdb.c =>
ls2080ardb/eth_ls2080rdb.c} (98%)
rename board/freescale/{ls2085ardb/ls2085ardb.c => ls2080ardb/ls2080ardb.c}
(98%)
rename board/freescale/{ls2085ardb/ls2085ardb_qixis.h =>
ls2080ardb/ls2080ardb_qixis.h} (100%)
delete mode 100644 board/freescale/ls2085a/MAINTAINERS
delete mode 100644 board/freescale/ls2085a/Makefile
delete mode 100644 board/freescale/ls2085aqds/MAINTAINERS
delete mode 100644 board/freescale/ls2085ardb/MAINTAINERS
rename configs/{ls2085a_emu_defconfig => ls2080a_emu_defconfig} (93%)
rename configs/{ls2085a_simu_defconfig => ls2080a_simu_defconfig} (93%)
rename configs/{ls2085ardb_defconfig => ls2080aqds_defconfig} (78%)
rename configs/{ls2085aqds_nand_defconfig => ls2080aqds_nand_defconfig} (86%)
rename configs/{ls2085aqds_defconfig => ls2080ardb_defconfig} (78%)
rename configs/{ls2085ardb_nand_defconfig => ls2080ardb_nand_defconfig} (86%)
rename drivers/net/ldpaa_eth/{ls2085a.c => ls2080a.c} (100%)
rename include/configs/{ls2085a_common.h => ls2080a_common.h} (98%)
rename include/configs/{ls2085a_emu.h => ls2080a_emu.h} (94%)
rename include/configs/{ls2085a_simu.h => ls2080a_simu.h} (96%)
rename include/configs/{ls2085aqds.h => ls2080aqds.h} (99%)
rename include/configs/{ls2085ardb.h => ls2080ardb.h} (99%)
diff --git a/README b/README
index d18df54..28f1366 100644
--- a/README
+++ b/README
@@ -611,6 +611,9 @@ The following options need to be configured:
CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
Number of controllers used for other than main memory.
+ CONFIG_SYS_FSL_HAS_DP_DDR
+ Defines the SoC has DP-DDR used for DPAA.
+
CONFIG_SYS_FSL_SEC_BE
Defines the SEC controller register space as Big Endian
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 3992f69..20eb94f 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -576,36 +576,46 @@ config TARGET_VEXPRESS64_JUNO
bool "Support Versatile Express Juno Development Platform"
select ARM64
-config TARGET_LS2085A_EMU
- bool "Support ls2085a_emu"
+config TARGET_LS2080A_EMU
+ bool "Support ls2080a_emu"
select ARM64
select ARMV8_MULTIENTRY
+ help
+ Support for Freescale LS2080A_EMU platform
+ The LS2080A Development System (EMULATOR) is a pre silicon
+ development platform that supports the QorIQ LS2080A
+ Layerscape Architecture processor.
-config TARGET_LS2085A_SIMU
- bool "Support ls2085a_simu"
+config TARGET_LS2080A_SIMU
+ bool "Support ls2080a_simu"
select ARM64
select ARMV8_MULTIENTRY
+ help
+ Support for Freescale LS2080A_SIMU platform
+ The LS2080A Development System (QDS) is a pre silicon
+ development platform that supports the QorIQ LS2080A
+ Layerscape Architecture processor.
-config TARGET_LS2085AQDS
- bool "Support ls2085aqds"
+config TARGET_LS2080AQDS
+ bool "Support ls2080aqds"
select ARM64
select ARMV8_MULTIENTRY
select SUPPORT_SPL
help
- Support for Freescale LS2085AQDS platform
- The LS2085A Development System (QDS) is a high-performance
- development platform that supports the QorIQ LS2085A
+ Support for Freescale LS2080AQDS platform
+ The LS2080A Development System (QDS) is a high-performance
+ development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.
-config TARGET_LS2085ARDB
- bool "Support ls2085ardb"
+config TARGET_LS2080ARDB
+ bool "Support ls2080ardb"
select ARM64
select ARMV8_MULTIENTRY
select SUPPORT_SPL
help
- Support for Freescale LS2085ARDB platform.
- The LS2085A Reference design board (RDB) is a high-performance
- development platform that supports the QorIQ LS2085A
+ Support for Freescale LS2080ARDB platform.
+ The LS2080A Reference design board (RDB) is a high-performance
+ development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.
config TARGET_HIKEY
@@ -746,9 +756,9 @@ source "board/compulab/cm_t43/Kconfig"
source "board/creative/xfi3/Kconfig"
source "board/denx/m28evk/Kconfig"
source "board/denx/m53evk/Kconfig"
-source "board/freescale/ls2085a/Kconfig"
-source "board/freescale/ls2085aqds/Kconfig"
-source "board/freescale/ls2085ardb/Kconfig"
+source "board/freescale/ls2080a/Kconfig"
+source "board/freescale/ls2080aqds/Kconfig"
+source "board/freescale/ls2080ardb/Kconfig"
source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
source "board/freescale/ls1043ardb/Kconfig"
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile
b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
index 6fa08c8..1beb426 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
@@ -21,8 +21,8 @@ obj-$(CONFIG_SYS_HAS_SERDES) += fsl_lsch2_serdes.o
endif
endif
-ifneq ($(CONFIG_LS2085A),)
-obj-$(CONFIG_SYS_HAS_SERDES) += ls2085a_serdes.o
+ifneq ($(CONFIG_LS2080A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls2080a_serdes.o
else
ifneq ($(CONFIG_LS1043A),)
obj-$(CONFIG_SYS_HAS_SERDES) += ls1043a_serdes.o
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/README.lsch3
b/arch/arm/cpu/armv8/fsl-layerscape/README.lsch3
index 1b7e698..b924134 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/README.lsch3
+++ b/arch/arm/cpu/armv8/fsl-layerscape/README.lsch3
@@ -7,7 +7,7 @@
Freescale LayerScape with Chassis Generation 3
This architecture supports Freescale ARMv8 SoCs with Chassis generation 3,
-for example LS2085A.
+for example LS2080A.
DDR Layout
============
@@ -152,7 +152,7 @@ u-boot command
nand write <rcw image in memory> 0 <size of rcw image>
To form the NAND image, build u-boot with NAND config, for example,
-ls2085aqds_nand_defconfig. The image needed is u-boot-with-spl.bin.
+ls2080aqds_nand_defconfig. The image needed is u-boot-with-spl.bin.
The u-boot image should be written to match SRC_ADDR, in above example 0x20000.
nand write <u-boot image in memory> 200000 <size of u-boot image>
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
index dbb12c2..f13c2fc 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
@@ -438,7 +438,7 @@ int print_cpuinfo(void)
#ifdef CONFIG_SYS_DPAA_FMAN
printf(" FMAN: %-4s MHz", strmhz(buf, sysinfo.freq_fman[0]));
#endif
-#ifdef CONFIG_FSL_LSCH3
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
printf(" DP-DDR: %-4s MT/s", strmhz(buf, sysinfo.freq_ddrbus2));
#endif
puts("\n");
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fdt.c
b/arch/arm/cpu/armv8/fsl-layerscape/fdt.c
index 47599c1..eafdd71 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/fdt.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/fdt.c
@@ -141,7 +141,7 @@ void append_mmu_masters(void *blob, const char *smmu_path,
/*
* The info below summarizes how streamID partitioning works
- * for ls2085a and how it is conveyed to the OS via the device tree.
+ * for ls2080a and how it is conveyed to the OS via the device tree.
*
* -non-PCI legacy, platform devices (USB, SD/MMC, SATA, DMA)
* -all legacy devices get a unique ICID assigned and programmed in
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c
b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c
index 4054c3c..81cf470 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/fsl_lsch3_speed.c
@@ -11,6 +11,7 @@
#include <fsl_ifc.h>
#include <asm/processor.h>
#include <asm/io.h>
+#include <asm/arch-fsl-layerscape/immap_lsch3.h>
#include <asm/arch/clock.h>
#include <asm/arch/soc.h>
#include "cpu.h"
@@ -77,11 +78,15 @@ void get_sys_info(struct sys_info *sys_info)
sys_info->freq_systembus = sysclk;
#ifdef CONFIG_DDR_CLK_FREQ
sys_info->freq_ddrbus = CONFIG_DDR_CLK_FREQ;
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
sys_info->freq_ddrbus2 = CONFIG_DDR_CLK_FREQ;
+#endif
#else
sys_info->freq_ddrbus = sysclk;
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
sys_info->freq_ddrbus2 = sysclk;
#endif
+#endif
sys_info->freq_systembus *= (gur_in32(&gur->rcwsr[0]) >>
FSL_CHASSIS3_RCWSR0_SYS_PLL_RAT_SHIFT) &
@@ -91,9 +96,11 @@ void get_sys_info(struct sys_info *sys_info)
sys_info->freq_ddrbus *= (gur_in32(&gur->rcwsr[0]) >>
FSL_CHASSIS3_RCWSR0_MEM_PLL_RAT_SHIFT) &
FSL_CHASSIS3_RCWSR0_MEM_PLL_RAT_MASK;
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
sys_info->freq_ddrbus2 *= (gur_in32(&gur->rcwsr[0]) >>
FSL_CHASSIS3_RCWSR0_MEM2_PLL_RAT_SHIFT) &
FSL_CHASSIS3_RCWSR0_MEM2_PLL_RAT_MASK;
+#endif
for (i = 0; i < CONFIG_SYS_FSL_NUM_CC_PLLS; i++) {
/*
@@ -133,7 +140,9 @@ int get_clocks(void)
gd->cpu_clk = sys_info.freq_processor[0];
gd->bus_clk = sys_info.freq_systembus;
gd->mem_clk = sys_info.freq_ddrbus;
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
gd->arch.mem2_clk = sys_info.freq_ddrbus2;
+#endif
#if defined(CONFIG_FSL_ESDHC)
gd->arch.sdhc_clk = gd->bus_clk / 2;
#endif /* defined(CONFIG_FSL_ESDHC) */
@@ -169,8 +178,10 @@ ulong get_ddr_freq(ulong ctrl_num)
* DDR controller 0 & 1 are on memory complex 0
* DDR controler 2 is on memory complext 1
*/
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (ctrl_num >= 2)
return gd->arch.mem2_clk;
+#endif
return gd->mem_clk;
}
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls2085a_serdes.c
b/arch/arm/cpu/armv8/fsl-layerscape/ls2080a_serdes.c
similarity index 100%
rename from arch/arm/cpu/armv8/fsl-layerscape/ls2085a_serdes.c
rename to arch/arm/cpu/armv8/fsl-layerscape/ls2080a_serdes.c
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/soc.c
b/arch/arm/cpu/armv8/fsl-layerscape/soc.c
index 34f9a94..54c75e2 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/soc.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/soc.c
@@ -13,7 +13,7 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
#ifdef CONFIG_SYS_FSL_ERRATUM_A009635
#define PLATFORM_CYCLE_ENV_VAR "a009635_interval_val"
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/spl.c
b/arch/arm/cpu/armv8/fsl-layerscape/spl.c
index ba551aa..a3410af 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/spl.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/spl.c
@@ -48,7 +48,7 @@ void board_init_f(ulong dummy)
gd = &gdata;
/* Clear global data */
memset((void *)gd, 0, sizeof(gd_t));
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
arch_cpu_init();
#endif
#ifdef CONFIG_FSL_IFC
@@ -56,7 +56,7 @@ void board_init_f(ulong dummy)
#endif
board_early_init_f();
timer_init();
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
env_init();
#endif
get_clocks();
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index ddc6a05..0a4405f 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -81,8 +81,8 @@ dtb-$(CONFIG_TARGET_STV0991) += stv0991.dtb
dtb-$(CONFIG_LS102XA) += ls1021a-qds.dtb \
ls1021a-twr.dtb
-dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2085a-qds.dtb \
- fsl-ls2085a-rdb.dtb
+dtb-$(CONFIG_FSL_LSCH3) += fsl-ls2080a-qds.dtb \
+ fsl-ls2080a-rdb.dtb
dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-a1000.dtb \
diff --git a/arch/arm/dts/fsl-ls2085a-qds.dts b/arch/arm/dts/fsl-ls2080a-qds.dts
similarity index 80%
rename from arch/arm/dts/fsl-ls2085a-qds.dts
rename to arch/arm/dts/fsl-ls2080a-qds.dts
index 4477e54..547ec27 100644
--- a/arch/arm/dts/fsl-ls2085a-qds.dts
+++ b/arch/arm/dts/fsl-ls2080a-qds.dts
@@ -1,5 +1,5 @@
/*
- * Freescale ls2085a QDS board device tree source
+ * Freescale ls2080a QDS board device tree source
*
* Copyright 2013-2015 Freescale Semiconductor, Inc.
*
@@ -8,11 +8,11 @@
/dts-v1/;
-#include "fsl-ls2085a.dtsi"
+#include "fsl-ls2080a.dtsi"
/ {
- model = "Freescale Layerscape 2085a QDS Board";
- compatible = "fsl,ls2085a-qds", "fsl,ls2085a";
+ model = "Freescale Layerscape 2080a QDS Board";
+ compatible = "fsl,ls2080a-qds", "fsl,ls2080a";
aliases {
spi1 = &dspi;
diff --git a/arch/arm/dts/fsl-ls2085a-rdb.dts b/arch/arm/dts/fsl-ls2080a-rdb.dts
similarity index 67%
rename from arch/arm/dts/fsl-ls2085a-rdb.dts
rename to arch/arm/dts/fsl-ls2080a-rdb.dts
index 25278df..1a1813b 100644
--- a/arch/arm/dts/fsl-ls2085a-rdb.dts
+++ b/arch/arm/dts/fsl-ls2080a-rdb.dts
@@ -1,5 +1,5 @@
/*
- * Freescale ls2085a RDB board device tree source
+ * Freescale ls2080a RDB board device tree source
*
* Copyright 2013-2015 Freescale Semiconductor, Inc.
*
@@ -8,11 +8,11 @@
/dts-v1/;
-#include "fsl-ls2085a.dtsi"
+#include "fsl-ls2080a.dtsi"
/ {
- model = "Freescale Layerscape 2085a RDB Board";
- compatible = "fsl,ls2085a-rdb", "fsl,ls2085a";
+ model = "Freescale Layerscape 2080a RDB Board";
+ compatible = "fsl,ls2080a-rdb", "fsl,ls2080a";
aliases {
spi1 = &dspi;
diff --git a/arch/arm/dts/fsl-ls2085a.dtsi b/arch/arm/dts/fsl-ls2080a.dtsi
similarity index 97%
rename from arch/arm/dts/fsl-ls2085a.dtsi
rename to arch/arm/dts/fsl-ls2080a.dtsi
index 96404c5..a5c579c 100644
--- a/arch/arm/dts/fsl-ls2085a.dtsi
+++ b/arch/arm/dts/fsl-ls2080a.dtsi
@@ -1,5 +1,5 @@
/*
- * Freescale ls2085a SOC common device tree source
+ * Freescale ls2080a SOC common device tree source
*
* Copyright 2013-2015 Freescale Semiconductor, Inc.
*
@@ -7,7 +7,7 @@
*/
/ {
- compatible = "fsl,ls2085a";
+ compatible = "fsl,ls2080a";
interrupt-parent = <&gic>;
#address-cells = <2>;
#size-cells = <2>;
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h
b/arch/arm/include/asm/arch-fsl-layerscape/config.h
index c7169ab..1b700b3 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/config.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h
@@ -17,10 +17,10 @@
#define CONFIG_SYS_FSL_DDR /* Freescale DDR driver */
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
-#if defined(CONFIG_LS2085A)
+#if defined(CONFIG_LS2080A)
#define CONFIG_MAX_CPUS 16
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
-#define CONFIG_NUM_DDR_CONTROLLERS 3
+#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1, 4, 4 }
#define SRDS_MAX_LANES 8
#define CONFIG_SYS_FSL_SRDS_1
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
index 2903996..5a91dcb 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/cpu.h
@@ -8,8 +8,10 @@
#define _FSL_LAYERSCAPE_CPU_H
static struct cpu_type cpu_type_list[] = {
- CPU_TYPE_ENTRY(LS2085, LS2085, 8),
+#ifdef CONFIG_LS2080A
CPU_TYPE_ENTRY(LS2080, LS2080, 8),
+#endif
+ CPU_TYPE_ENTRY(LS2085, LS2085, 8),
CPU_TYPE_ENTRY(LS2045, LS2045, 4),
CPU_TYPE_ENTRY(LS1043, LS1043, 4),
};
@@ -180,7 +182,7 @@ static const struct sys_mmu_table final_mmu_table[] = {
CONFIG_SYS_PCIE2_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
{ CONFIG_SYS_PCIE3_PHYS_ADDR, CONFIG_SYS_PCIE3_PHYS_ADDR,
CONFIG_SYS_PCIE3_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
{ CONFIG_SYS_PCIE4_PHYS_ADDR, CONFIG_SYS_PCIE4_PHYS_ADDR,
CONFIG_SYS_PCIE4_PHYS_SIZE, MT_DEVICE_NGNRNE, PMD_SECT_NON_SHARE },
#endif
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h
b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h
index e1043b5..4787eec 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/fsl_serdes.h
@@ -9,7 +9,7 @@
#include <config.h>
-#if defined(CONFIG_LS2085A)
+#if defined(CONFIG_LS2080A)
enum srds_prtcl {
NONE = 0,
PCIE1,
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index 6a70d44..134061c 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -51,8 +51,8 @@
#define I2C3_BASE_ADDR (CONFIG_SYS_IMMR + 0x01020000)
#define I2C4_BASE_ADDR (CONFIG_SYS_IMMR + 0x01030000)
-#define CONFIG_SYS_LS2085A_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000)
-#define CONFIG_SYS_LS2085A_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02110000)
+#define CONFIG_SYS_LS2080A_XHCI_USB1_ADDR (CONFIG_SYS_IMMR + 0x02100000)
+#define CONFIG_SYS_LS2080A_XHCI_USB2_ADDR (CONFIG_SYS_IMMR + 0x02110000)
/* TZ Address Space Controller Definitions */
#define TZASC1_BASE 0x01100000 /* as per CCSR map. */
@@ -115,7 +115,9 @@ struct sys_info {
unsigned long freq_processor[CONFIG_MAX_CPUS];
unsigned long freq_systembus;
unsigned long freq_ddrbus;
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
unsigned long freq_ddrbus2;
+#endif
unsigned long freq_localbus;
unsigned long freq_qe;
#ifdef CONFIG_SYS_DPAA_FMAN
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/ls2085a_stream_id.h
b/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
similarity index 93%
rename from arch/arm/include/asm/arch-fsl-layerscape/ls2085a_stream_id.h
rename to arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
index 5c94530..954104b 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/ls2085a_stream_id.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/ls2080a_stream_id.h
@@ -7,7 +7,7 @@
#ifndef __FSL_STREAM_ID_H
#define __FSL_STREAM_ID_H
-/* Stream IDs on ls2085a devices are not hardwired and are
+/* Stream IDs on ls2080a devices are not hardwired and are
* programmed by sw. There are a limited number of stream IDs
* available, and the partitioning of them is scenario dependent.
* This header defines the partitioning between legacy, PCI,
@@ -17,7 +17,7 @@
* on the specific hardware config-- e.g. perhaps not all
* PEX controllers are in use.
*
- * On LS2085 stream IDs are programmed in AMQ registers (32-bits) for
+ * On LS2080 stream IDs are programmed in AMQ registers (32-bits) for
* each of the different bus masters. The relationship between
* the AMQ registers and stream IDs is defined in the table below:
* AMQ bit streamID bit
diff --git a/arch/arm/include/asm/global_data.h
b/arch/arm/include/asm/global_data.h
index 4e3ea55..bd27281 100644
--- a/arch/arm/include/asm/global_data.h
+++ b/arch/arm/include/asm/global_data.h
@@ -46,7 +46,7 @@ struct arch_global_data {
u32 omap_boot_mode;
u8 omap_ch_flags;
#endif
-#ifdef CONFIG_FSL_LSCH3
+#if defined(CONFIG_FSL_LSCH3) && defined(CONFIG_SYS_FSL_HAS_DP_DDR)
unsigned long mem2_clk;
#endif
};
diff --git a/board/freescale/ls2085a/Kconfig b/board/freescale/ls2080a/Kconfig
similarity index 66%
rename from board/freescale/ls2085a/Kconfig
rename to board/freescale/ls2080a/Kconfig
index 042f85b..0b938ff 100644
--- a/board/freescale/ls2085a/Kconfig
+++ b/board/freescale/ls2080a/Kconfig
@@ -1,7 +1,7 @@
-if TARGET_LS2085A_EMU
+if TARGET_LS2080A_EMU
config SYS_BOARD
- default "ls2085a"
+ default "ls2080a"
config SYS_VENDOR
default "freescale"
@@ -10,14 +10,14 @@ config SYS_SOC
default "fsl-layerscape"
config SYS_CONFIG_NAME
- default "ls2085a_emu"
+ default "ls2080a_emu"
endif
-if TARGET_LS2085A_SIMU
+if TARGET_LS2080A_SIMU
config SYS_BOARD
- default "ls2085a"
+ default "ls2080a"
config SYS_VENDOR
default "freescale"
@@ -26,6 +26,6 @@ config SYS_SOC
default "fsl-layerscape"
config SYS_CONFIG_NAME
- default "ls2085a_simu"
+ default "ls2080a_simu"
endif
diff --git a/board/freescale/ls2080a/MAINTAINERS
b/board/freescale/ls2080a/MAINTAINERS
new file mode 100644
index 0000000..bb25084
--- /dev/null
+++ b/board/freescale/ls2080a/MAINTAINERS
@@ -0,0 +1,8 @@
+LS2080A BOARD
+M: York Sun <york...@freescale.com>
+S: Maintained
+F: board/freescale/ls2080a/
+F: include/configs/ls2080a_emu.h
+F: configs/ls2080a_emu_defconfig
+F: include/configs/ls2080a_simu.h
+F: configs/ls2080a_simu_defconfig
diff --git a/board/freescale/ls2080a/Makefile b/board/freescale/ls2080a/Makefile
new file mode 100644
index 0000000..47c7c74
--- /dev/null
+++ b/board/freescale/ls2080a/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2014-15 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += ls2080a.o
+obj-y += ddr.o
diff --git a/board/freescale/ls2085a/README b/board/freescale/ls2080a/README
similarity index 97%
rename from board/freescale/ls2085a/README
rename to board/freescale/ls2080a/README
index bc1d0bb..7e53f1f 100644
--- a/board/freescale/ls2085a/README
+++ b/board/freescale/ls2080a/README
@@ -1,4 +1,4 @@
-Freescale ls2085a_emu
+Freescale ls2080a_emu
This is a emulator target with limited peripherals.
diff --git a/board/freescale/ls2085a/ddr.c b/board/freescale/ls2080a/ddr.c
similarity index 99%
rename from board/freescale/ls2085a/ddr.c
rename to board/freescale/ls2080a/ddr.c
index 4884fa2..47d73ef 100644
--- a/board/freescale/ls2085a/ddr.c
+++ b/board/freescale/ls2080a/ddr.c
@@ -71,7 +71,7 @@ found:
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
-
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (ctrl_num == CONFIG_DP_DDR_CTRL) {
/* force DDR bus width to 32 bits */
popts->data_bus_width = 1;
@@ -79,6 +79,7 @@ found:
popts->burst_length = DDR_BL8;
popts->bstopre = 0; /* enable auto precharge */
}
+#endif
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
diff --git a/board/freescale/ls2085a/ddr.h b/board/freescale/ls2080a/ddr.h
similarity index 100%
rename from board/freescale/ls2085a/ddr.h
rename to board/freescale/ls2080a/ddr.h
diff --git a/board/freescale/ls2085a/ls2085a.c
b/board/freescale/ls2080a/ls2080a.c
similarity index 98%
rename from board/freescale/ls2085a/ls2085a.c
rename to board/freescale/ls2080a/ls2080a.c
index 27481e2..827fbf0 100644
--- a/board/freescale/ls2085a/ls2085a.c
+++ b/board/freescale/ls2080a/ls2080a.c
@@ -41,11 +41,13 @@ void detail_board_ddr_info(void)
puts("\nDDR ");
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
print_ddr_info(0);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (gd->bd->bi_dram[2].size) {
puts("\nDP-DDR ");
print_size(gd->bd->bi_dram[2].size, "");
print_ddr_info(CONFIG_DP_DDR_CTRL);
}
+#endif
}
int dram_init(void)
diff --git a/board/freescale/ls2085ardb/Kconfig
b/board/freescale/ls2080aqds/Kconfig
similarity index 67%
rename from board/freescale/ls2085ardb/Kconfig
rename to board/freescale/ls2080aqds/Kconfig
index cb40db9..2f997e9 100644
--- a/board/freescale/ls2085ardb/Kconfig
+++ b/board/freescale/ls2080aqds/Kconfig
@@ -1,8 +1,8 @@
-if TARGET_LS2085ARDB
+if TARGET_LS2080AQDS
config SYS_BOARD
- default "ls2085ardb"
+ default "ls2080aqds"
config SYS_VENDOR
default "freescale"
@@ -11,6 +11,6 @@ config SYS_SOC
default "fsl-layerscape"
config SYS_CONFIG_NAME
- default "ls2085ardb"
+ default "ls2080aqds"
endif
diff --git a/board/freescale/ls2080aqds/MAINTAINERS
b/board/freescale/ls2080aqds/MAINTAINERS
new file mode 100644
index 0000000..3d82482
--- /dev/null
+++ b/board/freescale/ls2080aqds/MAINTAINERS
@@ -0,0 +1,8 @@
+LS2080A BOARD
+M: Prabhakar Kushwaha <prabha...@freescale.com>
+S: Maintained
+F: board/freescale/ls2080aqds/
+F: board/freescale/ls2080a/ls2080aqds.c
+F: include/configs/ls2080aqds.h
+F: configs/ls2080aqds_defconfig
+F: configs/ls2080aqds_nand_defconfig
diff --git a/board/freescale/ls2085aqds/Makefile
b/board/freescale/ls2080aqds/Makefile
similarity index 83%
rename from board/freescale/ls2085aqds/Makefile
rename to board/freescale/ls2080aqds/Makefile
index da69a7d..e0da8a5 100644
--- a/board/freescale/ls2085aqds/Makefile
+++ b/board/freescale/ls2080aqds/Makefile
@@ -4,6 +4,6 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += ls2085aqds.o
+obj-y += ls2080aqds.o
obj-y += ddr.o
obj-y += eth.o
diff --git a/board/freescale/ls2085aqds/README
b/board/freescale/ls2080aqds/README
similarity index 95%
rename from board/freescale/ls2085aqds/README
rename to board/freescale/ls2080aqds/README
index e4a6f69..a4abb7e 100644
--- a/board/freescale/ls2085aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -1,19 +1,19 @@
Overview
--------
-The LS2085A Development System (QDS) is a high-performance computing,
-evaluation, and development platform that supports the QorIQ LS2085A
-Layerscape Architecture processor. The LS2085AQDS provides validation and
-SW development platform for the Freescale LS2085A processor series, with
+The LS2080A Development System (QDS) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS2080A
+Layerscape Architecture processor. The LS2080AQDS provides validation and
+SW development platform for the Freescale LS2080A processor series, with
a complete debugging environment.
-LS2085A SoC Overview
+LS2080A SoC Overview
------------------
-The LS2085A integrated multicore processor combines eight ARM Cortex-A57
+The LS2080A integrated multicore processor combines eight ARM Cortex-A57
processor cores with high-performance data path acceleration logic and network
and peripheral bus interfaces required for networking, telecom/datacom,
wireless infrastructure, and mil/aerospace applications.
-The LS2085A SoC includes the following function and features:
+The LS2080A SoC includes the following function and features:
- Eight 64-bit ARM Cortex-A57 CPUs
- 1 MB platform cache with ECC
@@ -50,7 +50,7 @@ The LS2085A SoC includes the following function and features:
- Service processor (SP) provides pre-boot initialization and secure-boot
capabilities
- LS2085AQDS board Overview
+ LS2080AQDS board Overview
-----------------------
- SERDES Connections, 16 lanes supporting:
- PCI Express - 3.0
diff --git a/board/freescale/ls2085ardb/ddr.c b/board/freescale/ls2080aqds/ddr.c
similarity index 98%
rename from board/freescale/ls2085ardb/ddr.c
rename to board/freescale/ls2080aqds/ddr.c
index 8d71ae1..ae681de 100644
--- a/board/freescale/ls2085ardb/ddr.c
+++ b/board/freescale/ls2080aqds/ddr.c
@@ -15,7 +15,9 @@ void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
u8 dq_mapping_0, dq_mapping_2, dq_mapping_3;
+#endif
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
int slot;
@@ -79,7 +81,7 @@ found:
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
-
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (ctrl_num == CONFIG_DP_DDR_CTRL) {
/* force DDR bus width to 32 bits */
popts->data_bus_width = 1;
@@ -114,6 +116,7 @@ found:
pdimm[slot].dq_mapping[16] = 0;
pdimm[slot].dq_mapping[17] = 0;
}
+#endif
/* To work at higher than 1333MT/s */
popts->half_strength_driver_enable = 0;
/*
diff --git a/board/freescale/ls2085aqds/ddr.h b/board/freescale/ls2080aqds/ddr.h
similarity index 100%
rename from board/freescale/ls2085aqds/ddr.h
rename to board/freescale/ls2080aqds/ddr.h
diff --git a/board/freescale/ls2085aqds/eth.c b/board/freescale/ls2080aqds/eth.c
similarity index 88%
rename from board/freescale/ls2085aqds/eth.c
rename to board/freescale/ls2080aqds/eth.c
index d116cd5..0637ecf 100644
--- a/board/freescale/ls2085aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -18,16 +18,16 @@
#include "../common/qixis.h"
-#include "ls2085aqds_qixis.h"
+#include "ls2080aqds_qixis.h"
#ifdef CONFIG_FSL_MC_ENET
- /* - In LS2085A there are only 16 SERDES lanes, spread across 2 SERDES banks.
+ /* - In LS2080A there are only 16 SERDES lanes, spread across 2 SERDES banks.
* Bank 1 -> Lanes A, B, C, D, E, F, G, H
* Bank 2 -> Lanes A,B, C, D, E, F, G, H
*/
- /* Mapping of 16 SERDES lanes to LS2085A QDS board slots. A value of '0' here
+ /* Mapping of 16 SERDES lanes to LS2080A QDS board slots. A value of '0' here
* means that the mapping must be determined dynamically, or that the lane
* maps to something other than a board slot.
*/
@@ -74,16 +74,16 @@ static int sgmii_riser_phy_addr[] = {
#define SFP_TX 0
static const char * const mdio_names[] = {
- "LS2085A_QDS_MDIO0",
- "LS2085A_QDS_MDIO1",
- "LS2085A_QDS_MDIO2",
- "LS2085A_QDS_MDIO3",
- "LS2085A_QDS_MDIO4",
- "LS2085A_QDS_MDIO5",
+ "LS2080A_QDS_MDIO0",
+ "LS2080A_QDS_MDIO1",
+ "LS2080A_QDS_MDIO2",
+ "LS2080A_QDS_MDIO3",
+ "LS2080A_QDS_MDIO4",
+ "LS2080A_QDS_MDIO5",
DEFAULT_WRIOP_MDIO2_NAME,
};
-struct ls2085a_qds_mdio {
+struct ls2080a_qds_mdio {
u8 muxval;
struct mii_dev *realbus;
};
@@ -95,7 +95,7 @@ static void sgmii_configure_repeater(int serdes_port)
int i, j, ret;
int dpmac_id = 0, dpmac, mii_bus = 0;
unsigned short value;
- char dev[2][20] = {"LS2085A_QDS_MDIO0", "LS2085A_QDS_MDIO3"};
+ char dev[2][20] = {"LS2080A_QDS_MDIO0", "LS2080A_QDS_MDIO3"};
uint8_t i2c_addr[] = {0x58, 0x59, 0x5a, 0x5b, 0x5c, 0x5d, 0x5f, 0x60};
uint8_t ch_a_eq[] = {0x1, 0x2, 0x3, 0x7};
@@ -222,7 +222,7 @@ static void qsgmii_configure_repeater(int dpmac)
uint8_t ch_b_eq[] = {0x1, 0x2, 0x3, 0x7};
uint8_t ch_b_ctl2[] = {0x81, 0x82, 0x83, 0x84};
- const char *dev = "LS2085A_QDS_MDIO0";
+ const char *dev = "LS2080A_QDS_MDIO0";
int ret = 0;
unsigned short value;
@@ -318,7 +318,7 @@ error:
return;
}
-static const char *ls2085a_qds_mdio_name_for_muxval(u8 muxval)
+static const char *ls2080a_qds_mdio_name_for_muxval(u8 muxval)
{
return mdio_names[muxval];
}
@@ -326,7 +326,7 @@ static const char *ls2085a_qds_mdio_name_for_muxval(u8
muxval)
struct mii_dev *mii_dev_for_muxval(u8 muxval)
{
struct mii_dev *bus;
- const char *name = ls2085a_qds_mdio_name_for_muxval(muxval);
+ const char *name = ls2080a_qds_mdio_name_for_muxval(muxval);
if (!name) {
printf("No bus for muxval %x\n", muxval);
@@ -343,7 +343,7 @@ struct mii_dev *mii_dev_for_muxval(u8 muxval)
return bus;
}
-static void ls2085a_qds_enable_SFP_TX(u8 muxval)
+static void ls2080a_qds_enable_SFP_TX(u8 muxval)
{
u8 brdcfg9;
@@ -353,7 +353,7 @@ static void ls2085a_qds_enable_SFP_TX(u8 muxval)
QIXIS_WRITE(brdcfg[9], brdcfg9);
}
-static void ls2085a_qds_mux_mdio(u8 muxval)
+static void ls2080a_qds_mux_mdio(u8 muxval)
{
u8 brdcfg4;
@@ -365,54 +365,54 @@ static void ls2085a_qds_mux_mdio(u8 muxval)
}
}
-static int ls2085a_qds_mdio_read(struct mii_dev *bus, int addr,
+static int ls2080a_qds_mdio_read(struct mii_dev *bus, int addr,
int devad, int regnum)
{
- struct ls2085a_qds_mdio *priv = bus->priv;
+ struct ls2080a_qds_mdio *priv = bus->priv;
- ls2085a_qds_mux_mdio(priv->muxval);
+ ls2080a_qds_mux_mdio(priv->muxval);
return priv->realbus->read(priv->realbus, addr, devad, regnum);
}
-static int ls2085a_qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+static int ls2080a_qds_mdio_write(struct mii_dev *bus, int addr, int devad,
int regnum, u16 value)
{
- struct ls2085a_qds_mdio *priv = bus->priv;
+ struct ls2080a_qds_mdio *priv = bus->priv;
- ls2085a_qds_mux_mdio(priv->muxval);
+ ls2080a_qds_mux_mdio(priv->muxval);
return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
}
-static int ls2085a_qds_mdio_reset(struct mii_dev *bus)
+static int ls2080a_qds_mdio_reset(struct mii_dev *bus)
{
- struct ls2085a_qds_mdio *priv = bus->priv;
+ struct ls2080a_qds_mdio *priv = bus->priv;
return priv->realbus->reset(priv->realbus);
}
-static int ls2085a_qds_mdio_init(char *realbusname, u8 muxval)
+static int ls2080a_qds_mdio_init(char *realbusname, u8 muxval)
{
- struct ls2085a_qds_mdio *pmdio;
+ struct ls2080a_qds_mdio *pmdio;
struct mii_dev *bus = mdio_alloc();
if (!bus) {
- printf("Failed to allocate ls2085a_qds MDIO bus\n");
+ printf("Failed to allocate ls2080a_qds MDIO bus\n");
return -1;
}
pmdio = malloc(sizeof(*pmdio));
if (!pmdio) {
- printf("Failed to allocate ls2085a_qds private data\n");
+ printf("Failed to allocate ls2080a_qds private data\n");
free(bus);
return -1;
}
- bus->read = ls2085a_qds_mdio_read;
- bus->write = ls2085a_qds_mdio_write;
- bus->reset = ls2085a_qds_mdio_reset;
- sprintf(bus->name, ls2085a_qds_mdio_name_for_muxval(muxval));
+ bus->read = ls2080a_qds_mdio_read;
+ bus->write = ls2080a_qds_mdio_write;
+ bus->reset = ls2080a_qds_mdio_reset;
+ sprintf(bus->name, ls2080a_qds_mdio_name_for_muxval(muxval));
pmdio->realbus = miiphy_get_dev_by_name(realbusname);
@@ -511,7 +511,7 @@ static void initialize_dpmac_to_slot(void)
}
}
-void ls2085a_handle_phy_interface_sgmii(int dpmac_id)
+void ls2080a_handle_phy_interface_sgmii(int dpmac_id)
{
int lane, slot;
struct mii_dev *bus;
@@ -632,7 +632,7 @@ serdes2:
}
}
-void ls2085a_handle_phy_interface_qsgmii(int dpmac_id)
+void ls2080a_handle_phy_interface_qsgmii(int dpmac_id)
{
int lane = 0, slot;
struct mii_dev *bus;
@@ -706,7 +706,7 @@ void ls2085a_handle_phy_interface_qsgmii(int dpmac_id)
qsgmii_configure_repeater(dpmac_id);
}
-void ls2085a_handle_phy_interface_xsgmii(int i)
+void ls2080a_handle_phy_interface_xsgmii(int i)
{
struct ccsr_gur __iomem *gur = (void *)CONFIG_SYS_FSL_GUTS_ADDR;
int serdes1_prtcl = (in_le32(&gur->rcwsr[28]) &
@@ -725,7 +725,7 @@ void ls2085a_handle_phy_interface_xsgmii(int i)
* error.
*/
wriop_set_phy_address(i, i + 4);
- ls2085a_qds_enable_SFP_TX(SFP_TX);
+ ls2080a_qds_enable_SFP_TX(SFP_TX);
break;
default:
@@ -778,25 +778,25 @@ int board_eth_init(bd_t *bis)
fm_memac_mdio_init(bis, memac_mdio1_info);
/* Register the muxing front-ends to the MDIO buses */
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT1);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT2);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT3);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT4);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT5);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT6);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT1);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT2);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT3);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT4);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT5);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO1_NAME, EMI1_SLOT6);
- ls2085a_qds_mdio_init(DEFAULT_WRIOP_MDIO2_NAME, EMI2);
+ ls2080a_qds_mdio_init(DEFAULT_WRIOP_MDIO2_NAME, EMI2);
for (i = WRIOP1_DPMAC1; i < NUM_WRIOP_PORTS; i++) {
switch (wriop_get_enet_if(i)) {
case PHY_INTERFACE_MODE_QSGMII:
- ls2085a_handle_phy_interface_qsgmii(i);
+ ls2080a_handle_phy_interface_qsgmii(i);
break;
case PHY_INTERFACE_MODE_SGMII:
- ls2085a_handle_phy_interface_sgmii(i);
+ ls2080a_handle_phy_interface_sgmii(i);
break;
case PHY_INTERFACE_MODE_XGMII:
- ls2085a_handle_phy_interface_xsgmii(i);
+ ls2080a_handle_phy_interface_xsgmii(i);
break;
default:
break;
diff --git a/board/freescale/ls2085aqds/ls2085aqds.c
b/board/freescale/ls2080aqds/ls2080aqds.c
similarity index 98%
rename from board/freescale/ls2085aqds/ls2085aqds.c
rename to board/freescale/ls2080aqds/ls2080aqds.c
index 36b059f..1f99072 100644
--- a/board/freescale/ls2085aqds/ls2085aqds.c
+++ b/board/freescale/ls2080aqds/ls2080aqds.c
@@ -21,7 +21,7 @@
#include <hwconfig.h>
#include "../common/qixis.h"
-#include "ls2085aqds_qixis.h"
+#include "ls2080aqds_qixis.h"
#define PIN_MUX_SEL_SDHC 0x00
#define PIN_MUX_SEL_DSPI 0x0a
@@ -226,11 +226,13 @@ void detail_board_ddr_info(void)
puts("\nDDR ");
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
print_ddr_info(0);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (gd->bd->bi_dram[2].size) {
puts("\nDP-DDR ");
print_size(gd->bd->bi_dram[2].size, "");
print_ddr_info(CONFIG_DP_DDR_CTRL);
}
+#endif
}
int dram_init(void)
diff --git a/board/freescale/ls2085aqds/ls2085aqds_qixis.h
b/board/freescale/ls2080aqds/ls2080aqds_qixis.h
similarity index 100%
rename from board/freescale/ls2085aqds/ls2085aqds_qixis.h
rename to board/freescale/ls2080aqds/ls2080aqds_qixis.h
diff --git a/board/freescale/ls2085aqds/Kconfig
b/board/freescale/ls2080ardb/Kconfig
similarity index 67%
rename from board/freescale/ls2085aqds/Kconfig
rename to board/freescale/ls2080ardb/Kconfig
index 8d6acba..fe02575 100644
--- a/board/freescale/ls2085aqds/Kconfig
+++ b/board/freescale/ls2080ardb/Kconfig
@@ -1,8 +1,8 @@
-if TARGET_LS2085AQDS
+if TARGET_LS2080ARDB
config SYS_BOARD
- default "ls2085aqds"
+ default "ls2080ardb"
config SYS_VENDOR
default "freescale"
@@ -11,6 +11,6 @@ config SYS_SOC
default "fsl-layerscape"
config SYS_CONFIG_NAME
- default "ls2085aqds"
+ default "ls2080ardb"
endif
diff --git a/board/freescale/ls2080ardb/MAINTAINERS
b/board/freescale/ls2080ardb/MAINTAINERS
new file mode 100644
index 0000000..aac8110
--- /dev/null
+++ b/board/freescale/ls2080ardb/MAINTAINERS
@@ -0,0 +1,8 @@
+LS2080A BOARD
+M: Prabhakar Kushwaha <prabha...@freescale.com>
+S: Maintained
+F: board/freescale/ls2080ardb/
+F: board/freescale/ls2080a/ls2080ardb.c
+F: include/configs/ls2080ardb.h
+F: configs/ls2080ardb_defconfig
+F: configs/ls2080ardb_nand_defconfig
diff --git a/board/freescale/ls2085ardb/Makefile
b/board/freescale/ls2080ardb/Makefile
similarity index 72%
rename from board/freescale/ls2085ardb/Makefile
rename to board/freescale/ls2080ardb/Makefile
index de383cc..6a52167 100644
--- a/board/freescale/ls2085ardb/Makefile
+++ b/board/freescale/ls2080ardb/Makefile
@@ -4,5 +4,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-y += ls2085ardb.o eth_ls2085rdb.o
+obj-y += ls2080ardb.o eth_ls2080rdb.o
obj-y += ddr.o
diff --git a/board/freescale/ls2085ardb/README
b/board/freescale/ls2080ardb/README
similarity index 94%
rename from board/freescale/ls2085ardb/README
rename to board/freescale/ls2080ardb/README
index 2f18243..7fc2569 100644
--- a/board/freescale/ls2085ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -1,17 +1,17 @@
Overview
--------
-The LS2085A Reference Design (RDB) is a high-performance computing,
-evaluation, and development platform that supports the QorIQ LS2085A
+The LS2080A Reference Design (RDB) is a high-performance computing,
+evaluation, and development platform that supports the QorIQ LS2080A
Layerscape Architecture processor.
-LS2085A SoC Overview
+LS2080A SoC Overview
------------------
-The LS2085A integrated multicore processor combines eight ARM Cortex-A57
+The LS2080A integrated multicore processor combines eight ARM Cortex-A57
processor cores with high-performance data path acceleration logic and network
and peripheral bus interfaces required for networking, telecom/datacom,
wireless infrastructure, and mil/aerospace applications.
-The LS2085A SoC includes the following function and features:
+The LS2080A SoC includes the following function and features:
- Eight 64-bit ARM Cortex-A57 CPUs
- 1 MB platform cache with ECC
@@ -48,7 +48,7 @@ The LS2085A SoC includes the following function and features:
- Service processor (SP) provides pre-boot initialization and secure-boot
capabilities
- LS2085ARDB board Overview
+ LS2080ARDB board Overview
-----------------------
- SERDES Connections, 16 lanes supporting:
- PCI Express - 3.0
diff --git a/board/freescale/ls2085aqds/ddr.c b/board/freescale/ls2080ardb/ddr.c
similarity index 98%
rename from board/freescale/ls2085aqds/ddr.c
rename to board/freescale/ls2080ardb/ddr.c
index 8d71ae1..ae681de 100644
--- a/board/freescale/ls2085aqds/ddr.c
+++ b/board/freescale/ls2080ardb/ddr.c
@@ -15,7 +15,9 @@ void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
u8 dq_mapping_0, dq_mapping_2, dq_mapping_3;
+#endif
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
int slot;
@@ -79,7 +81,7 @@ found:
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
pbsp->wrlvl_ctl_3);
-
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (ctrl_num == CONFIG_DP_DDR_CTRL) {
/* force DDR bus width to 32 bits */
popts->data_bus_width = 1;
@@ -114,6 +116,7 @@ found:
pdimm[slot].dq_mapping[16] = 0;
pdimm[slot].dq_mapping[17] = 0;
}
+#endif
/* To work at higher than 1333MT/s */
popts->half_strength_driver_enable = 0;
/*
diff --git a/board/freescale/ls2085ardb/ddr.h b/board/freescale/ls2080ardb/ddr.h
similarity index 100%
rename from board/freescale/ls2085ardb/ddr.h
rename to board/freescale/ls2080ardb/ddr.h
diff --git a/board/freescale/ls2085ardb/eth_ls2085rdb.c
b/board/freescale/ls2080ardb/eth_ls2080rdb.c
similarity index 98%
rename from board/freescale/ls2085ardb/eth_ls2085rdb.c
rename to board/freescale/ls2080ardb/eth_ls2080rdb.c
index d578757..db50e4e 100644
--- a/board/freescale/ls2085ardb/eth_ls2085rdb.c
+++ b/board/freescale/ls2080ardb/eth_ls2080rdb.c
@@ -97,7 +97,7 @@ int board_eth_init(bd_t *bis)
break;
default:
- printf("SerDes1 protocol 0x%x is not supported on LS2085aRDB\n",
+ printf("SerDes1 protocol 0x%x is not supported on LS2080aRDB\n",
srds_s1);
break;
}
diff --git a/board/freescale/ls2085ardb/ls2085ardb.c
b/board/freescale/ls2080ardb/ls2080ardb.c
similarity index 98%
rename from board/freescale/ls2085ardb/ls2085ardb.c
rename to board/freescale/ls2080ardb/ls2080ardb.c
index 761d7c8..2ae9d6c 100644
--- a/board/freescale/ls2085ardb/ls2085ardb.c
+++ b/board/freescale/ls2080ardb/ls2080ardb.c
@@ -20,7 +20,7 @@
#include <asm/arch/soc.h>
#include "../common/qixis.h"
-#include "ls2085ardb_qixis.h"
+#include "ls2080ardb_qixis.h"
#define PIN_MUX_SEL_SDHC 0x00
#define PIN_MUX_SEL_DSPI 0x0a
@@ -192,11 +192,13 @@ void detail_board_ddr_info(void)
puts("\nDDR ");
print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
print_ddr_info(0);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
if (gd->bd->bi_dram[2].size) {
puts("\nDP-DDR ");
print_size(gd->bd->bi_dram[2].size, "");
print_ddr_info(CONFIG_DP_DDR_CTRL);
}
+#endif
}
int dram_init(void)
diff --git a/board/freescale/ls2085ardb/ls2085ardb_qixis.h
b/board/freescale/ls2080ardb/ls2080ardb_qixis.h
similarity index 100%
rename from board/freescale/ls2085ardb/ls2085ardb_qixis.h
rename to board/freescale/ls2080ardb/ls2080ardb_qixis.h
diff --git a/board/freescale/ls2085a/MAINTAINERS
b/board/freescale/ls2085a/MAINTAINERS
deleted file mode 100644
index 90b4e47..0000000
--- a/board/freescale/ls2085a/MAINTAINERS
+++ /dev/null
@@ -1,8 +0,0 @@
-LS2085A BOARD
-M: York Sun <york...@freescale.com>
-S: Maintained
-F: board/freescale/ls2085a/
-F: include/configs/ls2085a_emu.h
-F: configs/ls2085a_emu_defconfig
-F: include/configs/ls2085a_simu.h
-F: configs/ls2085a_simu_defconfig
diff --git a/board/freescale/ls2085a/Makefile b/board/freescale/ls2085a/Makefile
deleted file mode 100644
index 701b35c..0000000
--- a/board/freescale/ls2085a/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# Copyright 2014 Freescale Semiconductor
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y += ls2085a.o
-obj-y += ddr.o
diff --git a/board/freescale/ls2085aqds/MAINTAINERS
b/board/freescale/ls2085aqds/MAINTAINERS
deleted file mode 100644
index fbed672..0000000
--- a/board/freescale/ls2085aqds/MAINTAINERS
+++ /dev/null
@@ -1,8 +0,0 @@
-LS2085A BOARD
-M: Prabhakar Kushwaha <prabha...@freescale.com>
-S: Maintained
-F: board/freescale/ls2085aqds/
-F: board/freescale/ls2085a/ls2085aqds.c
-F: include/configs/ls2085aqds.h
-F: configs/ls2085aqds_defconfig
-F: configs/ls2085aqds_nand_defconfig
diff --git a/board/freescale/ls2085ardb/MAINTAINERS
b/board/freescale/ls2085ardb/MAINTAINERS
deleted file mode 100644
index d5cce40..0000000
--- a/board/freescale/ls2085ardb/MAINTAINERS
+++ /dev/null
@@ -1,8 +0,0 @@
-LS2085A BOARD
-M: Prabhakar Kushwaha <prabha...@freescale.com>
-S: Maintained
-F: board/freescale/ls2085ardb/
-F: board/freescale/ls2085a/ls2085ardb.c
-F: include/configs/ls2085ardb.h
-F: configs/ls2085ardb_defconfig
-F: configs/ls2085ardb_nand_defconfig
diff --git a/configs/ls2085a_emu_defconfig b/configs/ls2080a_emu_defconfig
similarity index 93%
rename from configs/ls2085a_emu_defconfig
rename to configs/ls2080a_emu_defconfig
index 9c82e17..ebdde04 100644
--- a/configs/ls2085a_emu_defconfig
+++ b/configs/ls2080a_emu_defconfig
@@ -1,5 +1,5 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085A_EMU=y
+CONFIG_TARGET_LS2080A_EMU=y
CONFIG_SYS_EXTRA_OPTIONS="EMU,SYS_FSL_DDR4"
# CONFIG_CMD_CONSOLE is not set
# CONFIG_CMD_IMLS is not set
diff --git a/configs/ls2085a_simu_defconfig b/configs/ls2080a_simu_defconfig
similarity index 93%
rename from configs/ls2085a_simu_defconfig
rename to configs/ls2080a_simu_defconfig
index 9d04218..eb8000b 100644
--- a/configs/ls2085a_simu_defconfig
+++ b/configs/ls2080a_simu_defconfig
@@ -1,5 +1,5 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085A_SIMU=y
+CONFIG_TARGET_LS2080A_SIMU=y
CONFIG_SYS_EXTRA_OPTIONS="SIMU"
# CONFIG_CMD_CONSOLE is not set
# CONFIG_CMD_IMLS is not set
diff --git a/configs/ls2085ardb_defconfig b/configs/ls2080aqds_defconfig
similarity index 78%
rename from configs/ls2085ardb_defconfig
rename to configs/ls2080aqds_defconfig
index d0f16f2..afba06b 100644
--- a/configs/ls2085ardb_defconfig
+++ b/configs/ls2080aqds_defconfig
@@ -1,9 +1,9 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085ARDB=y
+CONFIG_TARGET_LS2080AQDS=y
# CONFIG_SYS_MALLOC_F is not set
CONFIG_DM_SPI=y
CONFIG_DM_SPI_FLASH=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2085a-rdb"
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-qds"
CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
diff --git a/configs/ls2085aqds_nand_defconfig
b/configs/ls2080aqds_nand_defconfig
similarity index 86%
rename from configs/ls2085aqds_nand_defconfig
rename to configs/ls2080aqds_nand_defconfig
index ce2a81c..40cf883 100644
--- a/configs/ls2085aqds_nand_defconfig
+++ b/configs/ls2080aqds_nand_defconfig
@@ -1,5 +1,5 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085AQDS=y
+CONFIG_TARGET_LS2080AQDS=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,NAND"
# CONFIG_CMD_SETEXPR is not set
diff --git a/configs/ls2085aqds_defconfig b/configs/ls2080ardb_defconfig
similarity index 78%
rename from configs/ls2085aqds_defconfig
rename to configs/ls2080ardb_defconfig
index 78b121d..301cd7f 100644
--- a/configs/ls2085aqds_defconfig
+++ b/configs/ls2080ardb_defconfig
@@ -1,9 +1,9 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085AQDS=y
+CONFIG_TARGET_LS2080ARDB=y
# CONFIG_SYS_MALLOC_F is not set
CONFIG_DM_SPI=y
CONFIG_DM_SPI_FLASH=y
-CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2085a-qds"
+CONFIG_DEFAULT_DEVICE_TREE="fsl-ls2080a-rdb"
CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4"
# CONFIG_CMD_SETEXPR is not set
CONFIG_OF_CONTROL=y
diff --git a/configs/ls2085ardb_nand_defconfig
b/configs/ls2080ardb_nand_defconfig
similarity index 86%
rename from configs/ls2085ardb_nand_defconfig
rename to configs/ls2080ardb_nand_defconfig
index 25a6f71..658c9ff 100644
--- a/configs/ls2085ardb_nand_defconfig
+++ b/configs/ls2080ardb_nand_defconfig
@@ -1,5 +1,5 @@
CONFIG_ARM=y
-CONFIG_TARGET_LS2085ARDB=y
+CONFIG_TARGET_LS2080ARDB=y
CONFIG_SPL=y
CONFIG_SYS_EXTRA_OPTIONS="SYS_FSL_DDR4,NAND"
# CONFIG_CMD_SETEXPR is not set
diff --git a/doc/README.fsl-trustzone-components
b/doc/README.fsl-trustzone-components
index a3afd1f..e122346 100644
--- a/doc/README.fsl-trustzone-components
+++ b/doc/README.fsl-trustzone-components
@@ -1,4 +1,4 @@
-Freescale ARM64 SoCs like LS2085A have ARM TrustZone components like
+Freescale ARM64 SoCs like LS2080A have ARM TrustZone components like
TZPC-BP147 (TrustZone Protection Controller) and TZASC-400 (TrustZone
Address Space Controller).
@@ -7,7 +7,7 @@ is left to a root-of-trust security software layer (running in
EL3
privilege mode), but still some configurations of these peripherals
might be required while the bootloader is executing in EL3 privilege
mode. The following sections define how to turn on these features for
-LS2085A like SoCs.
+LS2080A like SoCs.
TZPC-BP147 (TrustZone Protection Controller)
============================================
diff --git a/drivers/ddr/fsl/fsl_ddr_gen4.c b/drivers/ddr/fsl/fsl_ddr_gen4.c
index 49e4688..eefe709 100644
--- a/drivers/ddr/fsl/fsl_ddr_gen4.c
+++ b/drivers/ddr/fsl/fsl_ddr_gen4.c
@@ -107,14 +107,14 @@ void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t
*regs,
goto step2;
#ifdef CONFIG_SYS_FSL_ERRATUM_A008336
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
/* A008336 only applies to general DDR controllers */
if ((ctrl_num == 0) || (ctrl_num == 1))
#endif
ddr_out32(eddrtqcr1, 0x63b30002);
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A008514
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
/* A008514 only applies to DP-DDR controler */
if (ctrl_num == 2)
#endif
diff --git a/drivers/net/fsl-mc/mc.c b/drivers/net/fsl-mc/mc.c
index 5168b99..e1a02d1 100644
--- a/drivers/net/fsl-mc/mc.c
+++ b/drivers/net/fsl-mc/mc.c
@@ -1147,7 +1147,10 @@ static int do_fsl_mc(cmd_tbl_t *cmdtp, int flag, int
argc, char * const argv[])
switch (argv[1][0]) {
case 's': {
char sub_cmd;
- u64 mc_fw_addr, mc_dpc_addr, aiop_fw_addr;
+ u64 mc_fw_addr, mc_dpc_addr;
+#ifdef CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET
+ u64 aiop_fw_addr;
+#endif
sub_cmd = argv[2][0];
switch (sub_cmd) {
diff --git a/drivers/net/ldpaa_eth/Makefile b/drivers/net/ldpaa_eth/Makefile
index c37633f..5587aa6 100644
--- a/drivers/net/ldpaa_eth/Makefile
+++ b/drivers/net/ldpaa_eth/Makefile
@@ -6,4 +6,4 @@
obj-y += ldpaa_wriop.o
obj-y += ldpaa_eth.o
-obj-$(CONFIG_LS2085A) += ls2085a.o
+obj-$(CONFIG_LS2080A) += ls2080a.o
diff --git a/drivers/net/ldpaa_eth/ls2085a.c b/drivers/net/ldpaa_eth/ls2080a.c
similarity index 100%
rename from drivers/net/ldpaa_eth/ls2085a.c
rename to drivers/net/ldpaa_eth/ls2080a.c
diff --git a/drivers/pci/pcie_layerscape.c b/drivers/pci/pcie_layerscape.c
index 4cee038..8af6531 100644
--- a/drivers/pci/pcie_layerscape.c
+++ b/drivers/pci/pcie_layerscape.c
@@ -665,7 +665,7 @@ void ft_pci_setup(void *blob, bd_t *bd)
}
#endif
-#ifdef CONFIG_LS2085A
+#ifdef CONFIG_LS2080A
void pcie_set_available_streamids(void *blob, const char *pcie_path,
u32 *stream_ids, int count)
diff --git a/include/configs/ls2085a_common.h b/include/configs/ls2080a_common.h
similarity index 98%
rename from include/configs/ls2085a_common.h
rename to include/configs/ls2080a_common.h
index 0011e72..de542c2 100644
--- a/include/configs/ls2085a_common.h
+++ b/include/configs/ls2080a_common.h
@@ -11,7 +11,7 @@
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_FSL_LSCH3
-#define CONFIG_LS2085A
+#define CONFIG_LS2080A
#define CONFIG_MP
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
@@ -20,7 +20,7 @@
#define CONFIG_ARM_ERRATA_828024
#define CONFIG_ARM_ERRATA_826974
-#include <asm/arch/ls2085a_stream_id.h>
+#include <asm/arch/ls2080a_stream_id.h>
#include <asm/arch/config.h>
#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
#define CONFIG_SYS_HAS_SERDES
@@ -80,6 +80,7 @@
#define CPU_RELEASE_ADDR secondary_boot_func
#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
/*
* DDR controller use 0 as the base address for binding.
@@ -88,6 +89,7 @@
#define CONFIG_SYS_DP_DDR_BASE_PHY 0
#define CONFIG_DP_DDR_CTRL 2
#define CONFIG_DP_DDR_NUM_CTRLS 1
+#endif
/* Generic Timer Definitions */
/*
@@ -183,8 +185,10 @@ unsigned long long get_qixis_addr(void);
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
+#ifndef CONFIG_LS2080A
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
+#endif
/*
* Carve out a DDR region which will not be used by u-boot/Linux
@@ -205,7 +209,7 @@ unsigned long long get_qixis_addr(void);
#define CONFIG_PCIE3 /* PCIE controler 3 */
#define CONFIG_PCIE4 /* PCIE controler 4 */
#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
-#define FSL_PCIE_COMPAT "fsl,ls2085a-pcie"
+#define FSL_PCIE_COMPAT "fsl,ls2080a-pcie"
#define CONFIG_SYS_PCI_64BIT
diff --git a/include/configs/ls2085a_emu.h b/include/configs/ls2080a_emu.h
similarity index 94%
rename from include/configs/ls2085a_emu.h
rename to include/configs/ls2080a_emu.h
index 2d68e1b..6400f4f 100644
--- a/include/configs/ls2085a_emu.h
+++ b/include/configs/ls2080a_emu.h
@@ -7,10 +7,10 @@
#ifndef __LS2_EMU_H
#define __LS2_EMU_H
-#include "ls2085a_common.h"
+#include "ls2080a_common.h"
-#define CONFIG_IDENT_STRING " LS2085A-EMU"
-#define CONFIG_BOOTP_VCI_STRING "U-boot.LS2085A-EMU"
+#define CONFIG_IDENT_STRING " LS2080A-EMU"
+#define CONFIG_BOOTP_VCI_STRING "U-boot.LS2080A-EMU"
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 133333333
@@ -27,7 +27,9 @@
#define CONFIG_SYS_SPD_BUS_NUM 1 /* SPD on I2C bus 1 */
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
+#endif
#define CONFIG_FSL_DDR_SYNC_REFRESH
diff --git a/include/configs/ls2085a_simu.h b/include/configs/ls2080a_simu.h
similarity index 96%
rename from include/configs/ls2085a_simu.h
rename to include/configs/ls2080a_simu.h
index bd15b3d..666df80 100644
--- a/include/configs/ls2085a_simu.h
+++ b/include/configs/ls2080a_simu.h
@@ -7,10 +7,10 @@
#ifndef __LS2_SIMU_H
#define __LS2_SIMU_H
-#include "ls2085a_common.h"
+#include "ls2080a_common.h"
-#define CONFIG_IDENT_STRING " LS2085A-SIMU"
-#define CONFIG_BOOTP_VCI_STRING "U-boot.LS2085A-SIMU"
+#define CONFIG_IDENT_STRING " LS2080A-SIMU"
+#define CONFIG_BOOTP_VCI_STRING "U-boot.LS2080A-SIMU"
#define CONFIG_SYS_CLK_FREQ 100000000
#define CONFIG_DDR_CLK_FREQ 133333333
@@ -20,7 +20,9 @@
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
+#endif
/* SMSC 91C111 ethernet configuration */
#define CONFIG_SMC91111
diff --git a/include/configs/ls2085aqds.h b/include/configs/ls2080aqds.h
similarity index 99%
rename from include/configs/ls2085aqds.h
rename to include/configs/ls2080aqds.h
index 99690ef..b8bdf62 100644
--- a/include/configs/ls2085aqds.h
+++ b/include/configs/ls2080aqds.h
@@ -7,7 +7,7 @@
#ifndef __LS2_QDS_H
#define __LS2_QDS_H
-#include "ls2085a_common.h"
+#include "ls2080a_common.h"
#define CONFIG_DISPLAY_BOARDINFO
@@ -35,7 +35,9 @@ unsigned long get_board_ddr_clk(void);
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
+#endif
#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
diff --git a/include/configs/ls2085ardb.h b/include/configs/ls2080ardb.h
similarity index 99%
rename from include/configs/ls2085ardb.h
rename to include/configs/ls2080ardb.h
index f36253d..65d4f64 100644
--- a/include/configs/ls2085ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -7,7 +7,7 @@
#ifndef __LS2_RDB_H
#define __LS2_RDB_H
-#include "ls2085a_common.h"
+#include "ls2080a_common.h"
#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX 2
@@ -37,7 +37,9 @@ unsigned long get_board_sys_clk(void);
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR 1
+#endif
#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
diff --git a/include/linux/usb/xhci-fsl.h b/include/linux/usb/xhci-fsl.h
index 602a413..80b7718 100644
--- a/include/linux/usb/xhci-fsl.h
+++ b/include/linux/usb/xhci-fsl.h
@@ -54,9 +54,9 @@ struct fsl_xhci {
#if defined(CONFIG_LS102XA)
#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS102XA_XHCI_USB1_ADDR
#define CONFIG_SYS_FSL_XHCI_USB2_ADDR 0
-#elif defined(CONFIG_LS2085A)
-#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS2085A_XHCI_USB1_ADDR
-#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_LS2085A_XHCI_USB2_ADDR
+#elif defined(CONFIG_LS2080A)
+#define CONFIG_SYS_FSL_XHCI_USB1_ADDR CONFIG_SYS_LS2080A_XHCI_USB1_ADDR
+#define CONFIG_SYS_FSL_XHCI_USB2_ADDR CONFIG_SYS_LS2080A_XHCI_USB2_ADDR
#endif
#define FSL_USB_XHCI_ADDR {CONFIG_SYS_FSL_XHCI_USB1_ADDR, \
--
1.9.1
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
