[U-Boot] [PATCH 1/2] spi: fsl_qspi: support i.MX6UL/7D

[Peng Fan]

The QSPI module on i.MX7D is modified from i.MX6SX. The module used on
i.MX6UL is reused from i.MX7D. They share same tx buffer size.

The endianness is not set at qspi driver initialization. So if we don't
boot from QSPI, we will get wrong endianness when accessing from AHB
address directly.

Add the compatible entry for 6ul/7d.

Signed-off-by: Peng Fan <peng....@nxp.com>
---
 drivers/spi/fsl_qspi.c | 16 ++++++++++++++--
 1 file changed, 14 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/fsl_qspi.c b/drivers/spi/fsl_qspi.c
index 0f3f7d97f0..e37f4538e2 100644
--- a/drivers/spi/fsl_qspi.c
+++ b/drivers/spi/fsl_qspi.c
@@ -20,7 +20,7 @@
 DECLARE_GLOBAL_DATA_PTR;
 
 #define RX_BUFFER_SIZE         0x80
-#ifdef CONFIG_MX6SX
+#if defined(CONFIG_MX6SX) || defined(CONFIG_MX6UL) || defined(CONFIG_MX7D)
 #define TX_BUFFER_SIZE         0x200
 #else
 #define TX_BUFFER_SIZE         0x40
@@ -268,7 +268,7 @@ static void qspi_set_lut(struct fsl_qspi_priv *priv)
                             INSTR0(LUT_CMD) | OPRND1(ADDR32BIT) |
                             PAD1(LUT_PAD1) | INSTR1(LUT_ADDR));
 #endif
-#ifdef CONFIG_MX6SX
+#if defined(CONFIG_MX6SX) || defined(CONFIG_MX6UL) || defined(CONFIG_MX7D)
        /*
         * To MX6SX, OPRND0(TX_BUFFER_SIZE) can not work correctly.
         * So, Use IDATSZ in IPCR to determine the size and here set 0.
@@ -905,6 +905,11 @@ struct spi_slave *spi_setup_slave(unsigned int bus, 
unsigned int cs,
        qspi->slave.max_write_size = TX_BUFFER_SIZE;
 
        mcr_val = qspi_read32(qspi->priv.flags, &regs->mcr);
+
+       /* Set endianness to LE for i.mx */
+       if (IS_ENABLED(CONFIG_MX6) || IS_ENABLED(CONFIG_MX7))
+               mcr_val = QSPI_MCR_END_CFD_LE;
+
        qspi_write32(qspi->priv.flags, &regs->mcr,
                     QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK |
                     (mcr_val & QSPI_MCR_END_CFD_MASK));
@@ -1023,6 +1028,11 @@ static int fsl_qspi_probe(struct udevice *bus)
        }
 
        mcr_val = qspi_read32(priv->flags, &priv->regs->mcr);
+
+       /* Set endianness to LE for i.mx */
+       if (IS_ENABLED(CONFIG_MX6) || IS_ENABLED(CONFIG_MX7))
+               mcr_val = QSPI_MCR_END_CFD_LE;
+
        qspi_write32(priv->flags, &priv->regs->mcr,
                     QSPI_MCR_RESERVED_MASK | QSPI_MCR_MDIS_MASK |
                     (mcr_val & QSPI_MCR_END_CFD_MASK));
@@ -1227,6 +1237,8 @@ static const struct dm_spi_ops fsl_qspi_ops = {
 static const struct udevice_id fsl_qspi_ids[] = {
        { .compatible = "fsl,vf610-qspi" },
        { .compatible = "fsl,imx6sx-qspi" },
+       { .compatible = "fsl,imx6ul-qspi" },
+       { .compatible = "fsl,imx7d-qspi" },
        { }
 };
 
-- 
2.14.1

_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
https://lists.denx.de/listinfo/u-boot