On 05/05/2017 12:26 PM, tien.fong.c...@intel.com wrote: > From: Tien Fong Chee <tien.fong.c...@intel.com> > > Move FPGA driver which is Gen5 specific code into Gen5 files. > No functional change.
It's a driver, so it should stay in drivers/ . If you need to split it, split it in drivers/fpga/ and add Kconfig option(s) > Signed-off-by: Tien Fong Chee <tien.fong.c...@intel.com> > --- > arch/arm/mach-socfpga/Makefile | 2 +- > arch/arm/mach-socfpga/include/mach/fpga_manager.h | 65 +---- > .../mach/{fpga_manager.h => fpga_manager_gen5.h} | 69 +++--- > drivers/Makefile | 1 + > drivers/fpga/Makefile | 1 + > drivers/fpga/socfpga.c | 267 > +------------------- > drivers/fpga/{socfpga.c => socfpga_gen5.c} | 29 +-- > 7 files changed, 48 insertions(+), 386 deletions(-) > copy arch/arm/mach-socfpga/include/mach/{fpga_manager.h => > fpga_manager_gen5.h} (57%) > copy drivers/fpga/{socfpga.c => socfpga_gen5.c} (92%) > > diff --git a/arch/arm/mach-socfpga/Makefile b/arch/arm/mach-socfpga/Makefile > index 41b779c..286bfef 100644 > --- a/arch/arm/mach-socfpga/Makefile > +++ b/arch/arm/mach-socfpga/Makefile > @@ -9,7 +9,6 @@ > > obj-y += board.o > obj-y += clock_manager.o > -obj-y += fpga_manager.o > obj-y += misc.o > obj-y += reset_manager.o > obj-y += timer.o > @@ -21,6 +20,7 @@ obj-y += reset_manager_gen5.o > obj-y += scan_manager.o > obj-y += system_manager_gen5.o > obj-y += wrap_pll_config.o > +obj-y += fpga_manager.o > endif > > ifdef CONFIG_TARGET_SOCFPGA_ARRIA10 > diff --git a/arch/arm/mach-socfpga/include/mach/fpga_manager.h > b/arch/arm/mach-socfpga/include/mach/fpga_manager.h > index a077e22..69d8613 100644 > --- a/arch/arm/mach-socfpga/include/mach/fpga_manager.h > +++ b/arch/arm/mach-socfpga/include/mach/fpga_manager.h > @@ -1,5 +1,5 @@ > /* > - * Copyright (C) 2012 Altera Corporation <www.altera.com> > + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com> > * All rights reserved. > * > * SPDX-License-Identifier: BSD-3-Clause > @@ -10,58 +10,9 @@ > > #include <altera.h> > > -struct socfpga_fpga_manager { > - /* FPGA Manager Module */ > - u32 stat; /* 0x00 */ > - u32 ctrl; > - u32 dclkcnt; > - u32 dclkstat; > - u32 gpo; /* 0x10 */ > - u32 gpi; > - u32 misci; /* 0x18 */ > - u32 _pad_0x1c_0x82c[517]; > - > - /* Configuration Monitor (MON) Registers */ > - u32 gpio_inten; /* 0x830 */ > - u32 gpio_intmask; > - u32 gpio_inttype_level; > - u32 gpio_int_polarity; > - u32 gpio_intstatus; /* 0x840 */ > - u32 gpio_raw_intstatus; > - u32 _pad_0x848; > - u32 gpio_porta_eoi; > - u32 gpio_ext_porta; /* 0x850 */ > - u32 _pad_0x854_0x85c[3]; > - u32 gpio_1s_sync; /* 0x860 */ > - u32 _pad_0x864_0x868[2]; > - u32 gpio_ver_id_code; > - u32 gpio_config_reg2; /* 0x870 */ > - u32 gpio_config_reg1; > -}; > - > -#define FPGAMGRREGS_STAT_MODE_MASK 0x7 > -#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8 > -#define FPGAMGRREGS_STAT_MSEL_LSB 3 > - > -#define FPGAMGRREGS_CTRL_CFGWDTH_MASK 0x200 > -#define FPGAMGRREGS_CTRL_AXICFGEN_MASK 0x100 > -#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK 0x4 > -#define FPGAMGRREGS_CTRL_NCE_MASK 0x2 > -#define FPGAMGRREGS_CTRL_EN_MASK 0x1 > -#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6 > - > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK 0x8 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK 0x4 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK 0x2 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK 0x1 > - > -/* FPGA Mode */ > -#define FPGAMGRREGS_MODE_FPGAOFF 0x0 > -#define FPGAMGRREGS_MODE_RESETPHASE 0x1 > -#define FPGAMGRREGS_MODE_CFGPHASE 0x2 > -#define FPGAMGRREGS_MODE_INITPHASE 0x3 > -#define FPGAMGRREGS_MODE_USERMODE 0x4 > -#define FPGAMGRREGS_MODE_UNKNOWN 0x5 > +#if defined(CONFIG_TARGET_SOCFPGA_GEN5) > +#include <asm/arch/fpga_manager_gen5.h> > +#endif > > /* FPGA CD Ratio Value */ > #define CDRATIO_x1 0x0 > @@ -74,4 +25,12 @@ int fpgamgr_test_fpga_ready(void); > int fpgamgr_poll_fpga_ready(void); > int fpgamgr_get_mode(void); > > +#define FPGA_TIMEOUT_CNT 0x1000000 > + > +#ifndef __ASSEMBLY__ > + > +/* Common prototypes */ > +int fpgamgr_dclkcnt_set(unsigned long cnt); > + > +#endif /* __ASSEMBLY__ */ > #endif /* _FPGA_MANAGER_H_ */ > diff --git a/arch/arm/mach-socfpga/include/mach/fpga_manager.h > b/arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h > similarity index 57% > copy from arch/arm/mach-socfpga/include/mach/fpga_manager.h > copy to arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h > index a077e22..2de7a11 100644 > --- a/arch/arm/mach-socfpga/include/mach/fpga_manager.h > +++ b/arch/arm/mach-socfpga/include/mach/fpga_manager_gen5.h > @@ -1,14 +1,38 @@ > /* > - * Copyright (C) 2012 Altera Corporation <www.altera.com> > + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com> > * All rights reserved. > * > * SPDX-License-Identifier: BSD-3-Clause > */ > > -#ifndef _FPGA_MANAGER_H_ > -#define _FPGA_MANAGER_H_ > +#ifndef _FPGA_MANAGER_GEN5_H_ > +#define _FPGA_MANAGER_GEN5_H_ > > -#include <altera.h> > +#define FPGAMGRREGS_STAT_MODE_MASK 0x7 > +#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8 > +#define FPGAMGRREGS_STAT_MSEL_LSB 3 > + > +#define FPGAMGRREGS_CTRL_CFGWDTH_MASK BIT(9) > +#define FPGAMGRREGS_CTRL_AXICFGEN_MASK BIT(8) > +#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK BIT(2) > +#define FPGAMGRREGS_CTRL_NCE_MASK BIT(1) > +#define FPGAMGRREGS_CTRL_EN_MASK BIT(0) > +#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6 > + > +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK BIT(3) > +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK BIT(2) > +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK BIT(1) > +#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK BIT(0) > + > +/* FPGA Mode */ > +#define FPGAMGRREGS_MODE_FPGAOFF 0x0 > +#define FPGAMGRREGS_MODE_RESETPHASE 0x1 > +#define FPGAMGRREGS_MODE_CFGPHASE 0x2 > +#define FPGAMGRREGS_MODE_INITPHASE 0x3 > +#define FPGAMGRREGS_MODE_USERMODE 0x4 > +#define FPGAMGRREGS_MODE_UNKNOWN 0x5 > + > +#ifndef __ASSEMBLY__ > > struct socfpga_fpga_manager { > /* FPGA Manager Module */ > @@ -39,39 +63,6 @@ struct socfpga_fpga_manager { > u32 gpio_config_reg1; > }; > > -#define FPGAMGRREGS_STAT_MODE_MASK 0x7 > -#define FPGAMGRREGS_STAT_MSEL_MASK 0xf8 > -#define FPGAMGRREGS_STAT_MSEL_LSB 3 > - > -#define FPGAMGRREGS_CTRL_CFGWDTH_MASK 0x200 > -#define FPGAMGRREGS_CTRL_AXICFGEN_MASK 0x100 > -#define FPGAMGRREGS_CTRL_NCONFIGPULL_MASK 0x4 > -#define FPGAMGRREGS_CTRL_NCE_MASK 0x2 > -#define FPGAMGRREGS_CTRL_EN_MASK 0x1 > -#define FPGAMGRREGS_CTRL_CDRATIO_LSB 6 > - > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CRC_MASK 0x8 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_ID_MASK 0x4 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK 0x2 > -#define FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK 0x1 > - > -/* FPGA Mode */ > -#define FPGAMGRREGS_MODE_FPGAOFF 0x0 > -#define FPGAMGRREGS_MODE_RESETPHASE 0x1 > -#define FPGAMGRREGS_MODE_CFGPHASE 0x2 > -#define FPGAMGRREGS_MODE_INITPHASE 0x3 > -#define FPGAMGRREGS_MODE_USERMODE 0x4 > -#define FPGAMGRREGS_MODE_UNKNOWN 0x5 > - > -/* FPGA CD Ratio Value */ > -#define CDRATIO_x1 0x0 > -#define CDRATIO_x2 0x1 > -#define CDRATIO_x4 0x2 > -#define CDRATIO_x8 0x3 > - > -/* SoCFPGA support functions */ > -int fpgamgr_test_fpga_ready(void); > -int fpgamgr_poll_fpga_ready(void); > -int fpgamgr_get_mode(void); > +#endif /* __ASSEMBLY__ */ > > -#endif /* _FPGA_MANAGER_H_ */ > +#endif /* _FPGA_MANAGER_GEN5_H_ */ > diff --git a/drivers/Makefile b/drivers/Makefile > index 4a4b237..b4a2230 100644 > --- a/drivers/Makefile > +++ b/drivers/Makefile > @@ -47,6 +47,7 @@ obj-$(CONFIG_OMAP_USB_PHY) += usb/phy/ > obj-$(CONFIG_SPL_SATA_SUPPORT) += block/ > obj-$(CONFIG_SPL_USB_HOST_SUPPORT) += block/ > obj-$(CONFIG_SPL_MMC_SUPPORT) += block/ > +obj-$(CONFIG_FPGA) += fpga/ > endif > > ifdef CONFIG_TPL_BUILD > diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile > index 84e7605..649b6d1 100644 > --- a/drivers/fpga/Makefile > +++ b/drivers/fpga/Makefile > @@ -19,4 +19,5 @@ obj-$(CONFIG_FPGA_ACEX1K) += ACEX1K.o > obj-$(CONFIG_FPGA_CYCLON2) += cyclon2.o > obj-$(CONFIG_FPGA_STRATIX_II) += stratixII.o > obj-$(CONFIG_FPGA_STRATIX_V) += stratixv.o > +obj-$(CONFIG_TARGET_SOCFPGA_GEN5) += socfpga_gen5.o > endif > diff --git a/drivers/fpga/socfpga.c b/drivers/fpga/socfpga.c > index f1b2f2c..30ebee8 100644 > --- a/drivers/fpga/socfpga.c > +++ b/drivers/fpga/socfpga.c > @@ -1,5 +1,5 @@ > /* > - * Copyright (C) 2012 Altera Corporation <www.altera.com> > + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com> > * All rights reserved. > * > * SPDX-License-Identifier: BSD-3-Clause > @@ -14,23 +14,10 @@ > > DECLARE_GLOBAL_DATA_PTR; > > -/* Timeout count */ > -#define FPGA_TIMEOUT_CNT 0x1000000 > - > static struct socfpga_fpga_manager *fpgamgr_regs = > (struct socfpga_fpga_manager *)SOCFPGA_FPGAMGRREGS_ADDRESS; > -static struct socfpga_system_manager *sysmgr_regs = > - (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS; > - > -/* Set CD ratio */ > -static void fpgamgr_set_cd_ratio(unsigned long ratio) > -{ > - clrsetbits_le32(&fpgamgr_regs->ctrl, > - 0x3 << FPGAMGRREGS_CTRL_CDRATIO_LSB, > - (ratio & 0x3) << FPGAMGRREGS_CTRL_CDRATIO_LSB); > -} > > -static int fpgamgr_dclkcnt_set(unsigned long cnt) > +int fpgamgr_dclkcnt_set(unsigned long cnt) > { > unsigned long i; > > @@ -52,253 +39,3 @@ static int fpgamgr_dclkcnt_set(unsigned long cnt) > > return -ETIMEDOUT; > } > - > -/* Start the FPGA programming by initialize the FPGA Manager */ > -static int fpgamgr_program_init(void) > -{ > - unsigned long msel, i; > - > - /* Get the MSEL value */ > - msel = readl(&fpgamgr_regs->stat); > - msel &= FPGAMGRREGS_STAT_MSEL_MASK; > - msel >>= FPGAMGRREGS_STAT_MSEL_LSB; > - > - /* > - * Set the cfg width > - * If MSEL[3] = 1, cfg width = 32 bit > - */ > - if (msel & 0x8) { > - setbits_le32(&fpgamgr_regs->ctrl, > - FPGAMGRREGS_CTRL_CFGWDTH_MASK); > - > - /* To determine the CD ratio */ > - /* MSEL[1:0] = 0, CD Ratio = 1 */ > - if ((msel & 0x3) == 0x0) > - fpgamgr_set_cd_ratio(CDRATIO_x1); > - /* MSEL[1:0] = 1, CD Ratio = 4 */ > - else if ((msel & 0x3) == 0x1) > - fpgamgr_set_cd_ratio(CDRATIO_x4); > - /* MSEL[1:0] = 2, CD Ratio = 8 */ > - else if ((msel & 0x3) == 0x2) > - fpgamgr_set_cd_ratio(CDRATIO_x8); > - > - } else { /* MSEL[3] = 0 */ > - clrbits_le32(&fpgamgr_regs->ctrl, > - FPGAMGRREGS_CTRL_CFGWDTH_MASK); > - > - /* To determine the CD ratio */ > - /* MSEL[1:0] = 0, CD Ratio = 1 */ > - if ((msel & 0x3) == 0x0) > - fpgamgr_set_cd_ratio(CDRATIO_x1); > - /* MSEL[1:0] = 1, CD Ratio = 2 */ > - else if ((msel & 0x3) == 0x1) > - fpgamgr_set_cd_ratio(CDRATIO_x2); > - /* MSEL[1:0] = 2, CD Ratio = 4 */ > - else if ((msel & 0x3) == 0x2) > - fpgamgr_set_cd_ratio(CDRATIO_x4); > - } > - > - /* To enable FPGA Manager configuration */ > - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCE_MASK); > - > - /* To enable FPGA Manager drive over configuration line */ > - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_EN_MASK); > - > - /* Put FPGA into reset phase */ > - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCONFIGPULL_MASK); > - > - /* (1) wait until FPGA enter reset phase */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_RESETPHASE) > - break; > - } > - > - /* If not in reset state, return error */ > - if (fpgamgr_get_mode() != FPGAMGRREGS_MODE_RESETPHASE) { > - puts("FPGA: Could not reset\n"); > - return -1; > - } > - > - /* Release FPGA from reset phase */ > - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_NCONFIGPULL_MASK); > - > - /* (2) wait until FPGA enter configuration phase */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_CFGPHASE) > - break; > - } > - > - /* If not in configuration state, return error */ > - if (fpgamgr_get_mode() != FPGAMGRREGS_MODE_CFGPHASE) { > - puts("FPGA: Could not configure\n"); > - return -2; > - } > - > - /* Clear all interrupts in CB Monitor */ > - writel(0xFFF, &fpgamgr_regs->gpio_porta_eoi); > - > - /* Enable AXI configuration */ > - setbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_AXICFGEN_MASK); > - > - return 0; > -} > - > -/* Write the RBF data to FPGA Manager */ > -static void fpgamgr_program_write(const void *rbf_data, unsigned long > rbf_size) > -{ > - uint32_t src = (uint32_t)rbf_data; > - uint32_t dst = SOCFPGA_FPGAMGRDATA_ADDRESS; > - > - /* Number of loops for 32-byte long copying. */ > - uint32_t loops32 = rbf_size / 32; > - /* Number of loops for 4-byte long copying + trailing bytes */ > - uint32_t loops4 = DIV_ROUND_UP(rbf_size % 32, 4); > - > - asm volatile( > - "1: ldmia %0!, {r0-r7}\n" > - " stmia %1!, {r0-r7}\n" > - " sub %1, #32\n" > - " subs %2, #1\n" > - " bne 1b\n" > - " cmp %3, #0\n" > - " beq 3f\n" > - "2: ldr %2, [%0], #4\n" > - " str %2, [%1]\n" > - " subs %3, #1\n" > - " bne 2b\n" > - "3: nop\n" > - : "+r"(src), "+r"(dst), "+r"(loops32), "+r"(loops4) : > - : "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", "cc"); > -} > - > -/* Ensure the FPGA entering config done */ > -static int fpgamgr_program_poll_cd(void) > -{ > - const uint32_t mask = FPGAMGRREGS_MON_GPIO_EXT_PORTA_NS_MASK | > - FPGAMGRREGS_MON_GPIO_EXT_PORTA_CD_MASK; > - unsigned long reg, i; > - > - /* (3) wait until full config done */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - reg = readl(&fpgamgr_regs->gpio_ext_porta); > - > - /* Config error */ > - if (!(reg & mask)) { > - printf("FPGA: Configuration error.\n"); > - return -3; > - } > - > - /* Config done without error */ > - if (reg & mask) > - break; > - } > - > - /* Timeout happened, return error */ > - if (i == FPGA_TIMEOUT_CNT) { > - printf("FPGA: Timeout waiting for program.\n"); > - return -4; > - } > - > - /* Disable AXI configuration */ > - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_AXICFGEN_MASK); > - > - return 0; > -} > - > -/* Ensure the FPGA entering init phase */ > -static int fpgamgr_program_poll_initphase(void) > -{ > - unsigned long i; > - > - /* Additional clocks for the CB to enter initialization phase */ > - if (fpgamgr_dclkcnt_set(0x4)) > - return -5; > - > - /* (4) wait until FPGA enter init phase or user mode */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_INITPHASE) > - break; > - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_USERMODE) > - break; > - } > - > - /* If not in configuration state, return error */ > - if (i == FPGA_TIMEOUT_CNT) > - return -6; > - > - return 0; > -} > - > -/* Ensure the FPGA entering user mode */ > -static int fpgamgr_program_poll_usermode(void) > -{ > - unsigned long i; > - > - /* Additional clocks for the CB to exit initialization phase */ > - if (fpgamgr_dclkcnt_set(0x5000)) > - return -7; > - > - /* (5) wait until FPGA enter user mode */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - if (fpgamgr_get_mode() == FPGAMGRREGS_MODE_USERMODE) > - break; > - } > - /* If not in configuration state, return error */ > - if (i == FPGA_TIMEOUT_CNT) > - return -8; > - > - /* To release FPGA Manager drive over configuration line */ > - clrbits_le32(&fpgamgr_regs->ctrl, FPGAMGRREGS_CTRL_EN_MASK); > - > - return 0; > -} > - > -/* > - * FPGA Manager to program the FPGA. This is the interface used by FPGA > driver. > - * Return 0 for sucess, non-zero for error. > - */ > -int socfpga_load(Altera_desc *desc, const void *rbf_data, size_t rbf_size) > -{ > - unsigned long status; > - > - if ((uint32_t)rbf_data & 0x3) { > - puts("FPGA: Unaligned data, realign to 32bit boundary.\n"); > - return -EINVAL; > - } > - > - /* Prior programming the FPGA, all bridges need to be shut off */ > - > - /* Disable all signals from hps peripheral controller to fpga */ > - writel(0, &sysmgr_regs->fpgaintfgrp_module); > - > - /* Disable all signals from FPGA to HPS SDRAM */ > -#define SDR_CTRLGRP_FPGAPORTRST_ADDRESS 0x5080 > - writel(0, SOCFPGA_SDR_ADDRESS + SDR_CTRLGRP_FPGAPORTRST_ADDRESS); > - > - /* Disable all axi bridge (hps2fpga, lwhps2fpga & fpga2hps) */ > - socfpga_bridges_reset(1); > - > - /* Unmap the bridges from NIC-301 */ > - writel(0x1, SOCFPGA_L3REGS_ADDRESS); > - > - /* Initialize the FPGA Manager */ > - status = fpgamgr_program_init(); > - if (status) > - return status; > - > - /* Write the RBF data to FPGA Manager */ > - fpgamgr_program_write(rbf_data, rbf_size); > - > - /* Ensure the FPGA entering config done */ > - status = fpgamgr_program_poll_cd(); > - if (status) > - return status; > - > - /* Ensure the FPGA entering init phase */ > - status = fpgamgr_program_poll_initphase(); > - if (status) > - return status; > - > - /* Ensure the FPGA entering user mode */ > - return fpgamgr_program_poll_usermode(); > -} > diff --git a/drivers/fpga/socfpga.c b/drivers/fpga/socfpga_gen5.c > similarity index 92% > copy from drivers/fpga/socfpga.c > copy to drivers/fpga/socfpga_gen5.c > index f1b2f2c..6992d83 100644 > --- a/drivers/fpga/socfpga.c > +++ b/drivers/fpga/socfpga_gen5.c > @@ -1,5 +1,5 @@ > /* > - * Copyright (C) 2012 Altera Corporation <www.altera.com> > + * Copyright (C) 2012-2017 Altera Corporation <www.altera.com> > * All rights reserved. > * > * SPDX-License-Identifier: BSD-3-Clause > @@ -14,9 +14,6 @@ > > DECLARE_GLOBAL_DATA_PTR; > > -/* Timeout count */ > -#define FPGA_TIMEOUT_CNT 0x1000000 > - > static struct socfpga_fpga_manager *fpgamgr_regs = > (struct socfpga_fpga_manager *)SOCFPGA_FPGAMGRREGS_ADDRESS; > static struct socfpga_system_manager *sysmgr_regs = > @@ -30,29 +27,6 @@ static void fpgamgr_set_cd_ratio(unsigned long ratio) > (ratio & 0x3) << FPGAMGRREGS_CTRL_CDRATIO_LSB); > } > > -static int fpgamgr_dclkcnt_set(unsigned long cnt) > -{ > - unsigned long i; > - > - /* Clear any existing done status */ > - if (readl(&fpgamgr_regs->dclkstat)) > - writel(0x1, &fpgamgr_regs->dclkstat); > - > - /* Write the dclkcnt */ > - writel(cnt, &fpgamgr_regs->dclkcnt); > - > - /* Wait till the dclkcnt done */ > - for (i = 0; i < FPGA_TIMEOUT_CNT; i++) { > - if (!readl(&fpgamgr_regs->dclkstat)) > - continue; > - > - writel(0x1, &fpgamgr_regs->dclkstat); > - return 0; > - } > - > - return -ETIMEDOUT; > -} > - > /* Start the FPGA programming by initialize the FPGA Manager */ > static int fpgamgr_program_init(void) > { > @@ -267,7 +241,6 @@ int socfpga_load(Altera_desc *desc, const void *rbf_data, > size_t rbf_size) > } > > /* Prior programming the FPGA, all bridges need to be shut off */ > - > /* Disable all signals from hps peripheral controller to fpga */ > writel(0, &sysmgr_regs->fpgaintfgrp_module); > > -- Best regards, Marek Vasut _______________________________________________ U-Boot mailing list U-Boot@lists.denx.de https://lists.denx.de/listinfo/u-boot