On 10/19/2016 12:18 PM, Stephen Warren wrote: > On 10/19/2016 09:25 AM, Stephen Warren wrote: >> On 10/14/2016 02:17 PM, York Sun wrote: >>> Current code turns off d-cache first, then flush all levels of cache. >>> This results data loss. As soon as d-cache is off, the dirty cache >>> is discarded according to the test on LS2080A. This issue was not >>> seen as long as external L3 cache was flushed to push the data to >>> main memory. However, external L3 cache is not guaranteed to have >>> the data. To fix this, flush the d-cache by way/set first to make >>> sure cache is clean before turning it off. >> >>> diff --git a/arch/arm/cpu/armv8/cache_v8.c >>> b/arch/arm/cpu/armv8/cache_v8.c >> >>> @@ -478,9 +478,9 @@ void dcache_disable(void) >> >>> + flush_dcache_all(); >>> set_sctlr(sctlr & ~(CR_C|CR_M)); >>> >>> - flush_dcache_all(); >>> __asm_invalidate_tlb_all(); >> >> I talked to Mark Rutland at ARM, and I believe the current code is >> correct. Here's my interpretation of what he said: >> >> The dcache must be disabled first. This prevents allocation of new >> entries in the cache during the flush operation, which prevents the race >> conditions that were mentioned in the other thread. >> >> Then, the flush operation must be invoked. Since the cache is now >> disabled, this can fully flush the cache without worrying about racing >> with things being added to the cache. >> >> This all implies that the implementation of dcache_disable(), >> set_sctlr(), flush_dcache_all(), and any code they call must not access >> data in DRAM at all; since because the dcache is off, any DRAM access >> will[1] read potentially stale data from DRAM, rather than any dirty >> data that might be in the cache. >> >> [1] I'm not sure if that's "will" or "may", i.e. whether this is >> architecturally guaranteed in ARMv8 or is implementation defined. At >> least the Cortex A72 TRM says "will" for that CPU; not sure about others. >> >> Perhaps the most obvious upshot of this is that the stack can't be used. >> This implies to me that we need to recode all those functions purely in >> assembly, or just possibly play some tricks to 100% force gcc not to >> touch memory anywhere inside dcache_disable() or the functions it calls. >> We're just getting lucky here right now since everything happens to be >> inlined, but I don't think we're doing anything to 100% guarantee this. >> >> What worries me here is that at least on Tegra, a "flush the entire >> dcache" operation requires an SMC call to the secure monitor. That will >> certainly access DRAM when the secure monitor runs, but perhaps this >> doesn't matter since that's at a different exception level, and we know >> the secure monitor accesses DRAM regions that are separate from U-Boot's >> DRAM? I suspect life isn't that convenient. I'm wondering if this all >> implies that, like patch 2 in this series, we need to get 100% away from >> flush-by-set/way, even with SoC-specific hooks to make that work >> reliably, and just flush everything by VA, which IIRC is architecturally >> guaranteed to work without SoC-specific logic. That way, we can >> encapsulate everything into an assembly function without worrying about >> calling SMCs or SoC-specific hook functions without using DRAM. Of >> course, how that assembly function knows which VAs to flush without >> decoding the page tables or other data structure is another matter:-( > > Re: the last paragraph there: > > After reading the ARMv8 ARM, I see that EL1, EL2, and EL3 all have > separate cache enable bits in SCTLR_ELx. I believe U-Boot only needs to > flush/... its own RAM out of the dcache, since that's all that's > relevant at the EL U-Boot is running at, and doesn't care about anything > EL3 might have mapped cached. So, it's safe to invoke SMCs from the > cache flush code in U-Boot even if the EL3 code touches its own DRAM. > There might be a corner case where this isn't true if EL3 has some > EL1/EL2-owned RAM mapped, but I don't expect that to be the case here. > > Re: my other series to add more cache hooks: I'll re-implement the Tegra > hook in assembly so it's guaranteed not to touch RAM, retest, and resumbit. > > If it turns out that dcache_disable() ever starts touching DRAM at the > wrong time, we can deal with that then; it doesn't now at least. >
Stephen, I think one of our difference is whether the data is returned correctly with dirty dcache being disabled. With current code flow, the dcache is disabled, followed by flushing/invalidating by way/set, then L3 cache is flushed. I see correct stack after these steps. During my recent attempt to remove flushing L3, I added code to flush the stack by VA (which I already confirmed the data will end up in main memory) to replace flushing L3. I found as soon as the dcache is disabled, the dirty cache data is lost when trying to access from the core (debugged by JTAG tool). This makes me to think the order may be wrong. By reverting the order, i.e. flushing dcache first then disable it, I can see correct data in main memory. I understand the proposed new code requires not touching stack or any data after the first flush. I prefer to not to make this change if we have an explanation of what I saw. York _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot