Hi Stefano, On Mon, Oct 17, 2016 at 11:26 AM, Stefano Babic <sba...@denx.de> wrote: > Hi Jagan, > > On 17/10/2016 05:40, Jagan Teki wrote: >> Hi Stefano, >> >> On Tue, Oct 11, 2016 at 9:00 AM, Jagan Teki <jt...@openedev.com> wrote: >>> Hi Stefano, >>> >>> On Sun, Oct 9, 2016 at 8:15 PM, Jagan Teki <jagannadh.t...@gmail.com> wrote: >>>> Hi Stefano, >>>> >>>> On Sat, Oct 8, 2016 at 6:00 PM, Jagan Teki <jt...@openedev.com> wrote: >>>>> From: Jagan Teki <ja...@amarulasolutions.com> >>>>> >>>>> This series supports Engicam i.CoreM6 QDL modules on top of >>>>> u-boot-imx/master >>>>> and test on the respective starter kits as well. >>>>> >>>>> Tested both MMC and NAND boot. >>>>> >>>>> Changes for v7: >>>>> - Add patch to CONFIG_DEFAULT_FDT_FILE to defconfigs >>>>> - Rebase on u-boot-imx/master >>>>> >>>>> Changes for v6: >>>>> - Rebase to u-boot-imx/master >>>>> - Move few SPL configs to defconfigs >>>>> >>>>> Changes for v5: >>>>> - Add NAND support >>>>> >>>>> Changes for v4: >>>>> - Add 'net: Kconfig: Add FEC_MXC entry' patch >>>>> - Updated ENV configs along with comments >>>>> - Restructured configs for more readability >>>>> - Add CONFIG_ENV_OVERWRITE >>>>> - Rename icorem6qdl_defconfig with icorem6qdl_mmc_defconfig >>>>> >>>>> Changes for v3: >>>>> - Remove "v2 01/17 imx: iomux-v3: Fix build error with snvs base" >>>>> patch >>>>> - Remove 'default n' on Kconfig DEFAULT_FDT_FILE patch >>>>> - Add minimal devicetree support for Engicam i.CoreM6 QDL >>>>> - Add is_mx6dl() >>>>> - Add is_mx6solo() >>>>> - Use is_mx6dq() >>>>> - Add last commit sha1 and header in pull devicetree files from >>>>> Linux >>>>> >>>>> Changes for v2: >>>>> - Make static to local iomux structure in board file >>>>> - Corrected rowaddr in mx6_ddr3_cfg >>>>> - Used imx_ddr_size >>>>> - Add FEC support and tested the same >>>>> - Add DM_GPIO, DM_MMC support >>>>> - Add pinctrl support >>>>> - Add devicetree support >>>>> >>>>> Jagan Teki (21): >>>>> serial: Kconfig: Add MXC_UART entry >>>>> thermal: Kconfig: Add IMX_THERMAL entry >>>>> config: Move CONFIG_DEFAULT_FDT_FILE to defconfigs >>>>> arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support >>>>> net: Kconfig: Add FEC_MXC entry >>>>> imx6: icorem6: Add ENET support >>>>> imx: s/docs\/README.imximage/doc\/README.imximage/g >>>>> arm: dts: Add devicetree for i.MX6DL >>>>> arm: dts: Add devicetree for i.MX6DQL >>>>> arm: dts: imx6dl: Add pinctrl defines >>>>> dt-bindings: clock: imx6qdl: Add clock defines >>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo >>>>> imx6q: icorem6: Enable pinctrl driver >>>>> engicam: icorem6: Add DM_GPIO, DM_MMC support >>>>> arm: dts: Add devicetree for i.MX6Q >>>>> arm: dts: imx6q: Add pinctrl defines >>>>> arm: imx6q: Add devicetree support for Engicam i.CoreM6 Quad/Dual >>>>> mtd: nand: Kconfig: Add NAND_MXS entry >>>>> imx6: icorem6: Add NAND support >>>>> imx6: icorem6: Enable MTD device support >>>>> imx6: icorem6: Add default mtd nand partition table >>>> >>>> All set now, please do apply. >>> >>> Let me know if you still find any issues, otherwise apply this. >>> >> >> Any help? > > Sorry, I was last week at ELCE - I will go on with your patches (and the > other ones left pending) this week.
Please apply this, I need to rebase on top of tom/master and send few more series. thanks! -- Jagan Teki Free Software Engineer | www.openedev.com U-Boot, Linux | Upstream Maintainer Hyderabad, India. _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot