Hi: York 1, There is an issue for sdk2.0 kernel that the nor-flash can't be probed . we can fix it as follow:
$make menuconfig x -> Device Drivers x -> Memory Technology Device (MTD) support x -> RAM/ROM/Flash chip drivers x -> Flash chip driver advanced configuration options x -> Flash cmd/query data swapping x x ( ) NO x x (X) BIG_ENDIAN_BYTE x x ( ) LITTLE_ENDIAN_BYTE Enable BIG_ENDIAN_BYTE . 2, The spi-nor flash can working on ls1043aqds , and I use the sdk2.0 kernel (ce5a3841f3). [ 1.598954] m25p80 spi0.0: n25q128a11 (16384 Kbytes) [ 1.603923] 4 cmdlinepart partitions found on MTD device spi0.0 [ 1.609842] Creating 4 MTD partitions on "spi0.0": [ 1.614624] 0x000000000000-0x000000100000 : "uboot" [ 1.624205] ftl_cs: FTL header not found. [ 1.628421] 0x000000100000-0x000000600000 : "kernel" [ 1.638086] ftl_cs: FTL header not found. [ 1.642316] 0x000000600000-0x000000700000 : "dtb" [ 1.651702] ftl_cs: FTL header not found. [ 1.655932] 0x000000700000-0x000001000000 : "file_system" [ 1.666028] ftl_cs: FTL header not found. Best Regards Wenbin Song > -----Original Message----- > From: York Sun [mailto:york....@nxp.com] > Sent: Wednesday, April 06, 2016 5:02 AM > To: Wenbin Song <wenbin.s...@nxp.com>; Mingkai Hu > <mingkai...@nxp.com>; u-boot@lists.denx.de > Cc: Qianyu Gong <qianyu.g...@nxp.com>; Shaohui Xie > <shaohui....@nxp.com>; Zhiqiang Hou <zhiqiang....@nxp.com> > Subject: Re: [PATCH] armv8/ls1043a: Add MTD partition scheme > > On 04/05/2016 01:32 PM, York Sun wrote: > > On 04/01/2016 02:37 AM, Wenbin Song wrote: > >> Add and share the the MTD partition scheme with kernel by defualt > bootargs. > >> And add the "mtdparts" env. > >> > >> Signed-off-by: Wenbin Song <wenbin.s...@nxp.com> > >> --- > >> include/configs/ls1043a_common.h | 22 ++++++++++++++++++++-- > >> 1 file changed, 20 insertions(+), 2 deletions(-) > >> > >> diff --git a/include/configs/ls1043a_common.h > >> b/include/configs/ls1043a_common.h > >> index fd243b1..6964873 100644 > >> --- a/include/configs/ls1043a_common.h > >> +++ b/include/configs/ls1043a_common.h > >> @@ -236,6 +236,21 @@ > >> #define CONFIG_HWCONFIG > >> #define HWCONFIG_BUFFER_SIZE 128 > >> > >> +#if defined(CONFIG_QSPI_BOOT) || defined(CONFIG_SD_BOOT_QSPI) > >> +#define MTDPARTS_DEFAULT "mtdparts=spi0.0:1m(uboot)," \ > >> + "5m(kernel),1m(dtb),9m(file_system)" > >> +#else > >> +#define MTDPARTS_DEFAULT > "mtdparts=60000000.nor:1m(nor_bank0_rcw)," \ > >> + "1m(nor_bank0_uboot),1m(nor_bank0_uboot_env)," > \ > >> + "1m(nor_bank0_fman_uconde),40m(nor_bank0_fit)," > \ > >> + "1m(nor_bank4_rcw),1m(nor_bank4_uboot)," \ > >> + > "1m(nor_bank4_uboot_env),1m(nor_bank4_fman_ucode)," \ > >> + "40m(nor_bank4_fit);7e800000.flash:" \ > >> + "1m(nand_uboot),1m(nand_uboot_env)," \ > >> + "20m(nand_fit);spi0.0:1m(uboot)," \ > >> + "5m(kernel),1m(dtb),9m(file_system)" > >> +#endif > >> + > >> /* Initial environment variables */ > >> #define CONFIG_EXTRA_ENV_SETTINGS \ > >> "hwconfig=fsl_ddr:bank_intlv=auto\0" \ > >> @@ -248,10 +263,13 @@ > >> "kernel_start=0x61100000\0" \ > >> "kernel_load=0xa0000000\0" \ > >> "kernel_size=0x2800000\0" \ > >> - "console=ttyAMA0,38400n8\0" > >> + "console=ttyAMA0,38400n8\0" \ > >> + "mtdparts=" MTDPARTS_DEFAULT "\0" > >> > >> #define CONFIG_BOOTARGS "console=ttyS0,115200 > root=/dev/ram0 " \ > >> - "earlycon=uart8250,mmio,0x21c0500" > >> + "earlycon=uart8250,mmio,0x21c0500 " \ > >> + MTDPARTS_DEFAULT > > > > You could use $mtdparts here so your bootcmd doesn't get too long. > > > > Wenbin, > > A related question regarding MTD, how do you make NOR MTD device working > on these boards (ls1043aqds and ls1043ardb)? This is a common file for both > RDB and QDS. I presume you have verified on both. I have nand working on > both, spi-nor working on rdb only. I don't have NOR working on either of them. > It may be not a U-Boot issue though. > > York > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot