This converts the following to Kconfig:
CONFIG_ENV_IS_IN_EEPROM
Signed-off-by: Simon Glass <s...@chromium.org>
---
README | 60 ------------------------------------
configs/imx31_phycore_defconfig | 1 +
configs/imx31_phycore_eet_defconfig | 1 +
configs/km_kirkwood_128m16_defconfig | 1 +
configs/km_kirkwood_defconfig | 1 +
configs/km_kirkwood_pci_defconfig | 1 +
configs/mgcoge3un_defconfig | 1 +
configs/portl2_defconfig | 1 +
env/Kconfig | 60 ++++++++++++++++++++++++++++++++++++
include/config_fsl_chain_trust.h | 1 -
include/configs/imx31_phycore.h | 1 -
include/configs/km/km_arm.h | 1 -
scripts/config_whitelist.txt | 1 -
13 files changed, 67 insertions(+), 64 deletions(-)
diff --git a/README b/README
index cf692e5da3..a2ff039d17 100644
--- a/README
+++ b/README
@@ -3444,66 +3444,6 @@ environment in RAM: we could work on NVRAM directly, but
we want to
keep settings there always unmodified except somebody uses "saveenv"
to save the current settings.
-
-- CONFIG_ENV_IS_IN_EEPROM:
-
- Use this if you have an EEPROM or similar serial access
- device and a driver for it.
-
- - CONFIG_ENV_OFFSET:
- - CONFIG_ENV_SIZE:
-
- These two #defines specify the offset and size of the
- environment area within the total memory of your EEPROM.
-
- - CONFIG_SYS_I2C_EEPROM_ADDR:
- If defined, specified the chip address of the EEPROM device.
- The default address is zero.
-
- - CONFIG_SYS_I2C_EEPROM_BUS:
- If defined, specified the i2c bus of the EEPROM device.
-
- - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
- If defined, the number of bits used to address bytes in a
- single page in the EEPROM device. A 64 byte page, for example
- would require six bits.
-
- - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
- If defined, the number of milliseconds to delay between
- page writes. The default is zero milliseconds.
-
- - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
- The length in bytes of the EEPROM memory array address. Note
- that this is NOT the chip address length!
-
- - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
- EEPROM chips that implement "address overflow" are ones
- like Catalyst 24WC04/08/16 which has 9/10/11 bits of
- address and the extra bits end up in the "chip address" bit
- slots. This makes a 24WC08 (1Kbyte) chip look like four 256
- byte chips.
-
- Note that we consider the length of the address field to
- still be one byte because the extra address bits are hidden
- in the chip address.
-
- - CONFIG_SYS_EEPROM_SIZE:
- The size in bytes of the EEPROM device.
-
- - CONFIG_ENV_EEPROM_IS_ON_I2C
- define this, if you have I2C and SPI activated, and your
- EEPROM, which holds the environment, is on the I2C bus.
-
- - CONFIG_I2C_ENV_EEPROM_BUS
- if you have an Environment on an EEPROM reached over
- I2C muxes, you can define here, how to reach this
- EEPROM. For example:
-
- #define CONFIG_I2C_ENV_EEPROM_BUS 1
-
- EEPROM which holds the environment, is reached over
- a pca9547 i2c mux with address 0x70, channel 3.
-
- CONFIG_ENV_IS_IN_DATAFLASH:
Define this if you have a DataFlash memory device which you
diff --git a/configs/imx31_phycore_defconfig b/configs/imx31_phycore_defconfig
index 224bedb1d6..652fe8662c 100644
--- a/configs/imx31_phycore_defconfig
+++ b/configs/imx31_phycore_defconfig
@@ -6,5 +6,6 @@ CONFIG_CMD_EEPROM=y
CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_PING=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/imx31_phycore_eet_defconfig
b/configs/imx31_phycore_eet_defconfig
index c881b8fdcc..2a0033d615 100644
--- a/configs/imx31_phycore_eet_defconfig
+++ b/configs/imx31_phycore_eet_defconfig
@@ -10,5 +10,6 @@ CONFIG_CMD_I2C=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_PING=y
CONFIG_CMD_BMP=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_MTD_NOR_FLASH=y
diff --git a/configs/km_kirkwood_128m16_defconfig
b/configs/km_kirkwood_128m16_defconfig
index df7dac8c37..eed0ebe341 100644
--- a/configs/km_kirkwood_128m16_defconfig
+++ b/configs/km_kirkwood_128m16_defconfig
@@ -21,6 +21,7 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/km_kirkwood_defconfig b/configs/km_kirkwood_defconfig
index 4b9cdb7f47..766753165c 100644
--- a/configs/km_kirkwood_defconfig
+++ b/configs/km_kirkwood_defconfig
@@ -21,6 +21,7 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/km_kirkwood_pci_defconfig
b/configs/km_kirkwood_pci_defconfig
index 79952774ae..6a74864dc6 100644
--- a/configs/km_kirkwood_pci_defconfig
+++ b/configs/km_kirkwood_pci_defconfig
@@ -21,6 +21,7 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/mgcoge3un_defconfig b/configs/mgcoge3un_defconfig
index 2add8828b8..00a85e3c44 100644
--- a/configs/mgcoge3un_defconfig
+++ b/configs/mgcoge3un_defconfig
@@ -21,6 +21,7 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/configs/portl2_defconfig b/configs/portl2_defconfig
index a0faba50ff..eb741804aa 100644
--- a/configs/portl2_defconfig
+++ b/configs/portl2_defconfig
@@ -21,6 +21,7 @@ CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_JFFS2=y
CONFIG_CMD_UBI=y
+CONFIG_ENV_IS_IN_EEPROM=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_STMICRO=y
diff --git a/env/Kconfig b/env/Kconfig
index 75dd57843f..30a493fcdd 100644
--- a/env/Kconfig
+++ b/env/Kconfig
@@ -1,5 +1,65 @@
menu "Environment"
+config ENV_IS_IN_EEPROM
+ bool "Environment in EEPROM"
+ help
+ Use this if you have an EEPROM or similar serial access
+ device and a driver for it.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the total memory of your EEPROM.
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR:
+ If defined, specified the chip address of the EEPROM device.
+ The default address is zero.
+
+ - CONFIG_SYS_I2C_EEPROM_BUS:
+ If defined, specified the i2c bus of the EEPROM device.
+
+ - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
+ If defined, the number of bits used to address bytes in a
+ single page in the EEPROM device. A 64 byte page, for example
+ would require six bits.
+
+ - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
+ If defined, the number of milliseconds to delay between
+ page writes. The default is zero milliseconds.
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
+ The length in bytes of the EEPROM memory array address. Note
+ that this is NOT the chip address length!
+
+ - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
+ EEPROM chips that implement "address overflow" are ones
+ like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+ address and the extra bits end up in the "chip address" bit
+ slots. This makes a 24WC08 (1Kbyte) chip look like four 256
+ byte chips.
+
+ Note that we consider the length of the address field to
+ still be one byte because the extra address bits are hidden
+ in the chip address.
+
+ - CONFIG_SYS_EEPROM_SIZE:
+ The size in bytes of the EEPROM device.
+
+ - CONFIG_ENV_EEPROM_IS_ON_I2C
+ define this, if you have I2C and SPI activated, and your
+ EEPROM, which holds the environment, is on the I2C bus.
+
+ - CONFIG_I2C_ENV_EEPROM_BUS
+ if you have an Environment on an EEPROM reached over
+ I2C muxes, you can define here, how to reach this
+ EEPROM. For example:
+
+ #define CONFIG_I2C_ENV_EEPROM_BUS 1
+
+ EEPROM which holds the environment, is reached over
+ a pca9547 i2c mux with address 0x70, channel 3.
+
config ENV_IS_IN_FLASH
bool "Environment in flash memory"
help
diff --git a/include/config_fsl_chain_trust.h b/include/config_fsl_chain_trust.h
index 6b6ae7cc78..195419b888 100644
--- a/include/config_fsl_chain_trust.h
+++ b/include/config_fsl_chain_trust.h
@@ -13,7 +13,6 @@
*/
#ifdef CONFIG_SECURE_BOOT
-#undef CONFIG_ENV_IS_IN_EEPROM
#undef CONFIG_ENV_IS_IN_SPI_FLASH
#endif
diff --git a/include/configs/imx31_phycore.h b/include/configs/imx31_phycore.h
index 739af03e88..ba7c3e186d 100644
--- a/include/configs/imx31_phycore.h
+++ b/include/configs/imx31_phycore.h
@@ -135,7 +135,6 @@
/* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_OFFSET 0x00 /* env. starts here */
#define CONFIG_ENV_SIZE 4096
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x52
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 0c5f6e7515..9a90e08d65 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -222,7 +222,6 @@ int get_scl(void);
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_TOTAL_SIZE 0x20000 /* no bracets! */
#else
-#define CONFIG_ENV_IS_IN_EEPROM /* use EEPROM for environment
vars */
#define CONFIG_SYS_DEF_EEPROM_ADDR 0x50
#define CONFIG_ENV_EEPROM_IS_ON_I2C
#define CONFIG_SYS_EEPROM_WREN
diff --git a/scripts/config_whitelist.txt b/scripts/config_whitelist.txt
index 4d8f849757..b7694cd5ec 100644
--- a/scripts/config_whitelist.txt
+++ b/scripts/config_whitelist.txt
@@ -642,7 +642,6 @@ CONFIG_ENV_FLASHBOOT
CONFIG_ENV_IS_EMBEDDED
CONFIG_ENV_IS_IN_
CONFIG_ENV_IS_IN_DATAFLASH
-CONFIG_ENV_IS_IN_EEPROM
CONFIG_ENV_IS_IN_FAT
CONFIG_ENV_IS_IN_MRAM
CONFIG_ENV_IS_IN_ONENAND
--
2.13.2.725.g09c95d1e9-goog
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot
