Since the introduction of the pinctrl and clk drivers and the
device tree files, remove unneeded hard coded related code from
the board file.
Signed-off-by: Wenyou Yang <wenyou.y...@atmel.com>
---
board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c | 59 -------------------------
1 file changed, 59 deletions(-)
diff --git a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
index 6871916865..dbc25e96ca 100644
--- a/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
+++ b/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
@@ -17,11 +17,6 @@
#include <lcd.h>
#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
-#include <atmel_mci.h>
-#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-#include <net.h>
-#endif
-#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -149,39 +144,6 @@ static void at91sam9m10g45ek_usb_hw_init(void)
}
#endif
-#ifdef CONFIG_MACB
-static void at91sam9m10g45ek_macb_hw_init(void)
-{
- struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC);
-
- /*
- * Disable pull-up on:
- * RXDV (PA15) => PHY normal mode (not Test mode)
- * ERX0 (PA12) => PHY ADDR0
- * ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
- *
- * PHY has internal pull-down
- */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->pudr);
-
- at91_phy_reset();
-
- /* Re-enable pull-up */
- writel(pin_to_mask(AT91_PIN_PA15) |
- pin_to_mask(AT91_PIN_PA12) |
- pin_to_mask(AT91_PIN_PA13),
- &pioa->puer);
-
- /* And the pins. */
- at91_macb_hw_init();
-}
-#endif
-
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
@@ -280,15 +242,6 @@ void lcd_show_board_info(void)
#endif /* CONFIG_LCD_INFO */
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bis)
-{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI0);
-}
-#endif
-
int board_early_init_f(void)
{
at91_seriald_hw_init();
@@ -319,9 +272,6 @@ int board_init(void)
#ifdef CONFIG_ATMEL_SPI
at91_spi0_hw_init(1 << 4);
#endif
-#ifdef CONFIG_MACB
- at91sam9m10g45ek_macb_hw_init();
-#endif
#ifdef CONFIG_LCD
at91sam9m10g45ek_lcd_hw_init();
#endif
@@ -341,15 +291,6 @@ void reset_phy(void)
}
#endif
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
-#endif
- return rc;
-}
-
/* SPI chip select control */
#ifdef CONFIG_ATMEL_SPI
#include <spi.h>
--
2.11.0
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
