Hi Simon, > -----Original Message----- > From: Siva Durga Prasad Paladugu > Sent: Tuesday, June 28, 2016 11:38 AM > To: 'Simon Glass' <s...@chromium.org>; U-Boot Mailing List <u- > b...@lists.denx.de> > Cc: Marek Vasut <ma...@denx.de>; 'Hans de Goede' <hdego...@redhat.com> > Subject: RE: [U-Boot] [PATCH 24/27] dm: zynq: usb: Convert to > CONFIG_DM_USB > > Hi Simon, > > > -----Original Message----- > > From: U-Boot [mailto:u-boot-boun...@lists.denx.de] On Behalf Of Simon > > Glass > > Sent: Monday, June 13, 2016 11:01 AM > > To: U-Boot Mailing List <u-boot@lists.denx.de> > > Cc: Marek Vasut <ma...@denx.de> > > Subject: [U-Boot] [PATCH 24/27] dm: zynq: usb: Convert to > > CONFIG_DM_USB > > > > Convert zynq USB to driver model. It does not actually work, but the > > error is similar. > > > > Before: > > > > Zynq> dm tree > > Class Probed Name > > ---------------------------------------- > > root [ + ] root_driver > > rsa_mod_exp [ ] |-- mod_exp_sw > > simple_bus [ + ] `-- amba > > gpio [ ] |-- gpio@e000a000 > > serial [ + ] |-- serial@e0001000 > > spi [ + ] |-- spi@e000d000 > > spi_flash [ ] | `-- spi_flash@0:0 > > eth [ + ] |-- ethernet@e000b000 > > mmc [ + ] |-- sdhci@e0100000 > > simple_bus [ ] `-- slcr@f8000000 > > Zynq> usb start > > starting USB... > > USB0: USB EHCI 1.00 > > scanning bus 0 for devices... 2 USB Device(s) found > > USB1: usb1 wrong num MIO: 0, Index 1 > > lowlevel init failed > > scanning usb for storage devices... 0 Storage Device(s) found > > Zynq> > > > > After: > > > > Zynq> dm tree > > Class Probed Name > > ---------------------------------------- > > root [ + ] root_driver > > rsa_mod_exp [ ] |-- mod_exp_sw > > simple_bus [ + ] `-- amba > > gpio [ ] |-- gpio@e000a000 > > serial [ + ] |-- serial@e0001000 > > spi [ + ] |-- spi@e000d000 > > spi_flash [ ] | `-- spi_flash@0:0 > > eth [ + ] |-- ethernet@e000b000 > > mmc [ + ] |-- sdhci@e0100000 > > blk [ + ] | `-- sd...@e0100000.blk > > simple_bus [ ] |-- slcr@f8000000 > > usb [ + ] `-- usb@e0002000 > > Zynq> usb start > > starting USB... > > USB0: USB EHCI 1.00 > > scanning bus 0 for devices... Error: Cannot find high speed parent of > > usb-1 device EHCI timed out on TD - token=0x80008c80 unable to get > > device descriptor (error=-1) failed, error -1 > > Zynq> > > > > Signed-off-by: Simon Glass <s...@chromium.org> > > --- > > > > arch/arm/Kconfig | 2 + > > drivers/usb/host/ehci-zynq.c | 102 > > +++++++++++++++++++++---------------------- > > 2 files changed, 52 insertions(+), 52 deletions(-) > > > > diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index > > 1af9c35..2b501eb > > 100644 > > --- a/arch/arm/Kconfig > > +++ b/arch/arm/Kconfig > > @@ -643,6 +643,7 @@ config ARCH_ZYNQ > > select DM_SERIAL > > select DM_SPI_FLASH > > select SPL_SEPARATE_BSS if SPL > > + select DM_USB > > > > config ARCH_ZYNQMP > > bool "Support Xilinx ZynqMP Platform" > > @@ -651,6 +652,7 @@ config ARCH_ZYNQMP > > select OF_CONTROL > > select DM_SERIAL > > select SUPPORT_SPL > > + select DM_USB > > > > config TEGRA > > bool "NVIDIA Tegra" > > diff --git a/drivers/usb/host/ehci-zynq.c > > b/drivers/usb/host/ehci-zynq.c index 37a7935..b45c68d 100644 > > --- a/drivers/usb/host/ehci-zynq.c > > +++ b/drivers/usb/host/ehci-zynq.c > > @@ -7,55 +7,47 @@ > > */ > > > > #include <common.h> > > +#include <dm.h> > > +#include <usb.h> > > #include <asm/arch/hardware.h> > > #include <asm/arch/sys_proto.h> > > #include <asm/io.h> > > -#include <usb.h> > > #include <usb/ehci-ci.h> > > #include <usb/ulpi.h> > > > > #include "ehci.h" > > > > -#define ZYNQ_USB_USBCMD_RST 0x0000002 > > -#define ZYNQ_USB_USBCMD_STOP 0x0000000 > > -#define ZYNQ_USB_NUM_MIO 12 > > +struct zynq_ehci_priv { > Please add below member to this structure as per my conversation with Hans de > Goede. > This solves the usb issue which you stated, > Struct struct ehci_ctrl ehcictrl;
Can you add this element to structure (zynq_ehic_priv) as mentioned above in your patch? Thanks, Siva > > > Thanks, > Siva > > > + struct usb_ehci *ehci; > > +}; > > > > -/* > > - * Create the appropriate control structures to manage > > - * a new EHCI host controller. > > - */ > > -int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr > > **hccr, > > - struct ehci_hcor **hcor) > > +static int ehci_zynq_ofdata_to_platdata(struct udevice *dev) > > { > > - struct usb_ehci *ehci; > > + struct zynq_ehci_priv *priv = dev_get_priv(dev); > > + > > + priv->ehci = (struct usb_ehci *)dev_get_addr_ptr(dev); > > + if (!priv->ehci) > > + return -EINVAL; > > + > > + return 0; > > +} > > + > > +static int ehci_zynq_probe(struct udevice *dev) { > > + struct usb_platdata *plat = dev_get_platdata(dev); > > + struct zynq_ehci_priv *priv = dev_get_priv(dev); > > + struct ehci_hccr *hccr; > > + struct ehci_hcor *hcor; > > struct ulpi_viewport ulpi_vp; > > - int ret, mio_usb; > > /* Used for writing the ULPI data address */ > > struct ulpi_regs *ulpi = (struct ulpi_regs *)0; > > + int ret; > > > > - if (!index) { > > - mio_usb = zynq_slcr_get_mio_pin_status("usb0"); > > - if (mio_usb != ZYNQ_USB_NUM_MIO) { > > - printf("usb0 wrong num MIO: %d, Index %d\n", > > mio_usb, > > - index); > > - return -1; > > - } > > - ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0; > > - } else { > > - mio_usb = zynq_slcr_get_mio_pin_status("usb1"); > > - if (mio_usb != ZYNQ_USB_NUM_MIO) { > > - printf("usb1 wrong num MIO: %d, Index %d\n", > > mio_usb, > > - index); > > - return -1; > > - } > > - ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1; > > - } > > - > > - *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); > > - *hcor = (struct ehci_hcor *)((uint32_t) *hccr + > > - HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); > > + hccr = (struct ehci_hccr *)((uint32_t)&priv->ehci->caplength); > > + hcor = (struct ehci_hcor *)((uint32_t) hccr + > > + HC_LENGTH(ehci_readl(&hccr->cr_capbase))); > > > > - ulpi_vp.viewport_addr = (u32)&ehci->ulpi_viewpoint; > > + ulpi_vp.viewport_addr = (u32)&priv->ehci->ulpi_viewpoint; > > ulpi_vp.port_num = 0; > > > > ret = ulpi_init(&ulpi_vp); > > @@ -77,28 +69,34 @@ int ehci_hcd_init(int index, enum usb_init_type > > init, struct ehci_hccr **hccr, > > ulpi_write(&ulpi_vp, &ulpi->otg_ctrl_set, > > ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT); > > > > - return 0; > > + return ehci_register(dev, hccr, hcor, NULL, 0, plat->init_type); > > } > > > > -/* > > - * Destroy the appropriate control structures corresponding > > - * the the EHCI host controller. > > - */ > > -int ehci_hcd_stop(int index) > > +static int ehci_zynq_remove(struct udevice *dev) > > { > > - struct usb_ehci *ehci; > > - > > - if (!index) > > - ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0; > > - else > > - ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1; > > + int ret; > > > > - /* Stop controller */ > > - writel(ZYNQ_USB_USBCMD_STOP, &ehci->usbcmd); > > - udelay(1000); > > - > > - /* Initiate controller reset */ > > - writel(ZYNQ_USB_USBCMD_RST, &ehci->usbcmd); > > + ret = ehci_deregister(dev); > > + if (ret) > > + return ret; > > > > return 0; > > } > > + > > +static const struct udevice_id ehci_zynq_ids[] = { > > + { .compatible = "xlnx,zynq-usb-2.20a" }, > > + { } > > +}; > > + > > +U_BOOT_DRIVER(ehci_zynq) = { > > + .name = "ehci_zynq", > > + .id = UCLASS_USB, > > + .of_match = ehci_zynq_ids, > > + .ofdata_to_platdata = ehci_zynq_ofdata_to_platdata, > > + .probe = ehci_zynq_probe, > > + .remove = ehci_zynq_remove, > > + .ops = &ehci_usb_ops, > > + .platdata_auto_alloc_size = sizeof(struct usb_platdata), > > + .priv_auto_alloc_size = sizeof(struct zynq_ehci_priv), > > + .flags = DM_FLAG_ALLOC_PRIV_DMA, > > +}; > > -- > > 2.8.0.rc3.226.g39d4020 > > > > _______________________________________________ > > U-Boot mailing list > > U-Boot@lists.denx.de > > http://lists.denx.de/mailman/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot