On 04/05/2016 01:30 PM, Dan Murphy wrote: > On 04/05/2016 12:36 PM, Michal Simek wrote: >> On 5.4.2016 19:18, Dan Murphy wrote: >>> Michal >>> >>> On 04/05/2016 12:01 PM, Michal Simek wrote: >>>> On 5.4.2016 17:05, Dan Murphy wrote: >>>>> Not all devices use the same internal delay or fifo depth. >>>>> Add the ability to set the internal delay for rx or tx and the >>>>> fifo depth via the devicetree. If the value is not set in the >>>>> devicetree then set the delay to the default. >>>>> >>>>> If devicetree is not used then use the default defines within the >>>>> driver. >>>>> >>>>> Signed-off-by: Dan Murphy <dmur...@ti.com> >>>>> --- >>>>> >>>>> RFC->v1 - Added devicetree support - >>>>> https://patchwork.ozlabs.org/patch/604113/ >>>>> >>>>> drivers/net/phy/ti.c | 81 >>>>> ++++++++++++++++++++++++++++++++++++++++++++++------ >>>>> 1 file changed, 73 insertions(+), 8 deletions(-) >>>>> >>>>> diff --git a/drivers/net/phy/ti.c b/drivers/net/phy/ti.c >>>>> index c3912d5..e91a6ed 100644 >>>>> --- a/drivers/net/phy/ti.c >>>>> +++ b/drivers/net/phy/ti.c >>>>> @@ -6,6 +6,14 @@ >>>>> */ >>>>> #include <common.h> >>>>> #include <phy.h> >>>>> +#include <linux/compat.h> >>>>> +#include <malloc.h> >>>>> + >>>>> +#include <fdtdec.h> >>>>> +#include <dm.h> >>>>> +#include <dt-bindings/net/ti-dp83867.h> >>>>> + >>>>> +DECLARE_GLOBAL_DATA_PTR; >>>>> >>>>> /* TI DP83867 */ >>>>> #define DP83867_DEVADDR 0x1f >>>>> @@ -57,6 +65,17 @@ >>>>> #define MII_MMD_CTRL_INCR_RDWT 0x8000 /* post increment on reads & >>>>> writes */ >>>>> #define MII_MMD_CTRL_INCR_ON_WT 0xC000 /* post increment on writes only >>>>> */ >>>>> >>>>> +/* User setting - can be taken from DTS */ >>>>> +#define DEFAULT_RX_ID_DELAY DP83867_RGMIIDCTL_2_25_NS >>>>> +#define DEFAULT_TX_ID_DELAY DP83867_RGMIIDCTL_2_75_NS >>>>> +#define DEFAULT_FIFO_DEPTH DP83867_PHYCR_FIFO_DEPTH_4_B_NIB >>>>> + >>>>> +struct dp83867_private { >>>>> + int rx_id_delay; >>>>> + int tx_id_delay; >>>>> + int fifo_depth; >>>>> +}; >>>>> + >>>>> /** >>>>> * phy_read_mmd_indirect - reads data from the MMD registers >>>>> * @phydev: The PHY device bus >>>>> @@ -134,16 +153,58 @@ static inline bool phy_interface_is_rgmii(struct >>>>> phy_device *phydev) >>>>> phydev->interface <= PHY_INTERFACE_MODE_RGMII_TXID; >>>>> } >>>>> >>>>> -/* User setting - can be taken from DTS */ >>>>> -#define RX_ID_DELAY 8 >>>>> -#define TX_ID_DELAY 0xa >>>>> -#define FIFO_DEPTH 1 >>>>> +#if defined(CONFIG_DM_ETH) >>>>> +/** >>>>> + * dp83867_data_init - Convenience function for setting PHY specific data >>>>> + * >>>>> + * @phydev: the phy_device struct >>>>> + */ >>>>> +static int dp83867_of_init(struct phy_device *phydev) >>>>> +{ >>>>> + struct dp83867_private *dp83867 = phydev->priv; >>>>> + struct udevice *dev = phydev->dev; >>>>> + >>>>> + dp83867->rx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset, >>>>> + "ti,rx_int_delay", DEFAULT_RX_ID_DELAY); >>>>> + >>>>> + dp83867->tx_id_delay = fdtdec_get_uint(gd->fdt_blob, dev->of_offset, >>>>> + "ti,tx_int_delay", DEFAULT_TX_ID_DELAY); >>>>> + >>>> this is not aligned with the binding you sent. >>>> ti,rx-internal-delay >>>> and >>>> ti,tx-internal-delay >>> You are right I will fix it and then make the same change in the kernel >> Why not just follow linux binding? >> Changing binding in kernel will end up in deprecated binding for nothing. > What specific Linux binding are you referring to? > > I don't see this binding getting changed as the internal delay and fifo depth > are board configurable options and I don't for see the register map changing > for this > device.
I see it now. Will submit v3 of the driver but I will wait for additional comments before sending tomorrow. Dan > Dan > > >> Thanks, >> Michal >> >> > -- ------------------ Dan Murphy _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot