Hi Marek, On Fri, 20 Nov 2015 17:17:33 +0100 Marek Vasut <ma...@denx.de> wrote:
> This board was constantly parasiting on the CV SoCDK, so split it > into it's own separate directory. Moreover, the board config was > missing important bits, like simple-bus support in SPL, the DRAM > configuration was incorrect and the DTS was also missing the pre > reloc bits. > > Signed-off-by: Marek Vasut <ma...@denx.de> > Cc: Stefan Roese <s...@denx.de> > Cc: Dinh Nguyen <dingu...@opensource.altera.com> > Cc: Dinh Nguyen <dinh.li...@gmail.com> > Reviewed-by: Stefan Roese <s...@denx.de> > --- > arch/arm/dts/socfpga_cyclone5_socrates.dts | 5 + > arch/arm/mach-socfpga/Kconfig | 7 + > board/ebv/socrates/MAINTAINERS | 6 + > board/ebv/socrates/Makefile | 9 + > board/ebv/socrates/qts/iocsr_config.h | 660 > +++++++++++++++++++++++++++++ > board/ebv/socrates/qts/pinmux_config.h | 219 ++++++++++ > board/ebv/socrates/qts/pll_config.h | 85 ++++ > board/ebv/socrates/qts/sdram_config.h | 341 +++++++++++++++ > board/ebv/socrates/socfpga.c | 85 ++++ > configs/socfpga_socrates_defconfig | 3 +- > include/configs/socfpga_socrates.h | 97 +++++ > 11 files changed, 1516 insertions(+), 1 deletion(-) > create mode 100644 board/ebv/socrates/MAINTAINERS > create mode 100644 board/ebv/socrates/Makefile > create mode 100644 board/ebv/socrates/qts/iocsr_config.h > create mode 100644 board/ebv/socrates/qts/pinmux_config.h > create mode 100644 board/ebv/socrates/qts/pll_config.h > create mode 100644 board/ebv/socrates/qts/sdram_config.h > create mode 100644 board/ebv/socrates/socfpga.c > create mode 100644 include/configs/socfpga_socrates.h > [snip] SoCrates (1.2) boots now properly: U-Boot SPL 2016.01-rc1 (Nov 23 2015 - 14:34:13) drivers/ddr/altera/sequencer.c: Preparing to start memory calibration drivers/ddr/altera/sequencer.c: CALIBRATION PASSED drivers/ddr/altera/sequencer.c: Calibration complete Trying to boot from MMC U-Boot 2016.01-rc1 (Nov 23 2015 - 14:34:13 +0100) CPU: Altera SoCFPGA Platform FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0 BOOT: SD/MMC Internal Transceiver (3.0V) Watchdog enabled I2C: ready DRAM: 1 GiB MMC: SOCFPGA DWMMC: 0 *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Model: EBV SOCrates Net: Error: ethernet@ff702000 address not set. No ethernet found. Hit any key to stop autoboot: 0 => Applied after manual fix of this: default "socfpga_sockit" if TARGET_SOCFPGA_TERASIC_SOCKIT + default "socfpga_sockit" if TARGET_SOCFPGA_EBV_SOCRATES I don't understand the issue with Ethernet: "Error: ethernet@ff702000 address not set." Otherwise Tested-By: Jan Viktorin <vikto...@rehivetech.com> -- Jan Viktorin E-mail: vikto...@rehivetech.com System Architect Web: www.RehiveTech.com RehiveTech Brno, Czech Republic _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot