Now i found and add 2 in mmc_extra_slot_number config, compile and burn on marsboard emmc(sdc2) Got absolutely the same output, as from my board, except mmc number
U-Boot SPL 2016.11-rc1-g4dc34be-dirty (Oct 12 2016 - 18:48:07) DRAM: 1024 MiB CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 Trying to boot from MMC2 CMD_SEND:0 ..ARG... 0x00000000 ..MMC_RSP_NONE CMD_SEND:8 ..ARG... 0x00000000 ..RET... -110 CMD_SEND:55 ..ARG... 0x00000000 ..RET... -110 CMD_SEND:0 ..ARG... 0x00000000 ..MMC_RSP_NONE CMD_SEND:1 ..ARG... 0x00000000 ..MMC_RSP_R3,4.. 0x00000000 CMD_SEND:1 ..ARG... 0x00000000 ..MMC_RSP_R3,4.. 0x00000000 CMD_SEND:0 ..ARG... 0x00000000 ..MMC_RSP_NONE CMD_SEND:1 ..ARG... 0x00000000 ..MMC_RSP_R3,4.. 0x00000000 CMD_SEND:1 ..ARG... 0x00000000 ..MMC_RSP_R3,4.. 0x00000000 CMD_SEND:2 ..ARG... 0x00000000 ..MMC_RSP_R2.. 0x00000000 .. .. 0x00000000 .. .. 0x00000000 .. .. 0x00000000 .....DUMPING DATA .....000 - 00 00 00 00 .....004 - 00 00 00 00 .....008 - 00 00 00 00 .....012 - 00 00 00 00 CMD_SEND:3 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:9 ..ARG... 0x00000000 ..MMC_RSP_R2.. 0x00000000 .. .. 0x00000000 .. .. 0x00000000 .. .. 0x00000000 .....DUMPING DATA .....000 - 00 00 00 00 .....004 - 00 00 00 00 .....008 - 00 00 00 00 .....012 - 00 00 00 00 CMD_SEND:13 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CURR STATE:3 CMD_SEND:7 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:8 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:8 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:6 ..ARG... 0x00000000 ..MMC_RSP_R1b.. 0x00000000 CMD_SEND:13 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CURR STATE:4 CMD_SEND:8 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:6 ..ARG... 0x00000000 ..RET... -110 CMD_SEND:16 ..ARG... 0x00000000 ..MMC_RSP_R1,5,6,7 . 0x00000000 CMD_SEND:17 ..ARG... 0x00000000 ..RET... -110 test 1 cmdidx: 17 mmc_bread: Failed to read blocks mmc_load_image_raw_sector: mmc block read error SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### > 12 окт. 2016 г., в 18:42, Alexandr Bochkarev <aneox.in...@gmail.com> > написал(а): > > >> I understood more clearly...Your target for using is sdc0(eMMC), right? > Yes > > Now i have checked det pin on my board. I use standart > A20-OLinuXino-Lime_defconfig with my board. > So PH1 is pull-fown. No changes if just remove det pin > > U-Boot SPL 2016.11-rc1-g4dc34be-dirty (Oct 12 2016 - 18:12:37) > DRAM: 512 MiB > Failed to set core voltage! Can't set CPU frequency > Trying to boot from MMC1 > mmc_bread: Failed to read blocks > mmc_load_image_raw_sector: mmc block read error > SPL: failed to boot from all boot devices > ### ERROR ### Please RESET the board ### > > > > Then , i removed det pin from config and build again. Burn it to emmc(sdc2) > on marsboard and tried to boot this board with mainline u-boot, not 2014 as > before and get this. > > U-Boot SPL 2016.11-rc1-g4dc34be-dirty (Oct 12 2016 - 18:24:58) > DRAM: 1024 MiB > CPU: 912000000Hz, AXI/AHB/APB: 3/2/2 > Trying to boot from MMC2 > MMC Device 1 not found > spl: could not find mmc device. error: -19 > SPL: failed to boot from all boot devices > ### ERROR ### Please RESET the board ### > > Something new, error code is 19 ) Looks like it see that no card on sdc0 and > found emmc on sdc2, but fails. > Same code on my board never tries mmc2, so it part works > >> I will try to check codes relevant to sunxi.. > > I hope on your help, thank you very much > > _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot